This may be a silly question but does the odometer reading starts at 0 when you first install it or do you need to manually enter it? Also, does it reset if the battery dies?
Most people mount the Trail Tech Vapor in addition to the stock speedometer/gauge cluster but I have seen on forums where people do a little extra work and completely replace the stock gauges.
You will want to go through and check all the sensors and wiring. You can check out the link below to directions on the Vapor which should help you figure out where your problem is: www.rockymountainatvmc.com/docs/vapor_instructions.pdf
how do i reset it i have a 2020 yz450f that i had dirt tires on it with he speedometer and it worked great before i put on my super moto wheels. When i put them on my speed stoped showing the only thing showing was the rpm time and everything except the speed of the bike if you can please tell me thanks
Hello , I need some help , my milage on my older vapor somehow got screwed up last summer when my scooter was in storage for 6 months and is now stuck at 1999 miles . It was higher then that but went down and is now not going up . The magnet on the wheel is still there and the sensor is intact too . Any ideas about what happened or how to fix the issue would be much appreciated. My unit does not say vapor on it but looks identical otherwise so I am just assuming its a vapor please correct me if I am wrong . Thanks
What are the settings for a 21 inch enduro wheel,? Think the most guys use it on there enduro bikes so 21inch is the normal size. They had better notice it in the paperwork
@@masonroy2944 turns out you don't splice anything. I bought this product 3 months ago.. You wrap the wire around your spark plug wire between the two boots and it wirelessly/inductively reads the RPMs by pulses through the wire.
@@masonroy2944 if you go onto the trail tech website you can download their user manuals and in each there are installation instructions. Most all the trail tech gauges use this method.
Hold all three buttons for 3sec and the device will ender "Data Setting Mode". Press Mode to cycle through the devices settings until you get to clock. The device defaults to 12h format. Press Mode again and digits on the clock should begin to flash. At that point use the arrow buttons to change the time and press mode to confirm. After 15sec of no buttons pushed the device will return to home screen.
That is correct. There is an instruction manual for the Trail Tech Vapor you can check out here: www.rockymountainatvmc.com/docs/vapor_instructions.pdf
Here's a link to the instructions: www.rockymountainatvmc.com/docs/vapor_instructions.pdf Page 16 is where the instructions are for configuring the settings.
I know this is an old video but I am just now figuring out about these. On the official trail tech website it says the vapor will fit on my 2005 yamaha bruin 350 but on Rocky Mountain website it says it will not can someone help?
Yes, these are bike specific and will work for your 2018 FE501. You can check it out here, just enter your bike and you'll be good to go: www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p Thanks for watching!
Yes, it does work, however, this is already a great digital speedo available that is plug and play for the Hawk 250. Look on the Chinarider forum or hawk250 dot com
not sure about hours, but this is to add mileage. :Press and hold all three buttons down for three seconds to enter the data setting mode. Once there using the mode button progress to the tire size. At the tire size enter 9110 using the left and right had buttons to increment the digits. Immediately after entering the new tire size press and hold the right hand button down for three second. This should move to a screen with ( 12HR ) flashing on it. If this is displayed you are in the permanent data set so any alterations will be saved to the permanent information. Once in this data set again using the mode button move to desired screen in this case the screen that reads ODO for odometer. Finally using the left and right buttons again alter the ODO to desired mileage. Once complete you can either wait for five seconds and let the Vapor revert back to the main screen or you can use the mode button to reach the main screen. Resetting the proper tire size is not needed since the Vapor with automatically default back to the values you had set prior to this adjustment.
Below is a link to the Trail Tech Vapor Instructions, where instructions on how to switch between M/H and KM/H can be found on page 16. www.rockymountainatvmc.com/docs/vapor_instructions.pdf
@@rmatvmc Thank you thank you I appreciate it I will comment back on here once I figure it out and get it back to miles per hour I appreciate your help good business right there
Trail Tech doesn't list any kits working for the Bruin but they do have some for other ATV's so you may be able to contact them directly and see if you would be able to make one work for your quad.
Yes, these will work for a Banshee 350. Just make sure to select your correct machine when looking at the part. You can check it out here: www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p Thanks for watching!
I asked the company a while back regarding a possible installation for an MZ sx125, their verdict was it should be possible, but probably best to contact them and get the right version number, which I don't have to hand. There is a 'generic' version for a single cylinder four stroke, you may need to go the route of a temperature sensor that attaches to the radiator rather than the one that goes inline with the coolant flow, from memory the issue was the pipe/hose diameters being mismatched. Probably the greater issue will be getting the right sensors, the head itself should then work fine, I still plan to use one but haven't got to that stage in the build yet. Best of luck.
Yes, we do have this available for your machine. Check the link below for more information: www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p
Yes, these will work for the KFX! Just make sure you enter your quad on the product page. www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p
@@radiouniquefm Just enter your machine on the product page and you'll be set! www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p
The link below will take you to the instruction manual for the Trail Tech Vapor. Directions for kph to mph conversion should be located on pages 16 and 17. www.rockymountainatvmc.com/docs/vapor_instructions.pdf
I really want to get one and it would be nice to get a aluminum cage for it but $160 for everything.. it’s too expensive for me I’m only 16 I would love to get into racing
We don't have the Vapor available for your ATV, but we do have 3 other Trail Tech computers that will work for your machine. You can check those out here: www.rockymountainatvmc.com/parts/atv-electrical?v=2017-yamaha-kodiak-700-4x4
Can you use the top indicators for turn signal indicators?
Might sound stupid, but can you replace the battery in it after it dies?
yes it takes a CR2032 battery
Well that battery is only used for the clock so it keeps time while the bike isn’t running. You prolly won’t need to worry about that
This may be a silly question but does the odometer reading starts at 0 when you first install it or do you need to manually enter it? Also, does it reset if the battery dies?
Great question - also waiting for an answer.
What does it mean if the right/red LED is steady on after I turn the bike off?
will this work on a 2017 kodiak 700 base model that came with no speedometer? too poor to spend on an esp. jw
Rocky, kindly facilitate I get a used one and have it sent to Kenya for my Serow. Kindly advice
I love mine.. water temp, air temp, speedo. I have one setup on my 1988 TRX 250r .
Looks good qq if I'm buying a honda xr650l duel sport would it replace the speedometer or would it be put on as a secondary???
Most people mount the Trail Tech Vapor in addition to the stock speedometer/gauge cluster but I have seen on forums where people do a little extra work and completely replace the stock gauges.
i just got a Honda CRF 250L what has this on it but the rev and speedo is not working can you help
You will want to go through and check all the sensors and wiring. You can check out the link below to directions on the Vapor which should help you figure out where your problem is:
www.rockymountainatvmc.com/docs/vapor_instructions.pdf
Will it work for a Honda recon
Does it still fit if you have protaper bars on and your key in normal spot
Yes
how do i reset it i have a 2020 yz450f that i had dirt tires on it with he speedometer and it worked great before i put on my super moto wheels. When i put them on my speed stoped showing the only thing showing was the rpm time and everything except the speed of the bike if you can please tell me thanks
There is a small reset button on the backside of the display. It will erase all data including clock and trip distance.
Will this work on a mini bike or better yet generator style motor that doesn't have a full-on wiring harness
Can one gets suitable one for my Yamaha serow Xt 225 plus the protective casing, and for how much if am to ship to Kenya? Advice
Hello ,
I need some help , my milage on my older vapor somehow got screwed up last summer when my scooter was in storage for 6 months and is now stuck at 1999 miles . It was higher then that but went down and is now not going up . The magnet on the wheel is still there and the sensor is intact too . Any ideas about what happened or how to fix the issue would be much appreciated.
My unit does not say vapor on it but looks identical otherwise so I am just assuming its a vapor please correct me if I am wrong .
Thanks
Is there anything specifically for a Kayo T2 yet? Or anything universal?
What are the settings for a 21 inch enduro wheel,? Think the most guys use it on there enduro bikes so 21inch is the normal size. They had better notice it in the paperwork
How about for a 89 TW00, will this work?
Thanks!
nice I was wondering I have an 1984 xv1000 yamaha can i use this on it I'm doing a bobber build looks nice
How does it get it's rpm signal and can it be driven by an inductive sensor for rpm
I’m pretty sure you splice a wire leading to your spark plug and that’s how it gets the rpm
@@masonroy2944 turns out you don't splice anything. I bought this product 3 months ago.. You wrap the wire around your spark plug wire between the two boots and it wirelessly/inductively reads the RPMs by pulses through the wire.
@@masonroy2944 if you go onto the trail tech website you can download their user manuals and in each there are installation instructions. Most all the trail tech gauges use this method.
dose it fits in a Yamaha Raptor 700r 2020 ?
How do you set the correct time
Hold all three buttons for 3sec and the device will ender "Data Setting Mode". Press Mode to cycle through the devices settings until you get to clock. The device defaults to 12h format. Press Mode again and digits on the clock should begin to flash. At that point use the arrow buttons to change the time and press mode to confirm. After 15sec of no buttons pushed the device will return to home screen.
does it work for Aprilia mx125? all Features?
Will This Work On My Shifter Kart? The Engine Is a 140cc Pit Bike Engine
Can you fit to a 2018 suzuki-ozark-250?
Will the tac work on a bike that comes with no gauges
Yes, that is the whole idea.
So, it has its own battery source or does it have to be wired?
It has its own coin battery.
Does it get wired to the bike’s battery
That is correct. There is an instruction manual for the Trail Tech Vapor you can check out here: www.rockymountainatvmc.com/docs/vapor_instructions.pdf
How do you set up the time?
Here's a link to the instructions: www.rockymountainatvmc.com/docs/vapor_instructions.pdf
Page 16 is where the instructions are for configuring the settings.
Can this be hooked up to 2006 CR85
I know this is an old video but I am just now figuring out about these. On the official trail tech website it says the vapor will fit on my 2005 yamaha bruin 350 but on Rocky Mountain website it says it will not can someone help?
I really wanna put it on my '09 Ninja 500R. Would it fit?
How do you turn off this gauge after the bike is off with it connected to electric start?
The gauge will turn off automatically after 20mins of the bike not moving.
Awesome product
3:11 if I change my current clock will my ART change
Will this work on a 1983 atc250r
what about a plastic cover for the metal shell and/or mounts for gy6 scooters
Can you have the light on the screen stay on for night/ evening riding ?
Yes you can keep the back light on while riding at night.
I realize it is not resetable but can I set the art and odometer to my current readings upon initial setup??
Yes
Will that work on 2007 Kawasaki Ninja 250R?🥺
Will it work on a 2007 raptor 700r se ... if so is there a mounting bracket for it and my quad
Yes this will work on your Raptor and the mounting hardware will be included!
@@rmatvmc ok thank you
Will this work for a 2019 Kawasaki klx140g? Because it asks for my bike but i dont see the 140g.
It’s a universal kit. You can make it fit your bike. The installation is the same for any bike you put it on
Will it work on Yamaha tw200 2019 -2018?
Show my video TUTO : th-cam.com/video/ZuaboHMFjWw/w-d-xo.html
Is there a light or a signal that tells you when your on nutreual
The Trail Tech Vapor does not have a neutral indicator light.
Any other recommendations of speedometers with neutral indicator light im a beginner rider
What is the battery life like ? Is it replaceable or will I need to buy a new one ?
These are designed to plug into a bike's wiring harness and use the bike's power source. You will not need to replace the battery.
@@rmatvmccan put this in a banshee without batterie?
Does it show what gear you are in ?
No, unfortunately this unit does not have a gear indicator.
Im interested but how to purchase? How much?
Are you able to adjust wheels size?
Yes, you can definitely adjust the wheel/tire size to your needs.
how does it look at night?
And will it work on a qlink xf200 enduro?
Is it universal for dirt bikes?
Will it work for husqvarna FE501 2018
Yes, these are bike specific and will work for your 2018 FE501. You can check it out here, just enter your bike and you'll be good to go: www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p
Thanks for watching!
Show my video TUTO : th-cam.com/video/ZuaboHMFjWw/w-d-xo.html
What makes it vehicle specific? Why can't is be universal to use on any bike?
There are a few different mounts and some bike-specific sensors. With that said, these units can still be used on a wide range of machines.
Can you get this to fit a Chinese Hawk 250 dirt bike?.
I'm not familiar with that bike so i can't give a great answer. But if your bike has wiring harness/system then you should be ok.
Yes, it does work, however, this is already a great digital speedo available that is plug and play for the Hawk 250. Look on the Chinarider forum or hawk250 dot com
what if i already have hours on the bike..say 50 can i start the hour meter there? 2018 crf250r
Unfortunately, I don't think that is an option for these. But if you know how many hours you already have on it you can always just add that on.
not sure about hours, but this is to add mileage. :Press and hold all three buttons down for three seconds to enter the data setting mode. Once there using the mode button progress to the tire size. At the tire size enter 9110 using the left and right had buttons to increment the digits. Immediately after entering the new tire size press and hold the right hand button down for three second. This should move to a screen with ( 12HR ) flashing on it. If this is displayed you are in the permanent data set so any alterations will be saved to the permanent information. Once in this data set again using the mode button move to desired screen in this case the screen that reads ODO for odometer. Finally using the left and right buttons again alter the ODO to desired mileage. Once complete you can either wait for five seconds and let the Vapor revert back to the main screen or you can use the mode button to reach the main screen. Resetting the proper tire size is not needed since the Vapor with automatically default back to the values you had set prior to this adjustment.
I can’t figure out how to switch it back to mph ?? Some how it changed to kph
Below is a link to the Trail Tech Vapor Instructions, where instructions on how to switch between M/H and KM/H can be found on page 16.
www.rockymountainatvmc.com/docs/vapor_instructions.pdf
@@rmatvmc Thank you thank you I appreciate it I will comment back on here once I figure it out and get it back to miles per hour I appreciate your help good business right there
I would like to know the price of that complete kit
Daniel Kiogora it like 150
Would it work on a 2018 raptor 700r se
Yes
will this work with a yamaha bruin 250 ?
Trail Tech doesn't list any kits working for the Bruin but they do have some for other ATV's so you may be able to contact them directly and see if you would be able to make one work for your quad.
Will it work for banshee
Yes, these will work for a Banshee 350. Just make sure to select your correct machine when looking at the part. You can check it out here: www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p
Thanks for watching!
Is it waterproof?
This computer is not waterproof but will hold up just fine to rain, mud and washing your machine.
Will work for banshee 350
Thanks for the confirmation.
Yamaha banshee??
Can this work on a 03 yamaha blaster
Yes you just have to google search for it. I have one on my blaster
Will it work at an mz Sm 125 2004?
I asked the company a while back regarding a possible installation for an MZ sx125, their verdict was it should be possible, but probably best to contact them and get the right version number, which I don't have to hand. There is a 'generic' version for a single cylinder four stroke, you may need to go the route of a temperature sensor that attaches to the radiator rather than the one that goes inline with the coolant flow, from memory the issue was the pipe/hose diameters being mismatched. Probably the greater issue will be getting the right sensors, the head itself should then work fine, I still plan to use one but haven't got to that stage in the build yet. Best of luck.
Will this work with Kawasaki Bayou 250?
Unfortunately, this is not made for the Bayou 250. Sorry about that!
@@rmatvmc will it work with a yamaha grizzly 660? And does this have a 4x4 indicator?
Work in a yfz 450 2005?
Yes, we do have this available for your machine. Check the link below for more information:
www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p
Does it work for kfx450r?
Yes, these will work for the KFX! Just make sure you enter your quad on the product page.
www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p
Awesome vid
Install video would be nice.
I'm looking for this item for my 2020 Raptor 700r se
This would be a perfect addition to that and congrats on the new quad!
@@rmatvmc thank you 😊 do you have a link I can purchase it please
@@radiouniquefm Just enter your machine on the product page and you'll be set!
www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p
This fit a yamaha Raptor 350 2006
How to change to mph
The link below will take you to the instruction manual for the Trail Tech Vapor. Directions for kph to mph conversion should be located on pages 16 and 17.
www.rockymountainatvmc.com/docs/vapor_instructions.pdf
I think the hour meter should be resettable because I always get a new hour meter everytime I do a complete rebuild on my bike
I have one on a 2019 Raptor 700 keeps killing my battery anybody have any suggestions
Kill switch
Can it get wet
Id rather have a resetable trip meter than a ride time clock
Anyone running this on a banshee?
I really want to get one and it would be nice to get a aluminum cage for it but $160 for everything.. it’s too expensive for me I’m only 16 I would love to get into racing
Recon 250
It's to small
Nah
You are too small.
will this work on yamaha TTR 250 open enduro ?
I don’t have a option for 2002 TTR250 so what do I do?
Does this works on an old polaris sportsman 700 twin 2002??
I'm sure it probably would
Will this work on my 2000 Honda xr 200r ?
We don't carry it for that bike but Trail Tech does offer one on their site. The part number you would need for your bike is 752-115.
Hope that helps!
@@rmatvmc thank you
Will it work for 04 crf450r
Yes this is available for your bike.
www.rockymountainatvmc.com/parts/trail-tech-vapor-speedometer-tachometer-p
Recon 250
Will this work on a 2017 base model kodiak 700
We don't have the Vapor available for your ATV, but we do have 3 other Trail Tech computers that will work for your machine. You can check those out here: www.rockymountainatvmc.com/parts/atv-electrical?v=2017-yamaha-kodiak-700-4x4
Recon 250