วีดีโอ

Hello thank you for the tutorial on changing the handle that does not work but my question to you is if the sensor is working but the handle still doesn’t unlock the door. I also use the key and though the key turns the door still refuses to unlock should I still changethe handle would that help my problem thank you for your response and thanks again great video

No diagnostics? Just swap parts?

hooa friend, do you have the cylinder head tightening for the H4bT engine, I'm building one and I can't find it anywhere 😔

Well done for this , regards

What about the stupid car computer? Any codes that must be re-entered? Will the radio still work after the battery was disconnected?

Still sounded horrible

Hello, which engine oil will you recommend for a hyundai ix35 2011?

Hi, thanks a lot. Very clear video and instructions! One question. Which gasket maker should be used? Cheers

Don't you have to re seat the injecor wells

tak

How did yu adjust it?

@owensautotips - no idea why you didn't drain the diesel to a container to check if there actually was water in the fuel. As some of the questions below (and is the case with mine) it's often an erroneous message to do with wiring/earthing and nothing to do with water. I changed my filter (still had original on a MY13) and sensor and was still getting the error, so going to investigate the wiring. In terms of resetting the error message, if your OBDII tool resets any errors, then it's likely it will do this one - mine is a £50 one from Autel and does almost anything, so it's not about the price.

It's all fun and games untill the car run you over or the very least run over your foot , if one of your colleagues shifted the car in any gear for whatever reason or attempted to retreive tools or stuff in the passenger seat / floor and leaned over the gear knob and knocked it into gear, assuming weak or not engaged parking brake. Stay safe out there. Best of luck

Do you have any suggestions for me: My santa fe 2015 trunk SOMETIMES wont open. When it wont open, the button press doesnt make any noise (like the latching noise). Randomly it will start working again and the latching noise will return of course. My mechanic has not been able to replicate the issue as my car is gaslighting me and decides to work every time i take it to the mechanic. Any ideas? Is it the actuator or the switch? Or something more? Thanks fir your video and your time reading this 😊

How do you know when the issue is the button and not the actuator for the machine on the latch? The door wouldn’t close because the latch wouldn’t lock, so I slammed it a bit harder and then the latch stuck but now it won’t open. My thought is something is wrong with the lock mechanism but if the button isn’t working to open the latch, then maybe that’s the issue too. Thanks for this video, it’s the closest thing I can find to my specific issue!

We need definitely more videos like that. Greets from Germany

Mechanic mentioned timing chain replacement, rockers and tappets along with head gasket repair. Engine has 35000 miles. Would you recommend additional work?

Much is the all the cost to do the timing chain on ep3

Hi I am facing same issue, heavy, insane oil consumption for the 1.2 puretech engine. and recently while trying to accelerate near signals after a complete stop i am able to see white smoke as well. is it good to repair or replace the whole engine ? because repair seems to be costing around 2500 to 3000 euros and new engine including labour is costing 5000 euros in total. what would you suggest ? my car millage is 1,70,000 km already.

Great videos and info! Thanks for the work. Just had 3rd motor put in and still the same "rattling/grinding" noise. Car shop insisting noise not coming from reduction gear. Should we continue to fight the service or just give up? 😅

Do the spark plugs need to face a certain way once tightened?

Brilliant video - my son's discs were a little harder to remove that the video suggested but with "some encouragement" from my attitude adjustment tool (FBH) we were able to get it done in an hour (both sides) - thanks for the expert guidance - it all made much more sense when we got started having watched your video first.

Great video for me as I'm about to either adjust or replace the brake light switch on my 2011 FD i30. There is no earth wire running from the switch now as supplied new when purchased from Hyundai. Also in your video there didn't seem to be one on either. So I'm curious why you installed an earth wire when. you did the switch replacement? Is it required? Sorry if I missed something in the video that might have explained it.

Ford ecoboost 1.0

Hi! Has the tailgate's locking changed? It seems to be closing much tighter now, and I'm not sure it's good for the electric motors that power it.

youv'e got a very good variety of skills nice one

Hello, Thanks for the video. But is it absolutely necessary to enter the injector serial number with the case? Can we drive without this?

I didnt think you could turn ignition on witout engine on keyless start?

I've seen that you can either buy the whole assembly or Delphi bolt on pencil coils so retaining the original frame/mount but getting a well know brand for the same price as a generic whole frame. I assume that it's on the actual coils that will provide an improvement on ignition not the whole frame?

Ford wetbelt ?

I have compression of 6 bars in all four cylinders , timing chain is new but my car does not start

Is this diesel or petrol

Still can’t believe Honda made the stupid mistake of going for a wet belt. I’ll be keeping my 2007 1.8 Type S GT, 170k miles & the timing CHAIN has never missed a beat!

My 2012 Mercedes SLK-200 6-Speed Manual Does that too, not sure if it was bypassed or messed with it's safety switch or it doesn't have one at all LHD Car in Middle East (Could be due to our specs ?!)

for me the watterpump is wet but after 700km i lost middle of min max from my coolant :/

My 2000 reg mk1 mondeo turns on the button. Only 34k miles on the old girl

Thank you for this!

My 92 land cruiser catches first swing. 32years young.

I miss that!

My 08 touran

Hey buddy, I've recently replaced timing chain all 4 guides and new tensioner on my Rio. Due to rattle (worse from cold) Sounds 100% like timing chain rattle. After replacing all the parts the rattle is still there and I'd say it's getting worse. All Kia genuine parts used. Any ideas what can cause that? Do you know if these suffer with vvt pulleys making rattle noises? Or something like oil pump not creating enough pressure for the tensioner? Why are you changing the rockers and lifters, cant quite hear what you said in the video? Many thanks 👍

thank you for sharing

Whatif u dont program the injector

Wrong. Side opposite tension shouldn't have slack

long shot, have a 2018 ioniq that had a small bump in the front and has the same errors AEB and smart cruise faults, i know the emblem is damaged but could the radar unit behind be bent back to level and function correctly if it is just bent out of calibration ? (given there is no damage to the radar unit face)

🎉

My 2019 berlingo 😂

Great tutorial thanks! What year was this model? Mine is a 68 plate premium model.

Km?

Where is your garage location?