Thanks for the video. This helped me finally getting the fuel rails out. What also helped me was reading the instructions again and following them by taking the fuel pressure sensor off the passenger side rail. This gave just enough room to finagle the driver's side rail out.
Thanks for the Video I got the rail out but started to second guess how the injectors were in there because they are tight. This is super helpful you rock!
Thanks man, it was tight and this video saved me a ton of time, the service program doesn't describe it well at all and it's literally a hair close from coming out but won't happen unless you do it the way you showed
I just did this today at work. Man what a pain in the fucking ass bro. This one kicked my ass. Injectors were ordered from the dealer so they all came with the seal and oring installed
Took mine out and cleaned them wasn't easy at all.but I got it done a lot of time just getting the rails out.the little clip on top of the injector hooks to the cups on the rail.
Thank you for your video. To install the injectors do I need to install the injectors and then the harness and the fuel rail afterwards. What is the order? Thank you very much.
Is there a way to adjust the timing without marks? I took the chain out and my stupidity allowed me to turn the the sprocket s individually, which turned the cams. Now I have no idea where I am at. Call me an idiot because I am. 2015 Chev malibu 2.5
@@martinv8750 th-cam.com/video/GBcBrAuC7tI/w-d-xo.html . This is a small video of my cams. Do you think i'm 180 degrees off on the timing ? Thanks for the helpt.
The injectors are coming up with the rail, head still in car. How do I disengage the injectors from the rail? You press something down in your video and it releases. Got a close up of that?
@@deividmendez7262 theres a notch in the start of every base that the injector moves into you just move the rail forward a little and it will come out.
no need to remove head! bank 1 pick rail up just enough for injectors to clear head. move aprox 1 inch to front of engine and rotate rail slightly. you will have to remove bank 2 bolts for clearance.
When replacing the injectors on these engines, has anyone tried the cheap set of injectors from eBay etc? I live is Australia and have this motor and got 6x injectors for around 100usd. I plan to sell the car soon so it doesn’t matter if they don’t last years and years?
Taking off the head is not of any help. The issue is getting the fuel rails outta the “V” with the heads in place. Who’s gonna pull heads to replace a fuel injector???
I have a big clip that goes on the rail and injectors. It’s metal and I couldn’t separate them until I got it out. My question is Now, how Am I suppose to put this back together...
Thanks for the video. This helped me finally getting the fuel rails out. What also helped me was reading the instructions again and following them by taking the fuel pressure sensor off the passenger side rail. This gave just enough room to finagle the driver's side rail out.
Thanks for the Video I got the rail out but started to second guess how the injectors were in there because they are tight. This is super helpful you rock!
Thanks man, it was tight and this video saved me a ton of time, the service program doesn't describe it well at all and it's literally a hair close from coming out but won't happen unless you do it the way you showed
I know your pain all to well sir, appreciate the tips... Wish me luck.
I just did this today at work. Man what a pain in the fucking ass bro. This one kicked my ass. Injectors were ordered from the dealer so they all came with the seal and oring installed
yes pain in the ass 👍
Thanks for the video!
Hey thanks for this video, I'm literally getting ready to replace injectors in my 13 they just got delivered
Hi, how did it go?
Took mine out and cleaned them wasn't easy at all.but I got it done a lot of time just getting the rails out.the little clip on top of the injector hooks to the cups on the rail.
i know it a pain
@@martinv8750 sliced the whole top of my finger while trying
Did you have to put it back in time after this process
How does one depressurize the fuel system? Impala is a DI engine so it runs with higher pressure.
Yo sacado muchas veces y nunca desmontó la cabeza
It’s so ease first remove the one from bank 1 then when you put it back first install the bank 2 it’s how works
Thank you very much !
Thanks
Thank you for your video. To install the injectors do I need to install the injectors and then the harness and the fuel rail afterwards. What is the order? Thank you very much.
hi yes first the injectors and the harness after
looking at your video chevy and gmc have done some stupid like this with the injection system.
Is there a way to adjust the timing without marks? I took the chain out and my stupidity allowed me to turn the the sprocket s individually, which turned the cams. Now I have no idea where I am at. Call me an idiot because I am. 2015 Chev malibu 2.5
no tou need to line up the marks with the chain look on google they should heve a picture of the marks
@@martinv8750 th-cam.com/video/GBcBrAuC7tI/w-d-xo.html . This is a small video of my cams. Do you think i'm 180 degrees off on the timing ? Thanks for the helpt.
Same motor as the 3.6 Chevy Camaro right ?. How hard is it to move the head ?
Bro I remove the fuel rail put the injector is stuck down there any tips to help me remove it?!
Hi what you mean stuck?
The injectors are coming up with the rail, head still in car. How do I disengage the injectors from the rail? You press something down in your video and it releases. Got a close up of that?
you have to separate the injector and rail just push down on the injector
its hard its not easy
v so there is no tab or anything I'm pushing to release the injector from the rail? Thanks a bunch
@@dankrier2666 no tab just push down on the injector its hard .....
It’s cast iron. Replace with 11/32 Sbc 2 piece keepers
Sbc keepers for 2 piece retainers
For so reason mine has steel clips holding them to the rail.
They can be removed in one piece. Its difficult but it can be done.
How so?
I yes you’re right. I took mine off with it all together. Took me about 10 minutes to remove both of them. It’s a little tricky but it can be done
@@deividmendez7262 theres a notch in the start of every base that the injector moves into you just move the rail forward a little and it will come out.
Did you replace the high pressure fuel line? Where did you buy your sizing tool?
snap-on , yes a replace the line .
I use the original lone and it worked perfectly fine
no need to remove head! bank 1 pick rail up just enough for injectors to clear head. move aprox 1 inch to front of engine and rotate rail slightly. you will have to remove bank 2 bolts for clearance.
just remove the fuel rail bolts no need to remove the heads ...
He said at the beginning that the head is just removed to make it easy to show you
👏👏👏
When replacing the injectors on these engines, has anyone tried the cheap set of injectors from eBay etc?
I live is Australia and have this motor and got 6x injectors for around 100usd.
I plan to sell the car soon so it doesn’t matter if they don’t last years and years?
Taking off the head is not of any help. The issue is getting the fuel rails outta the “V” with the heads in place. Who’s gonna pull heads to replace a fuel injector???
What's the name or part # of tool used to replace o rings
Injector Seal Installer Sizer EN-48266 try this one
I have a big clip that goes on the rail and injectors. It’s metal and I couldn’t separate them until I got it out. My question is
Now, how
Am
I suppose to put this back together...
the metal clip you just push it and thats it buy the new injectors seals you should jet the metal clips don't reused them buy new
Do you need tool puller to take out the inyector is hard to take out
Not true,because they have a alighment clamp,he removed all the clamp,you need to fight to install them qith atleast two person,removing them is easy
My mechanic charging 250 and I know why lol.
Having so much trouble getting the fuel rail out
i know its hard try two long screw driver hold the injector and pull up the reail with the other one
Martin v to get the injectors out did you just pushed them out or did you do something else?
@@cipheresp9643 just push them out
Martin v any tip on getting the injectors off because I am afraid to break them if I push too hard or where should I hold the injector from
grave them from the metal piece your gonna replace it any way it between the injetor and the tube...
i take them out all the time in the vehicle without pulling the head
I was able to take it off no problem!
What a crap design... 💩
Thanks