Auto Hand Wash system using Arduino. GO CORONA | I2c The Master
ฝัง
- เผยแพร่เมื่อ 2 เม.ย. 2020
- #FIGHTCOVID19 #COVID19 #DIY#Autohandsanitizer
How to make Auto HandWashing system using arduino.
By reducing physical contact, an automated handwash keeps virus from spreading around in communal areas.
ALL SOURCE CODES HERE:
github.com/NirmalKnock/Auto_H...
REQUIREMENTS BELOW:
1).Ultrasonics sensor:
2).Arduino UNO
3).Relay module 5v
4).connecting Wires
5).water pump
all music credits goes to:;
music in this videos
Learn more
Listen ad-free with TH-cam Premium
Song
Firefly
Artist
Jim Yosef
Licensed to TH-cam by
AEI (on behalf of NCS); UMPG Publishing, LatinAutor - UMPG, ASCAP, Featherstone Music (publishing), BMI - Broadcast Music Inc., LatinAutor, and 12 Music Rights Societies
Listen ad-free with TH-cam Premium
Song
Cloud 9
Artist
Itro & Tobu
Licensed to TH-cam by
ASCAP, UMPI, and 8 Music Rights Societies
Sir.. first a fall thanks a lot for the video and descriptions, it does work exactly how it has shown on the video. However, i have faced one problem while giving a try with sanitizer instead of water in the bottle, it does not come out through the pipe whereas water does not have any issue. I would be thankful if you advise me your idea with me. Thank you in advance.
i think sanitizer density is high , so pump can't able to push out , so try with other pumps, with higher power ratings.or try with lower density hand sanitizers.similar to water type
👏🏻👏🏻👏🏻 super bro we need more videos like this useful update 😎
Sure 👍😂😂
Isse ham 12v ka pump chala sakte hai kya
hy I made your project automatic water pump but it is only working when I connect Arduino with laptop I have made connection according to digram can you please tell what is wrong
Super nirmal keep it up
Thank you so much
Can in decrease the water timing as using it for alcohol sanitizer?
yes, you can , i mentioned on the codes
Please can you explain relay connection.
I dont understand to your given relay circuit diagram connection.
Plsase help me
ok,pls give me time ,i upload the real schematic circuit diagram in description.after i uploaded i will inform you
i do have made the same but have used L298n instead of relay module
Yes you can
what volts the water pump?
Depends on the Pump you have. I bought a 5v pump, so a max of 6v to 7 v is enough.
Sir plz help me ..i m connecting all the connections in proper way, sensor is working also ....blink light in realy module for 10seconds...but..motor is not strart......can you help me plz??
same issue i'm facing
Awesome
What program is that actually?
is based on the c program using arduino microcontroller ans sensors.
Thats awesome. But please I will like to also see the simulation and the software used. Thanks
I didn't make any simulation for this project, just doing a hands-on, all the components and diagrams in the description verify that, still any doubt, just ping me again.
Can we add a time limit for the flow in the code......plz explain sir
Yea , you can decrease or increase the flow , I mentioned in the code
Can we add timer in this instead of ardino uno can we use nano
yes you can use both for this project,when using nano, select the nano in boards manager
@@i2cthemaster82 tq bro let me try it tomorrow and i will review you tq for reply
Bro can u give the relay connections for single channel relay i am not understanding your circuit connection
@@supreetbengeri6326ok i will send , pls wait, meanwhile setup other activities
I am eagrly waiting for it bro
sir you give power with cable and battery both
i used battery for motors and cable to power up the arduino
Can one power be used for both......plz explain sir
@@tjentertainments2611 Yes, you can power up, but the problem is after the voltage is down, the motor can't run at full load.
nice thank you
Thank you too
can u make a fingerprint door lock with alarm system
in future i will try that
Can I use single channel relay bro
yes,you can use
Bro i have done all the connections,when i gave the power LED lights in arduino and relay module(one red light only) turned on..when i move my hand to the sensor the red light of the relay module turned off for some seconds and turned on again...but the motor didnt worked...please help
try with external power supply for relay ,and if the the problem repeats, contact me again☺
@@i2cthemaster82 how to give power externally to relay module?
@@arjun9791 use battery to relay module ,power pins are there like VCC and GND
@@i2cthemaster82 then how will be connections between relay module and arduino?
Can you pls send me a diagram of this if i give a mail to you
Plz send circuit diagram with audreno and ultrasonic sensor and relay and battery
its on the link i given in the description, and you can also use single channel relay
@@i2cthemaster82 plz send circuit diagram adding ultrasonic sensor there in discription it is only showing of audreno relay motor and battery
After making all connections according to diagram the pump was running automatically. Can anyone help me with that
check with your connections and power supply
May i know another option to power up the arduino please ?
using the Vin pin you can power up the arduino
I2C The master with 9v battery ??
@@vrajshah5743 yes , you can use
I2C The master thank you sir 😀
is it okay to use 12V water pump?
Yea, you can use it with the same config.
@@i2cthemaster82 but then i need to change the battery to 12V instead of 9V if i use 12V water pump?
Can you share the Circuit Diagram
that in github page, check the link that is given in description
Bruh , motor not working , please help me. I have mailed you.
Battery how many volts sir?
less than 12v is better
VERY GOOD VIDEO BUT HOW TO REDUCE THE TIME OF COMING HANDWASH
in this code i mention the timing limits you can change that in terms of milliseconds
My water pump is countinous going on....plzz tell me how can I resolve this
First check the wiring to the motors from arduino and then check ultrasonic sensor wiring....when your prblem not solved.
pls send the source codes and wiring as in ur project @
email: nirkamalarcot12345@gmail.com
i will check that,
Sir it work properly as shown in vedio when I give power thought the port from where we burn code.but if I give power of dc jack of aurdino motor countinous run without sensing the aurdino plzz explain why this happens....
check the voltage level given to sensor,.when problem on the sensor voltage ,some times the system may goes to unstable..try ..
is problem resolved?
Can you help me the code and connection please? Thanks
All code are available in description use can use it..if you have any questions ,let me know again.
I have do same with IR proximity sensor will you help me with circuit diagram and source code 🙂
yes, i will make that
@@maheshshinde3845 ok thnk you
ok .i will make soon ,after i give my GitHub link to you
@@maheshshinde3845 Ok i will make soon and i share my link to you
@@i2cthemaster82
Thanks ! I am waiting 🙂
Can you send the code here bro
all codes are in description area..
Does this code works really
yes it works.if you have an problem ,then contact me
Can I get the circuit diagram ?
Tomorrow i will send you ,definitely
@@i2cthemaster82 okay can u ASAP
@@aaminasubuki9071 github.com/NirmalKnock/Auto_Hand_wash_system
@@aaminasubuki9071 I uploaded new diagram,still have any doubts, let me know.
Thank you so much