i hope this isn’t a dumb question. but i’m trying to take out the nut holding the clutch on. & the whole clutch just spins freely. how did you get your clutch to lock in to take that nut off? any help will be appreciated.
Hondabond or grey rtv. And the clutch basket i just go until tight, ans the centrifugal clutch you tighten it up where there is just a little back and forth movement as you see in the video. Thats how i do it, im not sure on torque specs
what happens if you overtighten centrifugal clutch. I just watched this video after I did mine to verify everything the only thing I did differently was just tighten the centrifugal clutch and didn't check for playm reguard less where the gears mesh together I had the slightest bit of movement so I'm thinking it may wear some stuff down but be ok as I drove it amd everything seems fine.
Hey buddy I have a 2014 420FA1 , auto -esp .. sra is reduction same has 29.5 sassy.. clutch is slipping now don't know what in it now gr, can I count teeth, cause it may have gr in now, do you know teeth count...35, 53, thanks
@@vesselpowersports Ive got a 520 Rubicon and want to run 29.5" Assanators without a gear reduction... do you think it'll get bogged down or can it spin them pretty good
i hope this isn’t a dumb question. but i’m trying to take out the nut holding the clutch on. & the whole clutch just spins freely. how did you get your clutch to lock in to take that nut off? any help will be appreciated.
Hold it tight with your hand and a rag
How long did you take to put it back on and completely finish
What are you sealing the front case with?
Also what are the torque specs for the nuts holding the clutches on. Looking to do a GR soon.
Hondabond or grey rtv. And the clutch basket i just go until tight, ans the centrifugal clutch you tighten it up where there is just a little back and forth movement as you see in the video. Thats how i do it, im not sure on torque specs
How did you know when to stop tightening the clutch basket. The one with the one way in it that’s why I haft to change out on mine
left hand thread are right hand thread on the 27 mm staked nuts
not sure which is which lol normal thread, righty tighty lefty loosey haha!
Do you gotta pull the motor when doing clutches? 10 rancher 420? And does a clutch kit really do anything?
I’ll be at Boggs Halloween weekend,would like to ride with you some
Sounds good, get up with us out there!
what happens if you overtighten centrifugal clutch. I just watched this video after I did mine to verify everything the only thing I did differently was just tighten the centrifugal clutch and didn't check for playm reguard less where the gears mesh together I had the slightest bit of movement so I'm thinking it may wear some stuff down but be ok as I drove it amd everything seems fine.
Wish you were in Hawaii I’m looking for someone to do my 2016 rancher sra
Fly me out! ill do it free of charge lol
You said lift up on the shifter what if it's a automatic
Gracias. Men saludos desde México
Hey buddy I have a 2014 420FA1 , auto -esp .. sra is reduction same has 29.5 sassy.. clutch is slipping now don't know what in it now gr, can I count teeth, cause it may have gr in now, do you know teeth count...35, 53, thanks
Not sure, does your primary gear look welded or have reaction boss on it?
Hey buddy thanks for responding I've been busy just about to get in it will update you thanks again
Awesome video to brother 👍
Great video
Thanks!
Where can I buy a 35 percent gear reduction?
reduction boss
Is this the same install for a 2013 honda rancher 420? Or similar
yes I'm pretty sure its the exact same
@Dalton Bailey reduction boss, don oglesby
Isn’t that timing chain pretty stretched out?I can’t really tell
Nope, its a new wiseco chain
No, the guides make it look like it’s sagging but it’s tight.
Awesome video!
Thanks!
How much would it cost for you to do mine
Unfortunately we aren't doing any installs at the moment
Might be a over asked question but, what tire size is the starting point for needing a gear reduction. I have a 2017 foreman 500 FS
I’m in need of one and I’m on 28 in Moto havocs
@@TrentonHuggins my stock 500 is turning 29.5 outlaw 3s with relative ease but I still want to look into a gr
@@TrentonHuggins I pulled 28 havoks before on my 420 and it pulls them just fine without gear reduction
Does that 520 on assanators have a gr
Yes, 53%
@@vesselpowersports Ive got a 520 Rubicon and want to run 29.5" Assanators without a gear reduction... do you think it'll get bogged down or can it spin them pretty good
It will have np if you have a dct transmissin and you put it in low
Serious question, what way does the neutral switch face in the case, does the long or short side face neutral? Ple help
long side faces neutral!
With the 53 did you have to use washer behind GR
no, didn't use any shims for it
Same process for one with a dct?
if I'm not mistaken yes, just looks a little different
It’s not you have a gear in the back case
Where can i find a 35% reduction for my 14 rancher footshift 4x4?? I cant find any. Only ones i find is 07-13
22fabcreations.com
i need all the tools used in this video if u don't mind don't do great remembering lol.
10mm
27mm
6mm
12mm
14mm
hammer
extension
3 jaw puller or clutch puller tool
Should be everything lol
Um where can someone order that cargo door cup holder at 14 seconds. I've searched everywhere. Nothing. I'm starting to think it was 3D printed
its an oem honda part, check out tbm_customs on instagram and send them a message.
@@vesselpowersports lol literally minutes after I posted it this, we found it. It's 44.95ish on hondas website
Does this work for a DCT
Hey man u selling any hondas
Yes, soon
Let me know call me 352 727 3356
Thanks man
Where can I get a GR?
22fabcreations on instagram
If only you understood how much money and business you lost making this Video. SHMM 🤦🏻♂️
This is only up to 2021? I got a 22
works the same, just made the videos when the 21s first came out.