Просто замечательно, что выводы сделаны в одну полоску, которая будет сильнее всех греться и может перегореть. Надо усилить ее, или допаять провода с разных участков
Bro, very nice video. But I read in the comment section that you have modified the charging in the ups to charge the lithium battery pack properly. It would have been really awesome if you had explained it along with the battery pack making or made a new video cause it may be misleading for many of not pointed out that lead charging system is different from Lithium ion technology.
Instead of using normal batteries you could have used 5 amp li ion batteries which are also available yes they are 18650 and only 6 cells would have been needed to create 12v 10 amps battery pack and the ups is not made to charge li ion batteries let me tell you use a simple charger pcb and connect the 12v input of ups to the pcb circuit it will help to keep them safe along with the bms
It worked fine, but please check that the charging system of the UPS device may not be suitable for the lion battery. You have switched from a dry type battery to a different type of battery.
Не делайте так, логика работы контроллера бесперебойника не расщитана на контроль литиевой батареи и просто заменить свинцовую на лицевую черевато пожаром взрывом лития и никакой драйвер не поможет. Так литий не любит перезаряд, а в бесперебойника свинцовые постоянно под зарядом стоят. Так что как минимум бесперебойник должен контролировать батарею и при полном заряде отключать ее. А в случай отключения питания она должна подключаться. Так что с такими вещами можно без дома остаться.
Есть грамотное решение этой проблемы в виде снижения конечного напряжения заряда до 12 Вольт. Причем именно до 12, а не 12,6, чтобы аккумуляторы не находились постоянно под максимальным напряжением. Я ставил литий в бесперебойник 1000ВА. Там используются 2 свинцовых аккумулятора, соединенных последовательно. Напряжение заряда по 3,9В на банку при использовании батареи из 7 секций по 4 банки. Полет нормальный. Встроена плата ВМС с контролем состояния по блютуз.
Please do not let the UPS charge the Li-Ion 3S Battery. The 3S has a nominal voltage of 11.1V and a maximum of 12.6V (4.2V per cell row) - The UPS will attempt to charge the battery on the Pb voltage standard which is 14.4V. This will take the cells way over 4.2V and the BMS will probably burn its resistors as it will attempt to stop the current from passing, entering the "overvoltage" mode. If you don't do that, at least pin this comm so that people won't do it either. Thank you. Nice pack, btw. :D
As you make a pack, when connecting in Parallel which way is better way connect it in? Connect it in as square ■ or connect it in as straight Line ----!
no fuse on each cell means.. if one gets bad meaning short.. high current will flow from other batteries that are in parallel and we know how will it end in that case
Lithium ion batteries need a CC CV charger to fill their juice. Others may lead to an explosion. The way of handling 18650 lithium ion batteries is needed to be safe.
Ese no es problema. La ups solo permite de 350 a 500 ma para cargar la batería. El problema que yo veo es, 1, que el pack soporte la misma descarga que la batería de acido plomo. Y 2, que la ups maneja mucha temperatura por el trasformador, la cuál eventualmente llega a la bateria. Cuando se termina la carga de la batería de acido plomo con una PC , esos cables se sienten muy caliente(+ y -). Me da miedo que esa batería vaya a hacer explosión en algún momento por temperatura
That's not the problem as your laptop and phone gets even much hotter than this during high operations. My main area of concern is that the pcb should have thermal cut out sensors or sensors that can be attached to the battery body from the pcb. Like we have a laptop and power bank batteries.
Lead-acid batteries use the (CCCV) charging method. so ya can replace them with lithium batteries. plus the IC board is going to protect and maintain the cccv more accurately
Yeah, I will say, I don't understand exactly what the circuit they added does or how. But i do know messing with home made battery set ups, lead to lithium battery explosion and fires. I'm sure there are safe ways to do this, but...not being an expert, I can not tell if just adding the circuit makes it as safe as factory made batteries, that are made under approved factory safety standards. This maybe okay, but it also may not, so i personally wouldn't buy or make this.
puro fresh kaaj korechho tumi, tobe ki ki korchho, ki ki lagachho, kivabe lagachho,,,paralal na series ei gulo kullekh kore dile aaro valo hoto. great work.
I tested 5 brands UPS crarge only 13.53~13.75V. The bms will cut charge when battery 12.6~12.9V. But UPS will stop output too early when battery still have energy but volter is low for Lead-Acid Battery.
we can't charge Li-ion battery pack with Lead acid battery charger so I had to modify the charging circuit of UPS so we can get appropriate charging voltage and current.
🎉 I will try. How much tries before a successful battery pack :-)) 😊 First, to gather proper tools. Come back next year after many trials and dispointments (if still alive 😂). To thanks gor this very good pedagogical video.
Good afternoon Tapedra My name is Laerte, I'm from Brazil, I would like to buy the PCB board already assembled to solder batteries, but I don't know how to configure it on the website to order it on the website. If you can help me or sell me one already assembled. Gratitude
My Ups gives continues ticking (not beeping) sound and not charging. I opened it and I think,sound comes from relay. I don't know the problem. Also tested the voltage at battry charging point it is 6v . Please help me.
The charging voltage to the battery is much higher than Li-on. Batteries can even explode from high voltage. Even if he can shoot video, there is a fire in people's houses, so what?
Wow, sounds like a game-changer for anyone looking to elevate their video quality! Thanks for sharing!
I remember you from newspaper. Good to see you back.
D
Anh đóng pin rất chuyên nghiệp xin cảm ơn đã chia sẻ với khán giả
Просто замечательно, что выводы сделаны в одну полоску, которая будет сильнее всех греться и может перегореть. Надо усилить ее, или допаять провода с разных участков
It looks simple to do it, let me try how simple it is for me , I will do this weekend! Nice video
How did yours go
It will work for a very short time because the rated voltage of the UPS is between 12 and 14.5v. This battery can't even put out 13v.
But there is no ways out
You are a professional so you did it easily but please tell that how dangerous it can be if even a small mistake is made.
Bro, very nice video. But I read in the comment section that you have modified the charging in the ups to charge the lithium battery pack properly. It would have been really awesome if you had explained it along with the battery pack making or made a new video cause it may be misleading for many of not pointed out that lead charging system is different from Lithium ion technology.
It will work for a very short time because the rated voltage of the UPS is between 12 and 14.5v. This battery can't even put out 13v.
I loved your video, thank you.
Instead of using normal batteries you could have used 5 amp li ion batteries which are also available yes they are 18650 and only 6 cells would have been needed to create 12v 10 amps battery pack and the ups is not made to charge li ion batteries let me tell you use a simple charger pcb and connect the 12v input of ups to the pcb circuit it will help to keep them safe along with the bms
Nice upgrade from lead battery to liion battery pack
very good work master
I learned a lot from you,you are very genius 👍👍👍
The good thing about doing this is you can get high quality batteries..
What about coolant to avoid overheating and fire?
It worked fine, but please check that the charging system of the UPS device may not be suitable for the lion battery. You have switched from a dry type battery to a different type of battery.
Very good 👍 ❤ Allah ap ko ترقی dy
Terimakasih banyak kak atas ilmunya semoga bermanfaat untuk semuanya aamiin
Is this 26700 battery cell?
video của bạn thật sáng tạo ❤❤❤
Great!
Wow excellent
But it's need charge how do we do???????
Excelent content
Homemade battery cell welding machine Ideal, thank you for sharing
What is the name of the device you are using to join (solder) the component to the battery.
amazing video
Не делайте так, логика работы контроллера бесперебойника не расщитана на контроль литиевой батареи и просто заменить свинцовую на лицевую черевато пожаром взрывом лития и никакой драйвер не поможет. Так литий не любит перезаряд, а в бесперебойника свинцовые постоянно под зарядом стоят. Так что как минимум бесперебойник должен контролировать батарею и при полном заряде отключать ее. А в случай отключения питания она должна подключаться. Так что с такими вещами можно без дома остаться.
Есть грамотное решение этой проблемы в виде снижения конечного напряжения заряда до 12 Вольт. Причем именно до 12, а не 12,6, чтобы аккумуляторы не находились постоянно под максимальным напряжением. Я ставил литий в бесперебойник 1000ВА. Там используются 2 свинцовых аккумулятора, соединенных последовательно. Напряжение заряда по 3,9В на банку при использовании батареи из 7 секций по 4 банки. Полет нормальный. Встроена плата ВМС с контролем состояния по блютуз.
Уважоемий товарщ ни видищ в нутри батарейка щто паял а там схема Целий . Успакай Ся он сдел л. Шидевур
@@edmarkota есть готовые платки на алике через 2 припоя, 11.98v , 12v сокращают срок службы l-ion
Please do not let the UPS charge the Li-Ion 3S Battery. The 3S has a nominal voltage of 11.1V and a maximum of 12.6V (4.2V per cell row) - The UPS will attempt to charge the battery on the Pb voltage standard which is 14.4V. This will take the cells way over 4.2V and the BMS will probably burn its resistors as it will attempt to stop the current from passing, entering the "overvoltage" mode.
If you don't do that, at least pin this comm so that people won't do it either.
Thank you. Nice pack, btw. :D
quá hay nha bạn :)) Good
Super!
Nice!
Est-ce que vous pouvez nous donner la référence de plaque électronique utilisée ici?
Great thank you... Please What is the name of the welding machine you use
Bhai ji battery ke upar plate lagaya hai use ham kis naam se le sakte hain market mein
Bms
nice video❤
As you make a pack, when connecting in Parallel which way is better way connect it in? Connect it in as square ■ or connect it in as straight Line ----!
no fuse on each cell means.. if one gets bad meaning short.. high current will flow from other batteries that are in parallel and we know how will it end in that case
Lithium ion batteries need a CC CV charger to fill their juice. Others may lead to an explosion. The way of handling 18650 lithium ion batteries is needed to be safe.
:
Ese no es problema. La ups solo permite de 350 a 500 ma para cargar la batería. El problema que yo veo es, 1, que el pack soporte la misma descarga que la batería de acido plomo. Y 2, que la ups maneja mucha temperatura por el trasformador, la cuál eventualmente llega a la bateria. Cuando se termina la carga de la batería de acido plomo con una PC , esos cables se sienten muy caliente(+ y -). Me da miedo que esa batería vaya a hacer explosión en algún momento por temperatura
That's not the problem as your laptop and phone gets even much hotter than this during high operations. My main area of concern is that the pcb should have thermal cut out sensors or sensors that can be attached to the battery body from the pcb. Like we have a laptop and power bank batteries.
Lead-acid batteries use the (CCCV) charging method. so ya can replace them with lithium batteries. plus the IC board is going to protect and maintain the cccv more accurately
Yeah, I will say, I don't understand exactly what the circuit they added does or how. But i do know messing with home made battery set ups, lead to lithium battery explosion and fires.
I'm sure there are safe ways to do this, but...not being an expert, I can not tell if just adding the circuit makes it as safe as factory made batteries, that are made under approved factory safety standards.
This maybe okay, but it also may not, so i personally wouldn't buy or make this.
ofarin super
Nice👌 video👍👍😍
puro fresh kaaj korechho tumi, tobe ki ki korchho, ki ki lagachho, kivabe lagachho,,,paralal na series ei gulo kullekh kore dile aaro valo hoto. great work.
Lithium ion cells cant be charged like lead ones, max voltage is 12.6 for 3s and ur putting around 15v, it will burn the bms
I tested 5 brands UPS crarge only 13.53~13.75V. The bms will cut charge when battery 12.6~12.9V. But UPS will stop output too early when battery still have energy but volter is low for Lead-Acid Battery.
I have a question: charging a lead acid battery and charging a Li-Ion battery pack(12v) with BMS needs same voltage and current ?
we can't charge Li-ion battery pack with Lead acid battery charger so I had to modify the charging circuit of UPS so we can get appropriate charging voltage and current.
@@tapendramandal Brother, in that case you must warn makers about it. With all due respect to your creation.
Hello dear sir it's okay respect I love your ideas 😊😊
Kop sondor
How are you going to charge this without properly balancing each cell?!
Bro Which website/online store is the best for Li ion battery and BMS? Pliz suggest.
please what is the total ah of batteries and what is the capacity of BMS you used?
🎉 I will try. How much tries before a successful battery pack :-)) 😊 First, to gather proper tools. Come back next year after many trials and dispointments (if still alive 😂). To thanks gor this very good pedagogical video.
good@
I want to build a 24V-500watt battery for a wheelchair, and I don't know how to assemble them, if you have a sketch please, thank you
How many hours of back up??
Good work bhai
men gaham yasab bering pulini beraman ...UZBEKISTAN
perfect
ı think you have changed your old videos was more fastinating and brilliant.
👍
Pls what the name of the machine that you are using please
Super
Series connection or parallel
good job
Mujhe 60v ki lithium ion battery esi bnwani hai how many cost
สุดยอดเลยครับ
Thank you
Vc tem bastante fita de níquel
What's the size of Nickel Stripe You used that allows this welding without any Problems??
Gostaria de saber da máquina de solda? Pode me mandar o passo a passo, como fazer?
Too good 👍👍 😊
Pilleri puntaladığın puntanın Malzeme listesini verebilir misin teşekkür ederim
Bhai 18650 battery pack ups use kar sakty hain
*Doesn't anyone sell battery holders there?*
BMS nicht angeschlossen ????
How did you build the welder?
They do sell spot welder in Ebay, Amazon and ....
Dimana cari batry nya itu?
nice
volt to tek leken ampar A kitny hy koi ptanai
What is the maximum instantaneous current that the package can supply at 12Vdc? Can you start a car engine in an emergency?
Normally it's possible, but dangerous
No Balance wires connected...!!! Use Thermal Tape next time... Heat resistant tape.
Please can i get this battery already constructed one's in the market??
And what battery name would i tell them that i am looking for??
16850 लिथिनियम
3.7वोल्ट
Sbalam silaturahmi
Sir pls make hand cantrol dron❤❤
Why output voltage is 167V?
The UPS outputs a modified sine wave. Simple multimeters see only the lower threshold of the wave
Kitna kharsha aaya...?
Ukuran berapa batry inya?
المواطن لا يعرف الفرق بين صنع بطاريه الليثوم الاصليه وغير الاصليه ان كان هناك فرق صناعي والسعر وايهما افضل
Wowo
بما لا توجد ٥رق بين شراء جديد وبين تبديل اجزاء البطاريه ولم يذكر الفرق والأسعار مع الشكر
Bro ware to buy this material.
You can collect them from an old laptop battery
Thanks 🙏👍
Single Battery How much cost
Good afternoon Tapedra My name is Laerte, I'm from Brazil, I would like to buy the PCB board already assembled to solder batteries, but I don't know how to configure it on the website to order it on the website. If you can help me or sell me one already assembled. Gratitude
My Ups gives continues ticking (not beeping) sound and not charging. I opened it and I think,sound comes from relay. I don't know the problem. Also tested the voltage at battry charging point it is 6v . Please help me.
Probably there is some short circuit on pcb or damage component
@@tapendramandal I think battry is dried out, put some battry watter, but that didn't work.
When I change the battry with another one ,output is good working, but not testing with charging, because that is a lithium ion cell pack ,
nice ❤❤❤
NIKLE STRIP GET WHERE FROM ANY LINK
Give at least 150.watt load on UPS and show
محتاجهم أين تباع
BRO BMS KITNA AH KA HEI?
😎😎😎😎😎😎😎😎
The charging voltage to the battery is much higher than Li-on. Batteries can even explode from high voltage. Even if he can shoot video, there is a fire in people's houses, so what?
Where is the input charge😮
Sir charjing PCB kahani se milega
You can search 3cell BMS online
Bro es baitari ko hame de do kitane rupay Dene honge❤