Just installed this kit on a 2016 4wd. It went smooth but the inner tie rods ran out of adjustment and needed to be trimmed shorter to get the toe set correctly.
@@guadalupeacevedo7236 Kinda. Camber can be set, Toe maxes out so you cut the tie rods down then you can set it. But the front alignment bolt maxes out so you cannot get Caster in range.
I know this comment was over a year ago but using the spacer gives you a 4” drop and no spacer gives you a 5” drop. The spacer in effectively pushes your lower control arm further towards the ground giving you more height and without the spacer the control arm is higher towards the body giving you less height.
I have that same truck and the same kit you got there..! but I accidentally ordered aluminum/stamped and my truck has cast... can I just switch the upper ball joint to fit my spindle..?
Primo gracias x este vídeo, seguí tus instrucciones y tengo un problema el tornillo que ba en el lower arm que dojo el buje del nuevo arm es muy grande tiene garantía pienso que es factory problema.puedo poner un vídeo para que escuches el golpe cundo muevo pa tras o pa delante .
So I saw you have a spacer on the front arms, I’m assuming that’s where you can either get a 4” or 5” drop in the front? For a 5” drop you just put that spacer under the arm correct?
So question. I've got a 2018 regular cab short bed silverado that I'd like to lower, do I need a new driveshaft? Some people say yes and others say no.
The way that you drilled the upper spindle for the upper control arm can that be done to the bottom of the spindle as well for the lower control arm ball joint ?
On the 4/6 kit i believe you get 1" lifting shackles for the rear and the control arm can be adjusted to 4" by moving 2 ihc spacers under the strut and lower control arms
I have the kit installed on my 2016 Chevy Silverado crew cab, but the driver side control arms have been squeaking lately and I checked them and there fine not rips or nothing idk if it’s cuz the bushings are new but has anyone else had this problem?
IHC Suspension Hows the Ford Lightning, Ram Viper truck and Chevy SS lowered from the factory? Basically what I’m asking is how trucks are lowered from the factory? By control arms or spindles?
How do you replace the front stuts after this kit is installed? I tried the conventional way buy trying to pull them through the upper control arm and lower control arm with no luck...just a littlr too tight to get it out.
Best video I have seen how to install this kit on the new Silverados, thanks for doing it on the floor.
No problem 👍
you have to most detailed video here on youtube i love your work ivan please keep the great work coming
Just installed this kit on a 2016 4wd. It went smooth but the inner tie rods ran out of adjustment and needed to be trimmed shorter to get the toe set correctly.
We’re you a Able to get your alignment done?
@@guadalupeacevedo7236 Kinda. Camber can be set, Toe maxes out so you cut the tie rods down then you can set it. But the front alignment bolt maxes out so you cannot get Caster in range.
@@guadalupeacevedo7236 what did you do to get it trimmed I just had the same problem with mine
So question, no spacer on the bottom of the strut gives me the 4” drop? and adding the spacer gives me a 5” drop?
I know this comment was over a year ago but using the spacer gives you a 4” drop and no spacer gives you a 5” drop. The spacer in effectively pushes your lower control arm further towards the ground giving you more height and without the spacer the control arm is higher towards the body giving you less height.
I installed everything, but my sway bar link doesn’t line up straight thru the control arm, how can i put it on not lining up?
My sway bar end link is way shorter than that and it does not line up with the control arm what do I do?
same here
what did you end up doing?
If anyone has the same issue, you have to put them on with the truck on the ground after you install everything else
Did you ever find out?
@@alexramirez8096did you find out how to fix?
Whats the part number for replacement 2018 ball joints
Where’s the step when you cut the tide rods?
I’m saying. No one ever mentions that.
Need a video on cutting the tie rods….. nobody ever mentions it still till this day IHC
I don’t think u need too
I have that same truck and the same kit you got there..! but I accidentally ordered aluminum/stamped and my truck has cast... can I just switch the upper ball joint to fit my spindle..?
Send email to tech@ihcsuspension.com
What’s the point of removing the strut why didn’t you just take off the 2 bottom bolts?
31:37 what is the strut spacer for???
You guys have a guide for the torque specs on the upper/lower control arm
How long is that sway bar link, the bolt I got looks way shorter than that
Mine too. I have the short gold ones. Had a hard time getting them on but it worked out.
If i want to do a 4/6 drop on my 2012 silverado 2wd do i need a c-notch?
Manuel Favela you don’t need it
I just installed this kit this weekend and mine bottoms out a lot. Looking to get some bags to see if it helps
Installed this on my 4x4 very easy to do on ground!
Did you have any issues like with the spindles? And how low did you go? I want to do the same to my 4x4
@@cabreramiguel52 No problems at all was easy installment and went 5 inches lower
@@cabreramiguel52 hardest part will be the flip kit in the back if ur doing it alone. other than that it wasnt bad at all
I have a crew cab 4x4 on 3” springs only up front. I hate it Gonna try these out
Hey did you have to cut your tie rods?
Primo gracias x este vídeo, seguí tus instrucciones y tengo un problema el tornillo que ba en el lower arm que dojo el buje del nuevo arm es muy grande tiene garantía pienso que es factory problema.puedo poner un vídeo para que escuches el golpe cundo muevo pa tras o pa delante .
Do I need both lower and upper arms to drop my truck, will 3" upper control arms not drop it 3"
Is the lower ball joint the same as the stock gm one that’s on the truck? Just wondering for replacement purposes
How i know what kind of control arm my truck have?
my kit 3/5 for my 2021 came yesterday lol i was gonna have Switch here in phoenix install it but they're booked all year
I might’ve missed it but with the strut installed is that a 5 or 4 in drop?
So I saw you have a spacer on the front arms, I’m assuming that’s where you can either get a 4” or 5” drop in the front? For a 5” drop you just put that spacer under the arm correct?
So question. I've got a 2018 regular cab short bed silverado that I'd like to lower, do I need a new driveshaft? Some people say yes and others say no.
I have never heard of shorter drive shaft I been lowering truccs all my life
Kevin Pazos lowered my 93 single cab & my 2010. & my cuzins 05. I’ve never heard of that 🤷🏻♂️
Is it possible to do the 5/7 drop instead of 4/6 on a 4x4 16’ Sierra ?
Yes
The way that you drilled the upper spindle for the upper control arm can that be done to the bottom of the spindle as well for the lower control arm ball joint ?
No just the top gets drilled out.
That host is one informative cool cat 👍
I’m installing the 3/5 kit on Silverado, will using the strut spacer give you 3” or 4” up front? Thanks
I thought you guys were gonna start doing more on TH-cam? Anything you guys upload from the shop ppl Gonna want to see..
What’s the torque specs for an 08 Silverado control arms
Which ones do I buy if the truck is 4x4? It’s also 2015 1500 single cab just don’t know if it’s different ones because it’s 4x4
once your on there site it asked if its 4x4.single cab etc.
What about the taper cone , that comes with the kit??
How do I put the spindle back on after installing parts if it’s a 4x4?
Can i get the model of the shocks please
If i got this kit for for 2015 silverado reg cab 2wd i live in north Ga if i drove the truck there how much would you charge me to put it on
Just do it your self. Not worth the trip. Very easy if you follow this video. I did it in 1 day I never done this before. Great tutorial video
Do u guys just sell the 2" drop shackles 18 silverado single cab
When the control arms where silver where those the first ones also what’s the ball joint part #s for 17 Chevy single cab stamped control arms
Did u find it
Is this kit only for 2wd? I want to drop my 2011 4x4.
Looking for a 4/6 this help a lot trying to do a drop on my gmc 2014 Sierra crew cab how much on the kit ,,,,
My control arms nor my ball joints came with the nipples installed 🤦🏻♂️ i realized it when i was ready to grease them
Where you got ur c notch
Do you need a c notch for a 2018 gmc 5/7 drop?
What problems do you run into if your truck has been in a wreck ?
Jr mainly fitment issues and truck not aligning if truck frame is bent.
So how many ugggaa duuggaasss do u need to use for bottom control arm.
Jk
I want to order one for my 2017 this video is a big help
2014 silverado 2wd single cab. you have a 4/6 and a 5/7 kit on your website. It shows the same parts. what the difference
On the 4/6 kit i believe you get 1" lifting shackles for the rear and the control arm can be adjusted to 4" by moving 2 ihc spacers under the strut and lower control arms
Are the control arms narrowed a bit to tuck rim ? I have a 94 c1500 and the driver side sticks out more than my passenger.
Our 88-98 control arms are a little shorter than than stock. About 3/4 of an inch.
How much would it be if I ordered it and for y’all to install it?
How long does this process usually take?
Any difference with the 2019?
Yes sir we have a separate kit for the 2019s
@@ihcsuspension2758 what about if you have the aluminum spindles would this kit work with aluminum spindles ???
Where are you located? Where can l get that suspension for my 2019 2wd f150?
I like to purchase 4/6 one!!
ihcsuspension.com/shop?product_brand=Ford&range=2015-2018 use ozuna2020 at checkout
Anyone knows what size is the middle nut on the rotor for 2016 GMC Sierra 4x4
36MM
Do you guys include new u bolts for the flip kit?
No sir, we do not include u bolts. We use the factory u bolts, with our kit.
How much is this kit without the helper bags
Hello Tenorio, we sell everything individually we have all pricing on our website www.ihcsuspension.com
How much is a 5/7 kit? What city are you in?
Great video can’t wait for more
Coming soon!
Did u have to shorten ur driveshaft when u lower it
no sir.
Okay because I'm going to do a 4/7 drop
I have the kit installed on my 2016 Chevy Silverado crew cab, but the driver side control arms have been squeaking lately and I checked them and there fine not rips or nothing idk if it’s cuz the bushings are new but has anyone else had this problem?
I have a buddy having this problem, we haven’t figured it out yet, I’ll get back to you tomorrow with mor discovery!
By the way awesome job 😁
Thank you so much 😀
Did you guys fixed the ball joint issues on the control arms? I keep hearing bad reviews about ihc..
Were u located bro
How bout 99-06 Silverado?
Fuck I skip that step on greasing the upper n lower walls just grease them thru the fitting 🤦♂️ I’m new on changing out suspension
do the spacers that come with the kit is it to make it drop an inch more or drops it more?
You can go either way putting everything the kit comes with to make it a 4/6 or no spacer and factory hanger to make it a 5/7.
Can I use the stock strut
Yes our kit is designed to use your factory strut assembly and oem spindle.
So does the spacer on the shock give you 4” or 5” drop when installed ?
With the spacer in, its 4" drop.
@@afterhoursfab how thick is the spacer I didn’t catch tht
@@BuiltTrucks It's about 1/2" thick but since its in the middle of the arm it will give 1" lift/drop at the wheel
@@afterhoursfab thanks good to know
How much for the kit 2 and 5
we don't do 2/4. We have a 3/5
Where you guys located ?
Palmview TX
Please do one for the 3’ lower control arms only.. i already have 2/6 flip kit but horrible camber so i ordered the IHC 3’ lower arms
The 3 inch arms, all it is. Is the lower control arms install.
Great video, but need more in depth on where screws are being placed.
Bad ass kit only thing I hate is the amount of turning you lose with those arms
Kits have been revised.
IHC Suspension Hows the Ford Lightning, Ram Viper truck and Chevy SS lowered from the factory?
Basically what I’m asking is how trucks are lowered from the factory?
By control arms or spindles?
BEST KIT OUT THERE 🔥🔥
Roberto Garza thank you sir
💯
aren't you supposed to TQ them ? and not just crank on them
Nice video I want to see some rams
Coming soon
Less talking, more doing
How do you replace the front stuts after this kit is installed?
I tried the conventional way buy trying to pull them through the upper control arm and lower control arm with no luck...just a littlr too tight to get it out.