Organizing your RV storage with a MORryde sliding tray
ฝัง
- เผยแพร่เมื่อ 22 พ.ค. 2021
- This video will demonstrate how to install a Morryde sliding tray in your RV's outside storage compartment. We will show you how we organized our storage compartment on our Montana fifth wheel and the products we use to do so.
@morrydeinc
#keystonrvbrandambassador
#keystonemontana
#keystonrv
#jonesin2go
#morrydeslidingtray
#rvorganizing
#organizingyourrv
#RVstorage
#rvstorageorganizing
To see a complete line of MORryde products go to
www.morryde.com
to purchase the MoRyde pullout trya
www.etrailer.com/RV-Cargo-Sli...
Zero G 25' hose
www.amazon.com/Teknor-Apex-40...
Zero G 50. hose
www.amazon.com/Zero-G-Lightwe...
Music used in this video was provided by Epidemic Sound
Under my BBQ I use a piece of Cement board. It is heat resistant and you can wipe it clean.
Great video. I installed the same unit on our 2020 Keystone Cougar 315RLS. I also had to raise the frame about 1/2 an inch because like your's, when it was pulled out to the cross member it caught the bottom edge of the door frame. I used a strip of plywood on each side that runs the length of the slide frame and covered it in charcoal grey needle punched carpet to match the felt in the cargo bay Keystone put in there. Best accessory I did on the Cougar.
Very cool. I like the post with table and paper towel holder.
Thanks
Hoping to get one installed our Tandara soon. Thanks for sharing!
Great video, I just installed my cargo tray a few weeks ago. We are excited about our new 2021 Montana 3231CK - y’all have safe travels.
Thanks for watching. That's an awesome floorplan. Safe travels to you also.
Thank you ! Nice Video of what I want to achieve. Also how you tackled the little lift problem that I was worried about if I ordered wrong ! Thanks to your video I now know I don’t need there riser kit for our trailer. You may not be aware that a lot of us out there were unsure if we could buy a tray that swings both directions. I sent a Q ? Out to Amazon and finally got an answer. But once again your nice video confirms it. Super Cool
Thanks again for your time.
Also like your thinking on those pads
Good stuff
Thanks Chuck. I'm glad the information was helpful to you!
Hey Chuck just one thing I pretty sure I forgot to mention. Keep in mind that your black and gray holding tanks are under your front pass through so be mindful when choosing your screw length
Thanks for sharing
Thanks you for watching
Great video, looking forward to installing ours today into our 3120rl so finding your video is very timely.
One question, what size/length screws did you use? Thanks for sharing
I think they were 3 inch screws
Great video, thank you. Could show how you mounted hose and cord reel? My Grand design came with a hose reel, but am think of relocating it to a tray similar to your install? Are your reels power? If so how did you handle the slacking the wire? Thanks in advance!
Our reels are both manual and they are both just screwed the the tray. They are both moryde reels
Now that you’ve had this setup a while, do you still like having the blackstone on the tray? I just ordered a Moryde tray for our toy hauler and already had the same idea to put the Blackstone on the tray. Great video!
Yes I really like the blackstone on the tray. It's a great way to get it out and put it away fast and easy. Adding the tray was one of my favorite additions. Well worth it.
Awesome video, I’m wanting to pull the trigger on that purchase also. My only concern is, would there be a possibility of drilling into one of the tanks?
The outside screws would be outside the frame so the only location to be concerned about would be in the middle. That's where I used shorter screws.
I'm wondering if you have a link or remember the exact name of the Fast Rack post that you have next to the Blackstone?
Sure this is the tray I purchased at menards
www.menards.com/main/storage-organization/garage-outdoor-storage/wall-storage/rubbermaid-reg-fasttrack-reg-rail-trade-15-3-8w-x-9-1-2d-wall-mount-storage-shelf/1938439/p-1469035905698-c-12657.htm?tid=8616461644710850477&ipos=53. The bar that it mounts to should be located in the same display.
Nice vid. Thinking of getting one too.
Question: why does your cargo bay door have gas struts brackets on the inside of the door? They are completely useless due to the door swings all the way up.
Montana puts them on incase the customer wants to add the struts. I prefer it open all the way.
@@Jonesin2Go makes since.
Curious how hard it is to get behind the wall if you have a leak in the wetbay or one of your tanks?
Just a few screws and the panels pop right out.
Great video. Is that a 36 inch wide?
Yes it is 36" wide
I have a question I ordered mine from Amazon and came in damage today did your MORryde Sliding Cargo Tray come in a box. because mine didn’t
Mine was shipped in a box strapped to a pallet.
@@Jonesin2Go ok thanks
What’s the one inch spacer what’s the length of the screws you use
The 1" spacer is to elevate the drawer so that it clears the door frame. It is 1" squar aluminum tube. I used 2" screws on the ends (outside the frame) and shorter screws on the middle screws. Keep in mind your black and gray tanks are under that floor so measure for those screws carefully so they don't penitrate the flooring to far.
@@Jonesin2Go That’s why I was wonder about the tanks with the screws without hitting the tanks thanks just got 2022 Montana 3231 CK
@@brianchambers9842 congrats on the new rig. That's a great floor plan