how do you adjust the handbrake on the 2017 same as yours no rubber grommet to adjust i assume thats for shoes but the one under glove box hasnt helped much with new brake pads in rear
If it doesn’t have shoes then to improve the handbrake, under the centre console where the handbrake lever is you will find a 10/11mm nut on the cables which you can tighten
If you can't get the pads set correctly using the notches at 12 and 6 a trick is just to grind the notch off the pad, the notch is there to stop the piston turning when you apply the handbrake but in reality they never do this. If you can get better tolerances without the notch then just remove it.
@@owensautotips Been doing it for 40 years never had an issue, sometimes you have to especially with pistons that only have 2 notches at 12 and 6 where a half turn one way or the other is not just right with cars that are difficult to get handbrake adjustment perfect.
Уши колодок мажутся если нет пластин посадочных,на этих пластинах они должны быть сухими,смазка быстро затвердеет от пыли при износе колодок и они опять начнут клинить,испытывал и со смазкой и без неё,на сухую приходится реже разбирать чистить
do i need a special windback tool for the caliper piston, or does the cheapest ones work?
Cheap kit of eBay/Amazon will do
@@owensautotips thanks mate!
Will pushing back def not work if I don't have a windback kit? I used to push back on my older car.
Do you not take the lid off your brake fluid container?
Yes buddy, I apologise for forgetting to add it in
how do you adjust the handbrake on the 2017 same as yours no rubber grommet to adjust i assume thats for shoes but the one under glove box hasnt helped much with new brake pads in rear
If it doesn’t have shoes then to improve the handbrake, under the centre console where the handbrake lever is you will find a 10/11mm nut on the cables which you can tighten
thanks done now i adjusted but was not as it was before brake pad change i guess it will need to bed in first@@owensautotips
is all the parts are same on 2017 plate number?
Should be buddy
I found the problem was the caliper piston was meant to be set at 12 and 6 o'clock so the notch in the piston fits the notch on the pad
Awesome buddy, good job 👏
If you can't get the pads set correctly using the notches at 12 and 6 a trick is just to grind the notch off the pad, the notch is there to stop the piston turning when you apply the handbrake but in reality they never do this. If you can get better tolerances without the notch then just remove it.
@rodpanhard yes grind of something that was intended to be there from factory. Don’t be that guy
@@owensautotips Been doing it for 40 years never had an issue, sometimes you have to especially with pistons that only have 2 notches at 12 and 6 where a half turn one way or the other is not just right with cars that are difficult to get handbrake adjustment perfect.
@rodpanhard I’ve been doing it 10 years and never have I ever ground the pads down to get it to fit
I need to contact you about this car as I have it do you have a email or something
@@Lhsthe1 in what way do you need to contact me about it
@ I need information about my hyundai i30
@Lhsthe1 then ask away
@ my rear brake pads don’t fit after driving it makes a growlin house I wonder what frame I need to change it because I think it’s a frame issue
The brake pads that are supposed to fit don’t fit do you know what frame I need to buy the name of it
Уши колодок мажутся если нет пластин посадочных,на этих пластинах они должны быть сухими,смазка быстро затвердеет от пыли при износе колодок и они опять начнут клинить,испытывал и со смазкой и без неё,на сухую приходится реже разбирать чистить
I work for dealer and this is dealer process
Useless video why not show how to wind back callipers…
😂😂😂 go learn
“We are going to use a calliper wind back tool” listen to the video.