On lubrication, many years ago one Sunday afternoon, when the weather was too bad to go out in, I decided to strip down, clean and lubricate the rear suspension on my bike (Kawasaki GPZ600R), mostly just because I was bored. Took off the chain, caliper, wheel, swingarm, rising rate linkage, shock and all the bearings. Cleaned everything with WD40 & degreaser (there was around 12 years worth of baked on road grime) and re-greased everything. Put it back together, and it transformed the bike. Ride and handling massively improved. Cost me 3 hours (ish), a couple of cans of WD and degreaser and a bit of grease. I wondered how often anyone does that to older bikes. Probably the most cost effective improvement you can do.
I am so lucky that I work at a machine shop/manufactory with a cleaning station, so I can take my bike inside and wash it and check all the above, as often that I want (mostly every second week) I always check tyre pressure and chain slack and lube it, I gave up looking at the oilglass as it do not use oil in between oil/filter changes and I do changes the brake/clutch fluid every 2-3 year and lube side stands aso a few times a year, and last time I change the spark plugs and filter I got a KN filter and iridium plugs so I don`t have to maintain them as much, only thing you did mention I kind a skib (beside the blinker fluid) is the throttle cables, never had a problem with them.
The rear wheel valve stem on the Iron 883 and Softail Standard pointing toward the center of the wheel is the biggest pain in ass to check. Pisses me off every time trying to get my tire pressure gauge either around the belt wheel or brake rotor. If the stem is not positioned exactly right it’s hard to check and I always scrape my knuckles.
I have never had a bike with angled stems. Straight stems are a pain. I bought a right angle air chuck from NAPA and a Accucheck tight angle tire gauge.
@@Sirloincloth1st I grease the splines whenever I have the rear wheel off. About every 15,000 miles to change the tire. My Wing has 100,000 miles on it and splines are fine
I got this nifty tire pump off Amazon. Battery powered. It tells me the tire pressure, and I can release or add pressure as needed. I usually check my tires every couple weeks, if things feel different, or heavy temperature changes.
I guess it depends on location, in Virginia and Florida where I live, I had/have no issues finding the free ones, but in Iowa, I know I used one that needed 50c to operate at a gas station or I'd just swing by my job if need be.
If you’re riding a Harley-Davidson and don't check your tire pressures because there is no “free air” I say owning one probably is not in your best interest. An air pump for the house is less than $30, you spent $$ thousands on the motorcycle.🤔
Definitely depends on where you are. I drove through Kansas and they had air at every gas pump that I stopped at didn't even have to go to a separate area it was right at the pump
Good talk! Thanx! Now that you mention it, its time to change the blinker fluid on my bike . I think , even though I dont make a lot of turns! I will make up a batch of my own recipe of blinker fluid because it does deteriorate as you know.! and its lot cheaper. ps check your ground connections on the older bikes like my 91 vx800 ! and battery terminals! cheers 84 yrs and still leanin!
Oooo that's a good one!! Keeping ground connections clean and making sure they are secure is very essential. I probably should start making my blinker fluid at home too but I'd probably still never use it😅 Thanks for commenting man! Stay safe 😁😁
I check the tires every ride! About 10yrs ago, the front tire lost some pressure on my XL1200. On flat road, I let her rip. When I crossed 70mph a sudden very violent tank slapper occurred! I coasted, trail braked and pushed against my handlebars and hung on! That was very scary. The tire lost 10LBS @23psi. The front tire on my 02' Deuce loses 5lbs in a week. The tubeless back tire always has the same until temperatures become colder.
dewalt air compressor cost me 150$ and is one of my most used "power tools", everyone if u can afford should get one! all be it if u already have tools its cheap to just buy one but if u have to buy a battery too it can get abit more pricey.
For tires, I prefer a regular bicycle pump over a compressor. Out garage compressor takes a while before it’s ready and then you have to stretch the hose out and coil it back. The bike pump is less work. Mine has a gauge built in. Once a week I attach the bike pump to each tire and give it a couple pumps if needed to keep the pressure on the money. It’s easy.
New subscriber. My 2022 XL883N Iron 883 which has very, very low mileage on it, I noticed on the throttle that there is too much slack and I heard the ideal free play is 2-3 mm, so I measured mine and it is 10 mm, 7 mm too much. It seems that my bike needs to be adjusted at the throttle because I am sure that my bike has never been adjusted before at the dealership where I purchased my Harley. When I do my upshifting to higher gears, I notice that there is a lagging response in acceleration (power) and smoothness. I also noticed that when I pulled the air filter off to inspect it for dirt and yes it was filthy, I inspected the butterfly valve and when I opened the throttle all the way, the butterfly valve was not opening all the way to flat position but was angled so I think I am losing power there as well. Probably will need to have idler cable adjusted as well.
If you own a 2017 Ktm 690 enduro r then checking oil level and tire pressure should become part of your before ride checklist lol. I really like my bike but it’s always “used” oil and gets unstable at speeds north of 80 mph if the tire pressure gets low. Once it hit 5500 miles the oil usage did lessen for some reason but by then checking its level had become a habit. It has been a very reliable bike and fun both on and off-road for me.
Thank you for those tips. I am a stickler for proper tire pressure before riding and was wondering if 38 lbs instead of 36 in the front would cause more wear. Can I use that lube you are using for everything you mentioned? I did not know that. I love the pop ups! 😄
you're welcome :) 2 psi in difference is very slightly and won't likely cause dramatic or noticeable uneven wear patterns. with more air than needed in tires, there is the decreasing grip but with 2psi difference, this difference will be minimal. That lube in the video I use strictly for cables but for general use, like hinges I use what I have available for the most part, I don't have a go to but ideally one that doesn't evaporate fast. wd-40 evaporate really fast. but for pivot points like on levers or kick stand or shifter shaft, I use a grease, also waterproof. Most brands are fine, I don't have go to for those things just because if you do it every time you do a routine service (5k miles), even a lower cost one will do just fine. I'm so happy to hear you're enjoying the videos :)
A few other things to check, lube, and adjust... Clutch cable, throttle cables, and most importantly primary chain adjustment and lubrication... Forgot to mention, steering neck bearing preload, lube, n swing away, n also front fork fluid changes. Rear fork, swing arm, also needs to be checked on occasion, for alignment n bearing preload...
Primary should be done at every oil change, the 3 hole service. But yeah I mentioned lubing clutch and throttle cables. Clutch adjustment should be checked every service as well, ideally.
Hey a lot of this stuff isn't what is mentioned in other videos. Your presentation is good and its cool to get the perspective and advice from an actual dealer mechanic
Good job here, except that you are talking about HD's ........I hate HD's!!!! All her tips are perfect, would only add spark plugs they are cheap unless you buy Iridium love her video!!!!!!
To be honest, i use what I have. Some are better than others just on regards of not coming off when water (rain) touches it. Some are water resistant. But when I use the ones that come off when water touches it, I just reapply sooner. I don't have a go to for general use. In the dealership there was a really good water resistant one but I can't remember the name of it
Come with me on a ride of pure imagination. I maintain my machines in turn key status and pre flight control systems and general condition points each ride. Happy Motoring!
Tyre pressure. OK here's what really annoys me about the dealer service department where I brough my bike from. the sticker on the swingarm states the recommended pressure for the factory tyres fitted to the bike, it has those very tyres fitted, yet when it was delivered to me the pressures were TOO HIGH and this made it slippery to the point of being dangerous. I reset the pressures and found that what was on the swingarm was pretty much exactly where they needed to be, so I had them EXACTLY where the needed to be for my weight and what I carry, which was what it said on the swingarm for the rear, and 1 psi less than the sticker for the front... And when I took it into the dealer for the first service they put the pressures at 10 psi above what they actually work well at. I'm so glad I felt it was wrong and stopped to fix it. because had I not done that I probably would have wiped out on the first ride! Dealers should LEAVE the customers tyres ALONE... the OWNER and Rider finds the best pressure for they tyres> not someone who has never ridden the bike! I will be specifically telling them NOT TO TOUCH MY TYRES OR THEY WILL BE REPLACING THE BIKE IF IT SLIPS OUT FROM BENEATH ME! I should also mention I am a Mechanic who has been racing cars for 30 years. I know what I am doing, and the only reason I take my bike to the dealer for services is so they can't get out of any warrantee claim! and then there's the oil change and how they did it, compared to how I told them to do it and referencing my qualification so they know they were dealing with a mechanic... did they spin the engine and trans up to free any sediment so it could drain out with the oil? No they did it cold when it had not been run in a while so all the fragments from machining and assembly could just sit in the engine and not be evacuated, so it can potentially damage the engine! this happens with many engines, and is why the first service is so soon after purchase!
It is cool to see a fellow Eastern European biker chick do a bike maintenance video. I am curious what is a good starter bike? Harley or an Indian. I would like to have a bike that I can take cross country as well as a canyon carver. Any advise would be appreciated.
can't go wrong with either, in the end it all falls down to your personal taste and preferences. You should test ride a few at both dealers to get a feel for which you prefer. :)
Starter bike that is a great canyon carver and good for cross country doesn't exist, no matter what reviewers or salespeople tell you. An Indian Scout can do all three, but the cross country part will be that which it does most poorly. It also has too much power and weight to be a good starter bike. Stay under 200 KG nd under 50 KW while learning to ride.
I ride a Harley Davidson! What is this horse power thingy ya speak of? 😅 And I keep my brake lines bleeding & my brakes greased! Also my blinker fluid is always topped off, it's easy to do without using them. (jk) On serious note, I'm amazed at how clapped the average used HD on market is. Lol I thought buying from a dealer would save me from that hassle, but it hasn't 😅
so I have yet to experiment with aftermarket brake pads but in the future, I know I would like to, just to personally know and feel the difference. I use stock but from others who ride, I have heard the some aftermarket brake pads are a lot better and worth it over stock oem ones. That's a great question though, sorry I couldn't give you a better answer but in the future, I might have something better to say regarding that. :)
@MotoDasha no worries, I have good luck with H.D. pads. However I've heard some AM pads are much better as far as stopping power,but they don't last long. Whether that's true or not, idk.
Very good md. I hit the subscribe button before I started typing. As a retired service manager and tech at a dealership the only thing I can add is the mission of hiring people with a functioning brain is almost futile. Any industry. I discovered that the bluer the arms, the least competent they tend to be. They have the wrong point of view, I think.
I don't know if this is helpful. I watched this video to see if you would demonstrate how to execute checking those important items you listed in your video. As fare would have it you didn't. Example: How you lube your throttle and brake cables, bleed your brake fluid. I'm just glad that you didn't mention checking the turn signal blinker fluid.
over heating from running rich due to a clogged air filter? it would actually run cool, but you will notice a loss in power and an increase in fuel consumption.
Great information, but please stop with the memes / gifs / unrelated popups because your audience are not kids, and even if your audience was mostly kids, this amount of cringe is hard to handle and it's not building you an audience, which is a shame because you give good information, always consider your audience if you are serious about being a professional youtuber.
If young people in the 60s, 70s did what you are doing, we would still be fighting the Vietnam war: avoiding sensitive national issues, avoiding following the money. On and on. We’ve got a major publicly traded company taking money from motorcycle buyers, from stockholders, and giving it to this this this… Forcing dei down on employees who have to choice. Are you ok giving your money to this this this? You have a say, you have a responsibility to step up. What do you stand for. No, instead, you are hiding behind a routine maintenance video. Please step up!
@@tranceminder2WTh is wrong with you? She’s doing this out of a passion and is obviously qualified. This video has nothing to do with your poor dei rhetoric.
the highest milage I have seen on a motorcycle was 150,000 miles approx. while I was a mechanic and it was in for a routine service. like cars, depends on how well you take care of the bike. And like cars, you can expect to do some repairs along the way to keep the life going. but typically, if taken care good, you can get 50,000 to 100,000 miles before you need to do any major work. Treat your bike poorly by not maintaining it right, ride is aggressively, not shift gears properly, you can expect issues much sooner.
![Motorcycle Dealership SERVICE DEPARTMENT Scams & Secrets [ Lies, Truth & Everything In Between ]](http://i.ytimg.com/vi/fwtWAT7SD-8/mqdefault.jpg)
On lubrication, many years ago one Sunday afternoon, when the weather was too bad to go out in, I decided to strip down, clean and lubricate the rear suspension on my bike (Kawasaki GPZ600R), mostly just because I was bored.
Took off the chain, caliper, wheel, swingarm, rising rate linkage, shock and all the bearings.
Cleaned everything with WD40 & degreaser (there was around 12 years worth of baked on road grime) and re-greased everything.
Put it back together, and it transformed the bike. Ride and handling massively improved.
Cost me 3 hours (ish), a couple of cans of WD and degreaser and a bit of grease.
I wondered how often anyone does that to older bikes. Probably the most cost effective improvement you can do.
Bach, Beethoven, Schubert, Chopin... You have great taste in music
Couldn`t you tell by her appearances ?
I am so lucky that I work at a machine shop/manufactory with a cleaning station, so I can take my bike inside and wash it and check all the above, as often that I want (mostly every second week) I always check tyre pressure and chain slack and lube it, I gave up looking at the oilglass as it do not use oil in between oil/filter changes and I do changes the brake/clutch fluid every 2-3 year and lube side stands aso a few times a year, and last time I change the spark plugs and filter I got a KN filter and iridium plugs so I don`t have to maintain them as much, only thing you did mention I kind a skib (beside the blinker fluid) is the throttle cables, never had a problem with them.
I was wondering what happens at the mechanic when the customers not around, TH-cam reading my mind again.Look forward to that video.
So do I
blinker fluid - classic :)
Thanks for some really practical advice on m/c maintenance, especially about checking my blinker fluid, luckily it was okay :)
I think mine leaked out. The ribbed tubes between the bike and the blinker housings cracked ...
she forgot the ashtray.
Just checked my blinkers and they were empty, so I filled them with water. Should be good now.
The rear wheel valve stem on the Iron 883 and Softail Standard pointing toward the center of the wheel is the biggest pain in ass to check. Pisses me off every time trying to get my tire pressure gauge either around the belt wheel or brake rotor. If the stem is not positioned exactly right it’s hard to check and I always scrape my knuckles.
I know exactly what you mean, it's annoying more than anything. 😅
I have never had a bike with angled stems. Straight stems are a pain. I bought a right angle air chuck from NAPA and a Accucheck tight angle tire gauge.
Road King Special points directly toward you. They are great for ease of checking tire pressures
@@jagjr6772 I have seen angled valve stems for wheels for tubeless tires. Sure helps a lot. My dual sport bikes have tubes.
LOL!! I know exactly what you mean by that.
You know those Harley mechanics aren’t checking anything that Harley advertises and charges you $800 for. Legal thieves
Good info. I'd add one too - Shaft drives are NOT maintenance free. Grease the splines every 20,000miles at least.
@@Sirloincloth1st I grease the splines whenever I have the rear wheel off. About every 15,000 miles to change the tire. My Wing has 100,000 miles on it and splines are fine
I got this nifty tire pump off Amazon. Battery powered. It tells me the tire pressure, and I can release or add pressure as needed. I usually check my tires every couple weeks, if things feel different, or heavy temperature changes.
There are very few gas stations that offer free air these days. Maybe the Harley Dealerships should offer free air.
I guess it depends on location, in Virginia and Florida where I live, I had/have no issues finding the free ones, but in Iowa, I know I used one that needed 50c to operate at a gas station or I'd just swing by my job if need be.
If you’re riding a Harley-Davidson and don't check your tire pressures because there is no “free air” I say owning one probably is not in your best interest. An air pump for the house is less than $30, you spent $$ thousands on the motorcycle.🤔
Definitely depends on where you are. I drove through Kansas and they had air at every gas pump that I stopped at didn't even have to go to a separate area it was right at the pump
I use a high pressure bicycle floor tire pump with a pressure gauge and it works great.
Naw, they just recommend new tires. The air in those old tires is old and deflated.
Good talk! Thanx! Now that you mention it, its time to change the blinker fluid on my bike . I think , even though I dont make a lot of turns! I will make up a batch of my own recipe of blinker fluid because it does deteriorate as you know.! and its lot cheaper. ps check your ground connections on the older bikes like my 91 vx800 ! and battery terminals! cheers 84 yrs and still leanin!
Oooo that's a good one!! Keeping ground connections clean and making sure they are secure is very essential.
I probably should start making my blinker fluid at home too but I'd probably still never use it😅
Thanks for commenting man! Stay safe 😁😁
I check the tires every ride! About 10yrs ago, the front tire lost some pressure on my XL1200. On flat road, I let her rip. When I crossed 70mph a sudden very violent tank slapper occurred! I coasted, trail braked and pushed against my handlebars and hung on! That was very scary. The tire lost 10LBS @23psi. The front tire on my 02' Deuce loses 5lbs in a week. The tubeless back tire always has the same until temperatures become colder.
Great video. I have been riding since 1969 and your reminders are priceless.
Check your fenders as well. I was thrown once when the damn fender came loose and locked up my front tire. Not a good time.
dewalt air compressor cost me 150$ and is one of my most used "power tools", everyone if u can afford should get one! all be it if u already have tools its cheap to just buy one but if u have to buy a battery too it can get abit more pricey.
For tires, I prefer a regular bicycle pump over a compressor. Out garage compressor takes a while before it’s ready and then you have to stretch the hose out and coil it back. The bike pump is less work. Mine has a gauge built in. Once a week I attach the bike pump to each tire and give it a couple pumps if needed to keep the pressure on the money. It’s easy.
Don’t forget the muffler bearing!
So Critical and soooo overlooked.... i lost my pappy to a bad muffler bearing.
New subscriber. My 2022 XL883N Iron 883 which has very, very low mileage on it, I noticed on the throttle that there is too much slack and I heard the ideal free play is 2-3 mm, so I measured mine and it is 10 mm, 7 mm too much. It seems that my bike needs to be adjusted at the throttle because I am sure that my bike has never been adjusted before at the dealership where I purchased my Harley. When I do my upshifting to higher gears, I notice that there is a lagging response in acceleration (power) and smoothness. I also noticed that when I pulled the air filter off to inspect it for dirt and yes it was filthy, I inspected the butterfly valve and when I opened the throttle all the way, the butterfly valve was not opening all the way to flat position but was angled so I think I am losing power there as well. Probably will need to have idler cable adjusted as well.
Good to hear a mechanics POV of maintenance on bikes! Subscribed, and looking forward to your videos.
If you own a 2017 Ktm 690 enduro r then checking oil level and tire pressure should become part of your before ride checklist lol. I really like my bike but it’s always “used” oil and gets unstable at speeds north of 80 mph if the tire pressure gets low. Once it hit 5500 miles the oil usage did lessen for some reason but by then checking its level had become a habit. It has been a very reliable bike and fun both on and off-road for me.
Thank you for those tips. I am a stickler for proper tire pressure before riding and was wondering if 38 lbs instead of 36 in the front would cause more wear. Can I use that lube you are using for everything you mentioned? I did not know that. I love the pop ups! 😄
you're welcome :) 2 psi in difference is very slightly and won't likely cause dramatic or noticeable uneven wear patterns. with more air than needed in tires, there is the decreasing grip but with 2psi difference, this difference will be minimal.
That lube in the video I use strictly for cables but for general use, like hinges I use what I have available for the most part, I don't have a go to but ideally one that doesn't evaporate fast. wd-40 evaporate really fast. but for pivot points like on levers or kick stand or shifter shaft, I use a grease, also waterproof. Most brands are fine, I don't have go to for those things just because if you do it every time you do a routine service (5k miles), even a lower cost one will do just fine.
I'm so happy to hear you're enjoying the videos :)
A few other things to check, lube, and adjust... Clutch cable, throttle cables,
and most importantly primary chain adjustment and lubrication... Forgot to mention, steering neck bearing preload, lube, n swing away, n also front fork fluid changes.
Rear fork, swing arm, also needs to be checked on occasion, for alignment n bearing preload...
Primary should be done at every oil change, the 3 hole service. But yeah I mentioned lubing clutch and throttle cables. Clutch adjustment should be checked every service as well, ideally.
Wonderful coverage. Loved the blinker fluid. Dah.
Dah is OK. I find the flash is brighter with BS.
Hey a lot of this stuff isn't what is mentioned in other videos. Your presentation is good and its cool to get the perspective and advice from an actual dealer mechanic
You're awesome, helpful and fun video thank you :)
Can you send link for that lube for cable and clutch lines ?
Bosch easy pump is a good answer for anyone looking for a cheap effective pump, that you can actually carry with you
I lube my muffler bearings regularly
Lots of important and useful info.
Another great vid Dasha; you have such a soothing voice.👍
Good job here, except that you are talking about HD's ........I hate HD's!!!! All her tips are perfect, would only add spark plugs they are cheap unless you buy Iridium love her video!!!!!!
Hey Dasha just found your vid and you're really cool . Thanks for the great tips. I just liked and subscribed. Great job💯💣🤘
thank you so much for the support :) , welcome aboard :)
what would be a good general lube or grease i could use for multiple parts ?
To be honest, i use what I have. Some are better than others just on regards of not coming off when water (rain) touches it. Some are water resistant. But when I use the ones that come off when water touches it, I just reapply sooner. I don't have a go to for general use. In the dealership there was a really good water resistant one but I can't remember the name of it
WD40 dry lube is great!
Come with me on a ride of pure imagination.
I maintain my machines in turn key status and pre flight control systems and general condition points each ride.
Happy Motoring!
Tyre pressure. OK here's what really annoys me about the dealer service department where I brough my bike from. the sticker on the swingarm states the recommended pressure for the factory tyres fitted to the bike, it has those very tyres fitted, yet when it was delivered to me the pressures were TOO HIGH and this made it slippery to the point of being dangerous. I reset the pressures and found that what was on the swingarm was pretty much exactly where they needed to be, so I had them EXACTLY where the needed to be for my weight and what I carry, which was what it said on the swingarm for the rear, and 1 psi less than the sticker for the front... And when I took it into the dealer for the first service they put the pressures at 10 psi above what they actually work well at. I'm so glad I felt it was wrong and stopped to fix it. because had I not done that I probably would have wiped out on the first ride!
Dealers should LEAVE the customers tyres ALONE... the OWNER and Rider finds the best pressure for they tyres> not someone who has never ridden the bike!
I will be specifically telling them NOT TO TOUCH MY TYRES OR THEY WILL BE REPLACING THE BIKE IF IT SLIPS OUT FROM BENEATH ME!
I should also mention I am a Mechanic who has been racing cars for 30 years. I know what I am doing, and the only reason I take my bike to the dealer for services is so they can't get out of any warrantee claim!
and then there's the oil change and how they did it, compared to how I told them to do it and referencing my qualification so they know they were dealing with a mechanic... did they spin the engine and trans up to free any sediment so it could drain out with the oil? No they did it cold when it had not been run in a while so all the fragments from machining and assembly could just sit in the engine and not be evacuated, so it can potentially damage the engine! this happens with many engines, and is why the first service is so soon after purchase!
I need to lube my clutch cable and my blinker fluid is definitely low as I have never checked it.🙃
Hello. Was wondering what year and model motorcycle you are riding now?
Great job. Love it. Subscribed mate.
Thank you.
just found out this channel, but do you run a bakery as well?
It is cool to see a fellow Eastern European biker chick do a bike maintenance video. I am curious what is a good starter bike? Harley or an Indian. I would like to have a bike that I can take cross country as well as a canyon carver. Any advise would be appreciated.
can't go wrong with either, in the end it all falls down to your personal taste and preferences. You should test ride a few at both dealers to get a feel for which you prefer. :)
Starter bike that is a great canyon carver and good for cross country doesn't exist, no matter what reviewers or salespeople tell you. An Indian Scout can do all three, but the cross country part will be that which it does most poorly. It also has too much power and weight to be a good starter bike. Stay under 200 KG nd under 50 KW while learning to ride.
great video !!! just subscribed
'Swan Lake', 'fleur-de-lys', 'Bach's Air on the G String'... bang goes your hard girl image ;-)
Hey hey, swan lake goes hard in the paint! 🤘😁🤘
Fun video to watch. Subscribed. Cheers!
you can come check my blinker fluid anytime lol 😉
Do you have a music list? Thank you for it.😊
Red or blue blinker fluid for Honda bikes ?
c'mon man, honda's get the orange one. red is ducati & blue is for yamaha.
I ride a Harley Davidson! What is this horse power thingy ya speak of? 😅
And I keep my brake lines bleeding & my brakes greased! Also my blinker fluid is always topped off, it's easy to do without using them. (jk)
On serious note, I'm amazed at how clapped the average used HD on market is. Lol
I thought buying from a dealer would save me from that hassle, but it hasn't 😅
Do you use OEM brake pads or do you have a favorite after market brand? What brake pads do you think are best?
so I have yet to experiment with aftermarket brake pads but in the future, I know I would like to, just to personally know and feel the difference. I use stock but from others who ride, I have heard the some aftermarket brake pads are a lot better and worth it over stock oem ones. That's a great question though, sorry I couldn't give you a better answer but in the future, I might have something better to say regarding that. :)
@MotoDasha no worries, I have good luck with H.D. pads. However I've heard some AM pads are much better as far as stopping power,but they don't last long. Whether that's true or not, idk.
Good tips.
Ha Haaa..😁😁 Blinker fluid indeed. Lots of useful info. Great !!
A little lube keeps things sliding smoothly !😁
Lol I still got the same tires on my 83 shadow. Lol bald as my head with chicken strips.
Do you have to wear that head band... Brett Michaels disapproves.
Your cute and your info is great!! Thanks
Very good md. I hit the subscribe button before I started typing. As a retired service manager and tech at a dealership the only thing I can add is the mission of hiring people with a functioning brain is almost futile. Any industry. I discovered that the bluer the arms, the least competent they tend to be. They have the wrong point of view, I think.
She is kidding, guys! If it is a Harley, the only thing you need to check for is the loose nuts, especially the one behind the handlebars!
No need to oil teflon lined cables.
where are you from dasha?
dont lube trottle cables or clutsh cables . cause on the lube will stick all dust and dirt witsh it will jam .
change the cables dont lube .
I bought one and its a 4 cylinder but soon after the head gasket started leaking 😭
Why measure oil when its warm?
Lube on the hinge
I don't know if this is helpful. I watched this video to see if you would demonstrate how to execute checking those important items you listed in your video. As fare would have it you didn't. Example: How you lube your throttle and brake cables, bleed your brake fluid. I'm just glad that you didn't mention checking the turn signal blinker fluid.
I like your content, but all the popups are distracting. Your videos are good enough without them. (Maybe not so many?)
Hey!! I appreciate that! I've been wondering I'd it was too much, and been considering toning it done. Thank you for saying something about em!!
The editing is great though 👌
I meen she cute its why i clicked lol
This video on 2x speed to get to the point.
I use blink 182 😂
My blinker fluid is died level.
Mine dried up from never being used
wd-40 is not lube....
Uh ... Latch?
over heating from running rich due to a clogged air filter? it would actually run cool, but you will notice a loss in power and an increase in fuel consumption.
She's right. Clogged air filter can lead to rich condition increasing combustion temperature and causing overheating in the chamber, valves, etc.
Media door.... immediately stops video. Bikes should not have these
Great information, but please stop with the memes / gifs / unrelated popups because your audience are not kids, and even if your audience was mostly kids, this amount of cringe is hard to handle and it's not building you an audience, which is a shame because you give good information, always consider your audience if you are serious about being a professional youtuber.
I am sure this advice is because you yourself run a successful TH-cam channel...
kinda useless thirst-trap video- a novice would not know how or where to actually check for these things
RULE #1. Never purchase a Harley-Davidson motorcycle.
If young people in the 60s, 70s did what you are doing, we would still be fighting the Vietnam war: avoiding sensitive national issues, avoiding following the money. On and on.
We’ve got a major publicly traded company taking money from motorcycle buyers, from stockholders, and giving it to this this this… Forcing dei down on employees who have to choice.
Are you ok giving your money to this this this? You have a say, you have a responsibility to step up. What do you stand for. No, instead, you are hiding behind a routine maintenance video. Please step up!
Theres plenty of videos about that . Go view them. This is a help;ful video.
@@northvanwan7428 Pathetic reply to the comment above.
@@tranceminder2WTh is wrong with you? She’s doing this out of a passion and is obviously qualified. This video has nothing to do with your poor dei rhetoric.
Good morning Trump nut job.
Yeh , i ride MOTOCYCLES not junk 🙄🙄👎👎👎👎
Without maintenance whatever bike you have turns into junk.
This is the most wholesome video I've watched that started with a woman stressing rhe importance of lube.
Can these bike’s go all the way to 2hundred miles or more like a car, I’m new with bike’s, somebody please if you know 🥹
the highest milage I have seen on a motorcycle was 150,000 miles approx. while I was a mechanic and it was in for a routine service. like cars, depends on how well you take care of the bike. And like cars, you can expect to do some repairs along the way to keep the life going. but typically, if taken care good, you can get 50,000 to 100,000 miles before you need to do any major work. Treat your bike poorly by not maintaining it right, ride is aggressively, not shift gears properly, you can expect issues much sooner.