I like it keep up the good work KING of prelude coming out soon..just stuck right now down low trying to take out old bolts to put in ST sway bars,strut bars,lower control arms,tien suspension & DEFC and last brakeline
Nice job. I don't feel so bad about my OCDness now. 98 Base Lude, 2020 Boost Blue Pearl, Spoon Sports Front Lip (rare). I should probably do a video too lol
they're 17x9.5 +30. camber, I don't remember, probably about -2 degrees. In my opinion, this fitment only works if you lower your car and camber the wheels. As of now, my wheels arent cambered and the lude is raised up a little because of my new coilovers wont allow me to go any lower, so the fitment look ehhh compared to how it looked in this video
SHOUTS! gotta '98 Pelude in the garage that I'm about to get RIIIIIGHT!!! Also, I noticed on some supercars the have plywood undercarriages. Thus, I'm putting plywood under my lip.
Did you ever figure out what that rattling noise in the tear end was that you said started when you first drove it after you put the coilovers on? I have a 99 prelude sh and it makes that same rattling noise in rear end even if I’m only going like 5 miles an hour.
@@Rawrkee it was around 5:50 mark in the twin coil over video. Not this video, I was going threw your vids seeing if you talked about it again but I haven’t seen anything. The vid says 4 months old.
@@Rawrkee did you see the message in the other video? The video is only 7 min long and it was right after you put your coilovers on you drove it down the road and you said right away that it was rattling in the back and you hoped that you could figure it out. The title of the vid is Tein coilovers on the lude
@@Rawrkee I'm running Stanceparts for the past 4 years. Replaced the air valves that came in the kit for some uprated ones that allow me to set the height (or pressure rather in the cups) to have smooth aired up driveability, so I can now use them as if it was a bagged setup but with the benefit of having the rebound rate of a coil spring
@NoMore Time I disagree, the further he is able to get the front into the roadway the more clearance he'll have at the point the wheels go off the wood. The way it currently is the planks are still at a slight dip and the car comes off too early. In the side ways action he does towards the end it's fine, but if he wanted to go out straight then lengthwise would be better. I have the same issue at my GF's place
I need help from the prelude world,I am in need of the rear low control arm left and right,i want them brand new but a friend of mine said there discontinued and thays is not a good thing for me i am trying to get those brand new or use in perfect shape....need some help from the prelude world...any good info contact me at ttaappout@gmail.com or drop info here THANKS alot
@@midniter2001 thanks been ebay buy 20 years now so I am alwayz on there,mine is the base and the rear is hard to come by they have use once on ebay now and want 170 use and beat up but honda dealers and other cant get it all disconnected,so I am trying I hard i wish I had a direct connection to japen speed store
WE LOVE UR ATTITUDE AND UR BUILD MAN UR INSPIRING PEOPLE LIKE ME WHO HAVE A 94 ACCORD BUT ARE DETERMINED TO MAKE IT A RACECAR!!
Anytime I see a clean Prelude it brings a tear to my eye.
That lip looks great! Would love to find the same sort of addition for the sides and rear...
Can u post the link to the front lip u got! Looks gooood!
old skate board trick use bondo to create a ramp. paint it black to look like asphalt. can always just chip it up.
denggg, that's a creative idea, I'll have to try it out one day!
I like it keep up the good work KING of prelude coming out soon..just stuck right now down low trying to take out old bolts to put in ST sway bars,strut bars,lower control arms,tien suspension & DEFC and last brakeline
Iron Man gahhh deng, you def puttin in WORK!! Keep up the grind bro!
@@Rawrkee alot of work but I truelly luv it,give me a rushhhhhhh
Canada here playa! Passat lip n spoiler on my 89 rex...it's all good, do yo thang, keep turning that wrench... one love
Diggin the Prelude! If you can, just buy some cement and fill-in the bottom of your driveway
The bb6 is straight 🔥
I want tp see more prelude pictures put there
Damn, front lip looked good on Prelude!
George Gomez it’s now a subralude! 😂
@@Rawrkee Hahaha 😂
What size wheels are you running? Offset, width?
I saw your TH-cam channel on the back of your truck and I’m impressed (:
Hansen McDonnell ayeeee, thanks man! :D
Can u send a Link/or the name of the Lip For the honda ? I would Appreciate it
Check the video subscription, I found a few links for you
Bro good stuff! I wanted to do that before the kbd bumper. I really like your interior aswell
Elias G chyeahhh! Thanks bro!
Nice job. I don't feel so bad about my OCDness now. 98 Base Lude, 2020 Boost Blue Pearl, Spoon Sports Front Lip (rare). I should probably do a video too lol
Spoon sports front lip!? I've never heard of that, you def gotta post a vid and send me some pics :D
finally another lude owner, subbed ;)
That thing looks clean bro. Nice.
That new lip is sick bro!!! Great choice!
how do i get this body kit?
what rear and side skirts did you have on it in this video? i need them
I want a link to the subie lip also! Not trying to give it out?
Where did you get your front prelude lip ?the one that is already wrapped red
L J OEM front lip from Honda. Snagged one whole they were still in stock
Rawrkee oh dang nice 👍 gotta get one for mine the front looks naked without one
m.th-cam.com/video/pVm6Zjbk8vA/w-d-xo.html
@@LJ10650 check out aeroworks, they sell high quality replicas of the greddy, oem and wings west lips. im gonna get a wings west lip kit from them
Hi. Atts system works fine if you have prelude so low?
I must have miss it from your older videos but what your wheel spec: +22, the camber? Are those 18 x 9? Thanks in advance.
they're 17x9.5 +30. camber, I don't remember, probably about -2 degrees. In my opinion, this fitment only works if you lower your car and camber the wheels. As of now, my wheels arent cambered and the lude is raised up a little because of my new coilovers wont allow me to go any lower, so the fitment look ehhh compared to how it looked in this video
What year subie lip is that from
What year and make of Subaru you got the front lip from?
How did you know this would fit?
I couldn't help it dude, you need a valve adjustment. My CB7 H22 almost sounds like yours. Clean prelude.
What color is that man? It looks sweeeeeet!!!!! Btw how did you get a fob for ur lude?
Where you get your headlights?
Professor Xavier's TH-cam account for the gifted it was a DIY project, I used g35 projectors in DEPO headlights
SHOUTS! gotta '98 Pelude in the garage that I'm about to get RIIIIIGHT!!! Also, I noticed on some supercars the have plywood undercarriages. Thus, I'm putting plywood under my lip.
Bruh! I change my master clutch and slave, did the bleed but when I start the car I cant get into gear, it goes when its off
Ahhh man, I've never messed with the clutch and slave cylinder, try hitting up the Facebook 5th gen groups
Looks great! Where did you get the headlights from and the seats?
Headlights were custom made using G35 projectors. Seats came from Canada, a nice find on eBay
@@Rawrkee Awesome! Thank you for replying.
Damn my g , rocking dat buzz cut! 👌👌👌
Is that the hfp front lip
@@rockeyvang1045 yes, it’s the optional factory lip
Where did you get the headlight eye lids?
Did you ever figure out what that rattling noise in the tear end was that you said started when you first drove it after you put the coilovers on? I have a 99 prelude sh and it makes that same rattling noise in rear end even if I’m only going like 5 miles an hour.
Are you referring to around the 9:06 mark? That’s my passenger side interior door lock that rattles loudly
@@Rawrkee it was around 5:50 mark in the twin coil over video. Not this video, I was going threw your vids seeing if you talked about it again but I haven’t seen anything. The vid says 4 months old.
Tein not twin
@@Rawrkee did you see the message in the other video? The video is only 7 min long and it was right after you put your coilovers on you drove it down the road and you said right away that it was rattling in the back and you hoped that you could figure it out. The title of the vid is Tein coilovers on the lude
@@notacoyote2790 if you have adjustable dampening, it should help. I think I made mine more softer and it runs a bit quieter now
Is the car wrapped or painted?
Fyee when you gonna wrap the door lol 😂
naim abdool man, I’m a really dude hahah
Is this the same car that got hit recently?
yeahh :/
@@Rawrkee damn man smh. Hopefully you'll get her patched up. She's hella clean
post more prelude content
give a hint, lay the boards along the car, not across
Alternatively, get some air cups for the front ;-)
Techniq_BB6 yoooo!! I’ve def been thinking about that!!! Any recommended brands???
@@Rawrkee I'm running Stanceparts for the past 4 years. Replaced the air valves that came in the kit for some uprated ones that allow me to set the height (or pressure rather in the cups) to have smooth aired up driveability, so I can now use them as if it was a bagged setup but with the benefit of having the rebound rate of a coil spring
Bro why you laying those planks horizontal? Lay them in line with the tyres as you are coming off the driveway to give you more length the road way
Techniq_BB6 damn, I never thought of that 😂
@@Rawrkee lol, hope it helps. But I see you got out the driveway nicely with that sideways action
@NoMore Time I disagree, the further he is able to get the front into the roadway the more clearance he'll have at the point the wheels go off the wood. The way it currently is the planks are still at a slight dip and the car comes off too early. In the side ways action he does towards the end it's fine, but if he wanted to go out straight then lengthwise would be better. I have the same issue at my GF's place
Looks wicked man!
But seriously, is that off a WRX
? What year?
Yuhhh and it’s 06-07 check the description
I think if you are serious about lowered cars you should break up that concrete and re-do a proper entry like a boss. 😎
I need this Seats
Keep an eye out on ebay! Mine came from Canada
Car is clean. I really enjoyed the video. Keep it up boss.
Is your front lip oem or eBay?
It’s OEM but you can use an OEM style lip
Cleeean 🔥
What rims do you have?
They’re varrstoen es2
lmao my prelude has the exact same vibrating sound inside and its driving me insane
I'm not sure yet but I think you need to do some maintenance on your coilovers if you have a set installed
I need this car, how do i get this?
You can get the lip off eBay
Looks sick! Keep it up 👍🏽👍🏽👍🏽
Diffuser under the lip. Lol
love ur style bro and you said "Lude" exactly how u should hahaha
u also need to come to europe to style my Lude exactly like this one ;)
nice look
NIIIIICE 🔥🔥🔥🔥
🔥
Sweet Lude.
Finish the wrap ffs lol 😂
SLicKriCk B But the driver side looks fine 😂😂😂😂
NICE
👍
I need help from the prelude world,I am in need of the rear low control arm left and right,i want them brand new but a friend of mine said there discontinued and thays is not a good thing for me i am trying to get those brand new or use in perfect shape....need some help from the prelude world...any good info contact me at ttaappout@gmail.com or drop info here THANKS alot
Plenty of base model LCAs out there in junk yards on marketplace eBay etc, hard to find type sh ones. Just depends on make model etc. eBay is my go to
@@midniter2001 thanks been ebay buy 20 years now so I am alwayz on there,mine is the base and the rear is hard to come by they have use once on ebay now and want 170 use and beat up but honda dealers and other cant get it all disconnected,so I am trying I hard i wish I had a direct connection to japen speed store
Oh lol
Just buy air suspension problem solve lol
400th like
You da man 💪🏼💪🏼💪🏼
моя первая машина))) prelude V))