10:13 how thre hell did you remoeve the engine without taking apart the hull? I already unscrewed those 4 outer bolts holding the thinner piece of metal, but I still have 4 bolts that are on those raised metal mountsa under the engine with screw holes.
On my old 550 I sucked up a rock and a whole new performance jet pump already assembled was easier than repairing the old one and it’s hard as hell to get them out on some skis. My dad and I were out there with a crowbar going full send
I got a Polaris SLT 700 and it needed new fuel filters and a battery. After that, it started after I put a little gas in the carburetors. A week later I tried again and it started right up. Then I took it to the lake and it wouldn't start. I tried for 10 minutes to start it and it turned and turned until I thought I might kill the battery. Then I looked under the seat to see what I could find and the ground cable must have got really hot because the the insulation completely melted off. Any thoughts???
I’ve got a 1998 polaris slth 700 that was working fine then on the water the other day it didn’t want to start and ran my battery dead so I jumped it and it ran great the rest of the day until I turned it off. I went to start it and only got a click,click. Took it home put the battery on the charger and I still only get a click, click. I tried to by pass the relay with a screwdriver but the starter didn’t turn over. The breaker isn’t tripped and both fuses are good in the box. Any suggestions? Thanks
I just purchased a 1997 SLX IT HAS 3 CYLINDERS. I HAVEN'T got the title yet but before I spend a lot of money on it I'd like to know how many CC'S it is
Good job on the videos. I am looking at buying a jet ski in order to remove the engine and put it into a 15 or 16 foot boat. Do you have any advice on removing the engine and connections so they're easy to remount? I've never worked on the Jet ski before. Thanks
my name is norm begin just bought a 98 polaris slt 700 no compression in the back cylinder so I took it apart my question is where is the best place to find a cylinder or jug piston and rings looks like that cylinder got hot and the ring broke off and grooved the cylinder wall.
I am Mary and have been watching some of your vidoes all day however none have covered just what i need to know. i have pulled the plugs and #1 looks fouled #2 has a grey build up #3 looks like it has never been used, I could use some help to know what it may be and what to do it runs kind of slugish
i have polaris slt700 set. no spark but compression and everything else is good. also a project slx 650 with a cracked center piston and trying to get that and 1 of the sl700 running, then sell the rest. maybe anyone have parts for trade or sale?i am in centra; florida sebring area.
Another great ski destroyed. It takes ~1 day to rebuild a 700 domestic engine.
Did you see the front end
10:13 how thre hell did you remoeve the engine without taking apart the hull? I already unscrewed those 4 outer bolts holding the thinner piece of metal, but I still have 4 bolts that are on those raised metal mountsa under the engine with screw holes.
On my old 550 I sucked up a rock and a whole new performance jet pump already assembled was easier than repairing the old one and it’s hard as hell to get them out on some skis. My dad and I were out there with a crowbar going full send
I got a Polaris SLT 700 and it needed new fuel filters and a battery. After that, it started after I put a little gas in the carburetors. A week later I tried again and it started right up. Then I took it to the lake and it wouldn't start. I tried for 10 minutes to start it and it turned and turned until I thought I might kill the battery. Then I looked under the seat to see what I could find and the ground cable must have got really hot because the the insulation completely melted off. Any thoughts???
I’ve got a 1998 polaris slth 700 that was working fine then on the water the other day it didn’t want to start and ran my battery dead so I jumped it and it ran great the rest of the day until I turned it off. I went to start it and only got a click,click. Took it home put the battery on the charger and I still only get a click, click. I tried to by pass the relay with a screwdriver but the starter didn’t turn over. The breaker isn’t tripped and both fuses are good in the box. Any suggestions? Thanks
I need rubber gunwhale bumpers still have them,mine are weather cracked?snookie pa.
I just purchased a 1997 SLX IT HAS 3 CYLINDERS. I HAVEN'T got the title yet but before I spend a lot of money on it I'd like to know how many CC'S it is
Got a 2001 Polaris slh 700 runs like a dream out of the water won't run in the water any ideas
Good job on the videos. I am looking at buying a jet ski in order to remove the engine and put it into a 15 or 16 foot boat. Do you have any advice on removing the engine and connections so they're easy to remount? I've never worked on the Jet ski before. Thanks
You wouldn’t happen to still have the CDI, primary and secondary coils would you?
my name is norm begin just bought a 98 polaris slt 700 no compression in the back cylinder so I took it apart my question is where is the best place to find a cylinder or jug piston and rings looks like that cylinder got hot and the ring broke off and grooved the cylinder wall.
on the polaris sl700 head wich way does the large gap on the head face??? there is a small gap on one side and a large one on the other.
Any idea on how to remove the fuel tank on a Polaris slt 700?
Do you still have the oil pump by any chance?
I am Mary and have been watching some of your vidoes all day however none have covered just what i need to know. i have pulled the plugs and #1 looks fouled #2 has a grey build up #3 looks like it has never been used, I could use some help to know what it may be and what to do it runs kind of slugish
Where are the spark plugs located? Does anyone have the time he shows it?
how do you remove from the shaft?
@dragracer3
I don't think so.
How do run a break in on new cylinders. Im doing an engine rebbuild
Where do you order your parts from
How can I stop the engine from turning in order to remove (unscrew) and replace the coupling? Thanks in advance.
PL-700
3 years to late but a rope down the spark plug hole.
@upallnight888
The things that are on the hood itself are bent.
do you sell parts if so how can i get in touch with you just bought a polaris hurricane fro my boys and need a few items
Anyone know how to change starter on Polaris 94 SLT 700 ans location?
Are you interested in another 700 slth 98? Still runs
where ata?
Hey, I have a Polaris 780 STL, I am looking for a motor, do you have any motors that you are selling?
i have polaris slt700 set. no spark but compression and everything else is good. also a project slx 650 with a cracked center piston and trying to get that and 1 of the sl700 running, then sell the rest. maybe anyone have parts for trade or sale?i am in centra; florida sebring area.
If you want to sell the front hinge hardware assembly for the front hood let me know.
check out green hulk dot net. They have a forum on how to break it in.
No title in texas means junk
you should upgrade to better jetski's