How to Snorkel your 2014-2021 Honda rancher, foreman, or rubicon!
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2024
- This video isn't the best step by step tutorial, but you will see all the steps to snorkel your 2014-2021 Honda rancher, the only other step for the foremans and rubicons would be to use a 3" test plug for your secondary airbox.
let me know what you think! I can also post up the readmit build and install from wild boar.
check us out on facebook and instagram @hondaboats
Electric grease.
1 1/2 inch pbc cuppler
5 1/2 pbc
1 1/2 inch rubber cuppler
4 ft of spa hose
1 1/2 inch to 2 inch rubber cuppler
2 inch Pbc 90
2 inch Pbc 45
However Tall you want snorkel 2 inches thick
id use abs instead of pvc its black and stronger also
Need a video on how to run vent lines
Haha I just realized that my brother is the camera man right now 😂
Can u please make a part list??
5ft 2” pvc pipe, 2 2” to 1’2 or 1’4 coupler, 1 inch spa hose buy like 2-3ft and cut it to needed length or longer, like 5 inches of 2” pvc to run from your boot to the pvc pipe then the coupler then spa hose then coupler and then the tall snorkel piece
And grease
What’s that Metal piece called
You need to quarter turn your glued connections to seal em
Thanks for the tip!
Hi there I have an rzr 800 and I snorkeled it and used ultra black and it did fine in the water but later on in week it ran like crap though water got in fuel so parked it and when I got home my throttle body was laying in the valley of the engine so I need to put ultra black on the throttle body ( both sides ) or does the rubber cupers keep water out
Same process for 2022 foreman?
Yes
Thanks going to do the 2021 520 like this
J espère que tu sais que ton débit d air va changé..Si tu veux pas qui s'étouffe a chaque foi tu va donné full gaz..coûte pas si chère le faire le setting..la tu va vraiment voir la différence..Si non good jobe
Part list for 3ft snorkel the coupler inch and exacts fits plz
Great video very helpful
Thank you!
Every time he cusses he had to do 10 up downs no matter where y’all are
what about vent lines?
What is the black silicone stuff?
Permatex Ultrablack
Vent line size!
5/32" and 7/32" for the gas tank vent
@@vesselpowersports what all do I vent out? Diff ? Brakes?
How you supposed to open the air box now 😂
Good question, we're now using airbox lid seals
Can you just make a material list please.
With the fuel injection u don't have to retune or anything?
nope!
Do you do anything to the 02 sensor?
No heat shield around the spa hose ???
correct!
That piece you put in the air box was that a 2in to 1/2 in
Its a 1.5" pvc coupler, fits in the airbus perfect!
@@vesselpowersports is the 420 airbox the same as the 520 airbox?
Piece of aluminum for the bracket?
1/8th inch by 3/4" aluminum flatbar
You live in Louisiana?
Florida
do you have to dialetric grease all your plugs? or can you just run it
U said it, was thinking same thing,fuck might as well I've Takin min apart before a few times, if ya want it to last over kill every thing lol 😂 imma do it on mine
It would be best to so the plugs dont get corroded over time.
How long was the the pipe from the
1.5x2incg rubber boot to the 90 ?
about 4 inches
will this work on a ‘13?
Will this setup work good on a 2013 rancher?
For the most part yes, unsure of the airbox boot size though!
@@vesselpowersports bet
what seal y’all used
PVC glue for pvc and black permeated rev for rubbers and airbox
Y do u grease the lid
Seals the lid without having to use silicone
I’m scared to do my sons bike
It's a honda! you'll be alright
Did u use rtv or silicone on the air box
Black rtv
Were did you get the flex tube what size is it
Ace hardware 1.5" spa hose
Hondaboats thx
Shit helps a lot
Thank you!!!
Where you get the hose from?
Ace hardware
How much does it cost
How did you bend the bracket?
Used a vice and made 4 90° bends
I’m just too scared to take apart my whole 4 wheeler
Dangg
Whats the purple stuff
pvc cleaner
pvc primer
What type of clean is that 😂
You lost me at the spa hose
Why would you hard pipe your snorkel? These kits can be removed in once piece all through the front rad cover
@@vesselpowersports so can my homemade one with a couple rubber couplings.
No filter oil??
Did we not spray any? can't remember lol but for filter oil I usually use K&N
Do you rtv the inside as well?
On which part? the airbox?
What grease did you use on the air box lid
dielectric grease
@@vesselpowersportsdid you seal it with ultra black
Where did you get the tires?