Yes, you are correct. I love seeing a waveform on the CRT. And knowing that that very waveform is what I am actually seeing. And not processed and printed to an LCD before I am able to work with it.
sweet video... BK test equipment has been around for a long time and works well..... thanks...:) great resolver info... is there the hobby version ab-ultraware servo software?
Dear Mr Peepaw thank you for all your videos, they have been very helpful, I wanted to ask if you, I have a 3 Phase DC 24V servo motor, is there a good software to help me to to a report on the condition of the motor and help me to position the resolver at teh same time? I also have a Angle resolver used in a valve to let me know at what angle of opening is the valve do I tune it the same Cosine maximum wave and sine flat? thank you in advance.
Hello mr.McDonald! thanks a lot for yours videos, it very useful, and I have a couple of question about resolver. 1. Which connection of the motor - Y or Triangle ? 2) If you put +5V to the U phase, and GND to the V phase, and 2(a) is it works on both Y and triangle motor? 2(b) do I have to set signal COS in MAX, or signal SIN in MAX position by oscilloscope 3) what if I make wrong place SIN and COS position? Will motor work? 4) What if my drive doesnt show any errors, but there are not enought torque on the shaft?
You are very welcome. I am glad that you enjoyed my video. Troubleshooting and repairing electronics has always been interesting to me. And I always enjoy seeing other folks who share an interest in electronics. Thank you very much.
If we set 7 volts in the primary coil, what will be the peak voltage in the cosine coil at angle zero Is it 7 volts or less? The rule to find out the peak voltage at angle zero is as follows (peak potential of the cosine signal = voltage on the input coil x cosine of angle sita) (V cosine=Vr x cos cita)
Great on getting a new oscilloscope. My two best work friends are my oscilloscope and digital-multi meter. HaHa. Thank you very much for watching my video.
Hello sir. Kindly sir send me the video of lenze drive 9200 or other change the parameter and save the drive through of global drive software. Thank you very much
If we set 7 volts in the primary coil, what will be the peak voltage in the cosine coil at angle zero Is it 7 volts or less? The rule to find out the peak voltage at angle zero is as follows (peak potential of the cosine signal = voltage on the input coil x cosine of angle sita) (V cosine=Vr x cos cita)
Thanks for your labor.
Great video. For these kinds of things I prefer using my analog scope. It “feels” better.. no idea how to explain that but I think you get it.
Yes, you are correct. I love seeing a waveform on the CRT. And knowing that that very waveform is what I am actually seeing. And not processed and printed to an LCD before I am able to work with it.
sweet video... BK test equipment has been around for a long time and works well..... thanks...:) great resolver info... is there the hobby version ab-ultraware servo software?
Dear Mr Peepaw thank you for all your videos, they have been very helpful, I wanted to ask if you, I have a 3 Phase DC 24V servo motor, is there a good software to help me to to a report on the condition of the motor and help me to position the resolver at teh same time? I also have a Angle resolver used in a valve to let me know at what angle of opening is the valve do I tune it the same Cosine maximum wave and sine flat? thank you in advance.
Hello mr.McDonald! thanks a lot for yours videos, it very useful, and I have a couple of question about resolver. 1. Which connection of the motor - Y or Triangle ? 2) If you put +5V to the U phase, and GND to the V phase, and 2(a) is it works on both Y and triangle motor? 2(b) do I have to set signal COS in MAX, or signal SIN in MAX position by oscilloscope 3) what if I make wrong place SIN and COS position? Will motor work? 4) What if my drive doesnt show any errors, but there are not enought torque on the shaft?
Hello.. Thanks for this video and is it possible to convert the signal in to angle value..
i love this guru
I like the X-Y mode. I’ll try that tomorrow! 👍🏻
Excellent video greetings from Venezuela
Thank you very much. I am glad you liked my video.
alexs castellano ㅈㅅ.ㅅ
0ㄷㅇㅈㅅㅈㄴ.ㄴㅈ
Please add a video for aligning the Ac Tacho generator with servo motor.
Good evening!
Do you have a video that teaches how to synchronize an encoder with the Siemens motor?
does resolver need calibration?
Can i see the diagram how your wired up the sin, cos and excitation ?
Hello Sir! from this test, how do i understand whether the motor's resolver tighten position is okay or not? Please ans me Sir .
your channel content is very rare thank you so much for sharing that with us.
i hope i find a way to contact you some times for some help.
Thank you so much, awesome.
You are very welcome. I am glad that you enjoyed my video. Troubleshooting and repairing electronics has always been interesting to me. And I always enjoy seeing other folks who share an interest in electronics. Thank you very much.
maravilha muito bom ta de parabes
Hi, how i can find a "dead motor postion" in Ac servomotor? Same as dc with dc power supply? Its posibble?
Thanks for yours great's helpful videos
If we set 7 volts in the primary coil, what will be the peak voltage in the cosine coil at angle zero Is it 7 volts or less? The rule to find out the peak voltage at angle zero is as follows (peak potential of the cosine signal = voltage on the input coil x cosine of angle sita) (V cosine=Vr x cos cita)
excellent.
Thank you so much
Thank you sir 😊😊
I would like to email you with a few questions if you don't mind.
Thank you boss
thanks for your video,,,,
can you help me, please send me your picture diagram installation during calibration
I've just got an oscilloscope and going to have to borrow a motor to try this
Great on getting a new oscilloscope. My two best work friends are my oscilloscope and digital-multi meter. HaHa. Thank you very much for watching my video.
Dear Mr Peepaw, do you have the electrical diagram about it ?
th-cam.com/video/idPqWsfrolU/w-d-xo.html
Greate video. I want to open small servo motor servis in Poland. It is posibilit support me?
Hi, when r u open?
Can anybody give the data of this resolver company name LTN model RE21-1-d64
Hello sir. Kindly sir send me the video of lenze drive 9200 or other change the parameter and save the drive through of global drive software. Thank you very much
Hi,,, do you resolv your problem ? Do you have the procedure of test to resolver ?
If we set 7 volts in the primary coil, what will be the peak voltage in the cosine coil at angle zero Is it 7 volts or less? The rule to find out the peak voltage at angle zero is as follows (peak potential of the cosine signal = voltage on the input coil x cosine of angle sita) (V cosine=Vr x cos cita)