Needle Scaler UPDATE

4 Days REAL use in on the inexpensive needle scaler and its showing NO signs of ANY problems or issues for usage. So for $40 how can you go wrong?

[@voidisyinyangvoidisyinyang885]

I've nominated this vid for an Emmy due to the high class editing.

[@rcguygarage]

😂🤣

[@voidisyinyangvoidisyinyang885]

This vid made me feel better about just getting an electric scaler!! It really does remove rust very well - better than a wire brush. thanks

[@vitix5906]

Excellent visual representation! I think this along with a chipping hammer and a heavy wire brush grinder all working together will be my solution for my trucks frame resto... I was looking at that very same tool on amazon....SOLD!

[@mongomay1]

A air chisel helps break the heavy stuff, then needle scale.

[@rcguygarage]

BFH works too😉👍

[@Cjinglaterra]

We used these extensively in the Navy. I bought one from Harbor Freight to take care of some frame rust.

[@rcguygarage]

They work as expected! Not the best but get the job DONE

[@juliogonzo2718]

Guy I worked for gave me one 6 years ago. Has sat unused since. Need to get scale off a scabby used engine I'm swapping in so I can paint it. Finally going to get used!

[@tiredoldman5329]

Nice vid. I just got the same one. haven't used it yet though.

[@jeremylister89]

🇬🇧 UK here!
Are the needles specially hardened? Made of special steel or even something like tungsten?
Tried hammer before and got bits in my eye 😁

[@rcguygarage]

Not soft but no need replacement eventually or just buy a new one

[@manbearkremer]

I wish I knew this tool existed, would have made cleaning up my axles 10 times easier

[@rcguygarage]

Definitely can make quick work of certain parts and then again the original old school way still works in other areas faster 🤣😂👍

[@robertjohnson774]

What type or brand of paint did you put on the knuckle?

[@rcguygarage]

Rust-Oleum 2x Ultra cover Paint & primer gloss black

[@SpaceFrawg]

How much pressure do you have to put on the tool?

[@rcguygarage]

The tool just needs to contact the surface so very little to none

[@lawrencenisbett7579]

You've sold me to it, and I'm a hard sell!

[@engjds]

Dont know man, to me it would be better with a flap disk for that.

[@rcguygarage]

@@engjds flap disk can't get into the back side crevices. This was to just show what it does not an actual viable use every time👍

[@engjds]

@@rcguygarage Fair enough, they do look handy, especially for bad welders like me haha.

[@aceorace]

What's the minimum size compressor needed for this?

[@rcguygarage]

5 scfm 20 gal just know that if your recovery time on pump is slow you'll kill your pump. This is with ANY high air usage tool. USE WATER SEPARATOR

[@pappaclutch3266]

So this works better then a good angle grinder and heavy duty wire wheel?

[@rcguygarage]

Yes but keep in mind I was showing the usage of the tool. A good size hammer can take off the big stuff

[@rcguygarage]

This will also get into those nooks

[@Techdyno-cw3ow]

You can do it faster with some Oxy acetylene

[@shelbyfz07vtec65]

Is it loud?

[@rcguygarage]

Wear ear protection if you value your hearing😜👍💯👊

[@freddierextagacay8861]

@@rcguygarage 😂😂😂

[@JoDaddysGarage]

Slooooooowwww moooooooo.....

[@rcguygarage]

Yep 👍🤣😂

[@rcguygarage]

It's the best