i just got my storm32 and mounted it on my asp gimbal after having a few problems with the firmware and replacing the controller onto the top it works great, much betrer than the original alexmos 8bit i used before! great project, keep ip the great work
That's really cool. Great that it's based on the STM32 instead of the AVR328. Your brushless Gimbal direct drive theory blog post was really great as well.
quick question. i get this " Get Status... Please wait! v... Read... ABORTED!" does that mean the uploaded firmware is not the right version for the BGCTool?
+kpopRC When you flash the firmware you have to connect the USB-TTL wires to the RC port, then when you want to start "reading" and communicating normally with the board you have to connect the USB-TTL wires to the UART port.
When I put my gimbal on, the battery turns on but it can't calibrate .. after I connect the USB to the computer, it says the battery is not connected .. what should I do
pl go to the respective thread on rcgroups ... yt is not a good place to discuss such things. Also, pl provide more info, with the given info it's really impossible to give any advice. Also pl make sure you've double checked the obvious issues mentioned in the wiki.
Looking at commercial handheld gimbals like the Feiyu G3, they can support flipping the pan and roll motors when the hand stick is pointing forward rather than up. Can STorM32 support this trick?
Bonjour, je me permets de mettre un commentaire. Je possède la carte v1.32 storm 32. Le problème que je rencontre et que je n'arrive pas à flasher la carte. Pourriez-vous m'aider s'il vous plaît. Cordialement.
hello, does this stabilizer work with apm 2.8? when connecting power to the gimbal, this autocalibra well, but I have not yet managed to make the pitch movement with a wheel of the flysky-i6s, I have connected the signal cable directly to the receiver , I have assigned an auxiliary channel, channel 6, and nothing at the moment. Can you help me solve it?
hello problème : v2.11e nt read aborted the connected controller board or its firmware version is not supported retry with GUI version v2.11e nt i don't found this version ? actually : storm32 v1.3x firmware v2.30NT thanks
I bought the same board as you minus Bluetooth..I plugged to my gimbal nothing is happening..any advise just a flashing red light solid green light. Plus I'm gonna hook up control stick also I don't know the wire diagram
beautiful work OlliW! I have the BGC v0.90 that came with my cheap gimbal. Doing some final calibrations to get it flying. I do have a FTDI to do the firmware upgrades but I'm a simple quadcopter pilot and am not sure I will benefit from the firmware upgrades and I definitely don't want to brick it. I'll probably only use pitch adjustment while flying in hold hold pan mode. Should I upgrade? Or should I use it as is and see? Thanks!
I make a gimbal as a thesis for school based on storm32. Everything is assembled, I went through the configuration, but the axes start to vibrate and do not stabilize. Could anyone help? Thanks in advance!
Hello First of all, thank you for developing such a great product and sharing it from an open source. I was looking at the schematic of the versions of Storm32. I want to make some minor changes. I could not find the schematic of the STorM32 v1.32 model. I wonder if you didn't share it or not. Thank you. Best regards
@@OlliW42 I wrote that it is on the website www.olliw.eu/storm32bgc-wiki/STorM32_Boards. So where can I find the design schematic? There is also another question I would like to ask. Which driving method did you use as an engine control? FOC, Trapezoidal etc .. I have to write a thesis on a card like Storm32. This will be my undergraduate thesis. I can find many necessary documents on the pages. I need a little more detail frankly. I'm trying to make benchmarks right now
hello I have same board and all. ready calibrate, after power up I have beep and gimbal ready. but not work properly, I think same parameter it is not ok, but I don't know what parameter change. Can you help me and send me screenshot with correct parameter pid and more?
this is really not under my control since I don't sell them, i.e., it totally and only depends on the vendor. The offers I'm aware of however have at least one IMU module for the camera included.
Hi man, check the play store. It's called Simplebgc. I saw another video about it, but I haven't tried it. If you do try it, and it works.. Please feel free to comment and tell me =D
i just got my storm32 and mounted it on my asp gimbal
after having a few problems with the firmware and replacing the controller onto the top it works great, much betrer than the original alexmos 8bit i used before!
great project, keep ip the great work
That's really cool. Great that it's based on the STM32 instead of the AVR328. Your brushless Gimbal direct drive theory blog post was really great as well.
Gefällt mir, freue mich schon auf das Board... Sehr gute Arbeit.
quick question. i get this "
Get Status... Please wait!
v...
Read... ABORTED!"
does that mean the uploaded firmware is not the right version for the BGCTool?
I was getting the same error and then discovered the board needed to be flashed.
+kpopRC When you flash the firmware you have to connect the USB-TTL wires to the RC port, then when you want to start "reading" and communicating normally with the board you have to connect the USB-TTL wires to the UART port.
kpopRC လိးးက ညလူးကာ
Hello, you kindly spend your file parameters of the gimbal 32 storm? I do not get well calibrated
When I put my gimbal on, the battery turns on but it can't calibrate .. after I connect the USB to the computer, it says the battery is not connected .. what should I do
pl go to the respective thread on rcgroups ... yt is not a good place to discuss such things. Also, pl provide more info, with the given info it's really impossible to give any advice. Also pl make sure you've double checked the obvious issues mentioned in the wiki.
Looking at commercial handheld gimbals like the Feiyu G3, they can support flipping the pan and roll motors when the hand stick is pointing forward rather than up. Can STorM32 support this trick?
Bonjour, je me permets de mettre un commentaire. Je possède la carte v1.32 storm 32. Le problème que je rencontre et que je n'arrive pas à flasher la carte. Pourriez-vous m'aider s'il vous plaît. Cordialement.
hello, does this stabilizer work with apm 2.8?
when connecting power to the gimbal, this autocalibra well, but I have not yet managed to make the pitch movement with a wheel of the flysky-i6s, I have connected the signal cable directly to the receiver , I have assigned an auxiliary channel, channel 6, and nothing at the moment. Can you help me solve it?
hello problème : v2.11e nt
read aborted
the connected controller board or its firmware version is not supported
retry with GUI version v2.11e nt
i don't found this version ?
actually : storm32 v1.3x firmware v2.30NT
thanks
where you get the GUI can't find it anywhere
Olli can you help me I can't get my gearbest hakrc 3 axis gimbal to work. It will not power up the main board but the imu light comes on?
my GUI show my IMU is None ...2nd IMU is found
do I have defective board ?
Is it possible use the BGC Gimbal Board with a regular servo instead Brushless Motor?
I bought the same board as you minus Bluetooth..I plugged to my gimbal nothing is happening..any advise just a flashing red light solid green light. Plus I'm gonna hook up control stick also I don't know the wire diagram
is this board made for smaller cameras or it doesn't mattet
Ty.hd life films
beautiful work OlliW! I have the BGC v0.90 that came with my cheap gimbal. Doing some final calibrations to get it flying. I do have a FTDI to do the firmware upgrades but I'm a simple quadcopter pilot and am not sure I will benefit from the firmware upgrades and I definitely don't want to brick it. I'll probably only use pitch adjustment while flying in hold hold pan mode. Should I upgrade? Or should I use it as is and see? Thanks!
please specify the specifications of the motor used.
Can this servos stabilizer be controlled by a flight controller?
I make a gimbal as a thesis for school based on storm32. Everything is assembled, I went through the configuration, but the axes start to vibrate and do not stabilize. Could anyone help? Thanks in advance!
Can i use this controller for a DSLR-size gimbal? Thanks for making 3-axis-controllers affordable
gagomand Bump.
Update on my side too, I made it work with a gimbal for DSLR's.
Does it work well?
Hello First of all, thank you for developing such a great product and sharing it from an open source. I was looking at the schematic of the versions of Storm32. I want to make some minor changes. I could not find the schematic of the STorM32 v1.32 model. I wonder if you didn't share it or not. Thank you. Best regards
v1.32 is not my design (it is based on my design but modified)
@@OlliW42 I wrote that it is on the website www.olliw.eu/storm32bgc-wiki/STorM32_Boards. So where can I find the design schematic? There is also another question I would like to ask. Which driving method did you use as an engine control? FOC, Trapezoidal etc .. I have to write a thesis on a card like Storm32. This will be my undergraduate thesis. I can find many necessary documents on the pages. I need a little more detail frankly. I'm trying to make benchmarks right now
hello I have same board and all. ready calibrate, after power up I have beep and gimbal ready. but not work properly, I think same parameter it is not ok, but I don't know what parameter change. Can you help me and send me screenshot with correct parameter pid and more?
Hi its not responding to my imu Its as if its not detected It is plugged in
Very good job. May you put where buy all component´s. Thank´s
congratulations! Excellent work!!!
Can anyone please tell me where I can find the Windows 8 driver for StorM32 1.31 controller? Thanks.
Do I have to buy the Sensors? Or are they included if I want to buy this board? Very Cool Video
this is really not under my control since I don't sell them, i.e., it totally and only depends on the vendor. The offers I'm aware of however have at least one IMU module for the camera included.
Has anyone made a Bluetooth GUI app for the android if so can you please point me in the right direction to find it
Hi man, check the play store. It's called Simplebgc. I saw another video about it, but I haven't tried it.
If you do try it, and it works.. Please feel free to comment and tell me =D
u did a gr8 job and you deserve a big Like
very good,i like storm32 bgc
good presentation ! goodluck
Very nice job. :-)
NICE!
tnx
Nice!!
..thumbs down by Alex Moskalenko? ;)
Great work, thanks Olliw!
Fyi active topic for storm32 : www.rcgroups.com/forums/showthread.php?t=2055844