Dear OlliW, thanks for sharing all your insights about gimbals. May I ask you for a quick favor: Could you point out just one BLDC gimbal motor for the roll axis and use with a gopro camera? Ideally, it would just have three stranded cables (no fancy ribbon cable). I am aware there are many hints on your webpage about choosing gimbal motors, but I was unable to find an answer pointing to an actual current product. Thanks again! Martin
hey Martin that's a difficult question since the market on gimbal motors is extremely thin, and it also changes very quickly. Some time ago I got me HT2205, and these are not so bad (see www.rcgroups.com/forums/showthread.php?2838548-T-STorM32-The-best-STorM32-ever-%21/page34&perpage=50#post44755287) but I frankly have no idea if they are still available (if so, only from aliexpress, I would guess) cheers, Olli
Dear OlliW, I have a problem with flashing firmware into the STorM32 BGC V1.32 (DRV8313), it said "No response from the target, the Bootloader cannot be started." I'm using FTDI FT232RL as the USB-TTL, and I'm sure there's no mistake on the wiring. I've searched for some similar issues in the Storm32-bgc Wiki, but I couldn't find the most recent threads that's using the same board version as mine. I would be so thankful if you're willing to help me solving this issue. Thanks!!
well, unless your board is bricked, for which there is no reason to believe this at this point in time, somewhere something must be wrong. It's hard to say aynthing more with the current info at hand. You are sure you follow the wiki? The error message is unknown to me. Maybe you could consider joining the rcgroups discussion thread. Btw, the board version does not matter, all v1.3x type boards are equal as regards flashing. So, the description in the wiki does apply to your v1.32.
@@OlliW42 I literally just bought it, and it's working fine. I just want to tune the PID. I've checked the board with multimeter, I could find that the board's connection looks like this: RC-0 (Uart1-RX) = connected to IC pin 58 (PB6) RC-1 (Uart1-TX) = connected to IC pin 59 (PB7) Is this true? because if it is, I think I've lost Uart1-RX connection between the PORT and the IC's pin. Thanks!!
pl, read the wiki. I cannot overemphasize this. You are not going to have any fun with STorM32 if you don't. Read the wiki, and strictly do what it says. The scheme for the v1.3 board is available, and the v1.32 is not different except in some irrelevant parts. The scheme can tell you all details you ever wanted to know. No, RC0/1 should go to UART1 PA9/10, and tehre is also a inverted.
OlliW is it possible to buy your tiny STM32 F7 Strom controller ( 0:50 sec in the video) now?
no. Since chip crisis isn't over for us there is no such board actually. Even if all this would not be there, a manufacturer would have to jump on it.
Dear OlliW,
thanks for sharing all your insights about gimbals.
May I ask you for a quick favor: Could you point out just one BLDC gimbal motor for the roll axis and use with a gopro camera? Ideally, it would just have three stranded cables (no fancy ribbon cable).
I am aware there are many hints on your webpage about choosing gimbal motors, but I was unable to find an answer pointing to an actual current product.
Thanks again!
Martin
hey Martin
that's a difficult question since the market on gimbal motors is extremely thin, and it also changes very quickly. Some time ago I got me HT2205, and these are not so bad (see www.rcgroups.com/forums/showthread.php?2838548-T-STorM32-The-best-STorM32-ever-%21/page34&perpage=50#post44755287) but I frankly have no idea if they are still available (if so, only from aliexpress, I would guess)
cheers, Olli
Dear OlliW, I have a problem with flashing firmware into the STorM32 BGC V1.32 (DRV8313), it said "No response from the target, the Bootloader cannot be started." I'm using FTDI FT232RL as the USB-TTL, and I'm sure there's no mistake on the wiring. I've searched for some similar issues in the Storm32-bgc Wiki, but I couldn't find the most recent threads that's using the same board version as mine. I would be so thankful if you're willing to help me solving this issue. Thanks!!
well, unless your board is bricked, for which there is no reason to believe this at this point in time, somewhere something must be wrong. It's hard to say aynthing more with the current info at hand. You are sure you follow the wiki? The error message is unknown to me. Maybe you could consider joining the rcgroups discussion thread. Btw, the board version does not matter, all v1.3x type boards are equal as regards flashing. So, the description in the wiki does apply to your v1.32.
@@OlliW42 I literally just bought it, and it's working fine. I just want to tune the PID. I've checked the board with multimeter, I could find that the board's connection looks like this:
RC-0 (Uart1-RX) = connected to IC pin 58 (PB6)
RC-1 (Uart1-TX) = connected to IC pin 59 (PB7)
Is this true? because if it is, I think I've lost Uart1-RX connection between the PORT and the IC's pin. Thanks!!
pl, read the wiki. I cannot overemphasize this. You are not going to have any fun with STorM32 if you don't. Read the wiki, and strictly do what it says. The scheme for the v1.3 board is available, and the v1.32 is not different except in some irrelevant parts. The scheme can tell you all details you ever wanted to know. No, RC0/1 should go to UART1 PA9/10, and tehre is also a inverted.
Thank You