When you grow up with feet and inches, it just makes sense. You can be just as precise with Imperial as you can with Metric. Maybe the math is a little easier with metric, but that's why we have calculators.
I find the math of imperial to be easy once I became an experienced woodworker. Example (quick math in your head): 1167mm+886mm= VS 18 1/8 + 56 7/16=…….. imperial is quicker in an instance like this. I do really like metric though and if one system were only to survive it probably has a wider range of applications and ease
Upon unboxing, I was immediately upset at how the rails were very noticeably bent. But I kept going, all tools needed to assemble were included th-cam.com/users/postUgkxqtX4Dxs6aecAZEuz6GY5-d81YecKCshn and I had it set up in about 30 minutes. Honestly I love this thing, make sure to read the measurements and measure your space so you know if it'll work for you. I bought this to put inside my closet, underneath where I hang my clothes and it is absolutely perfect! It is VERY sturdy and all drawers glide easily and mine are stuffed, and they are still flush when closed.
Probably one of the best explanations on how to properly build sliding doors I've come across... even if you don't make fine furniture and only shop cabinets. Great presentation and video production.
Chris, I think you read my mind. Every time I have an idea, you drop a video on the exact topic I'm looking to learn more about. I've built two of your designs now, and always feel confident following your instruction. Thanks for everything you do.
I just built my first sliding door cabinet and your tips helped a lot, 80 x 36 x 13 inches deep. I aimed for 3/4 overhang just like you recommended. The sliding doors are 40 x 33 and I used half inch and there bowed but it’s a shop cabinet and it’s practice for the real furniture I’ll build for the house. My shop is 1.8 metres wide by 4.8 meters long, super small shop in Dublin, Ireland 🇮🇪
I don't own a table saw nor router, but I am subbing right now! Why? This guy is so down to Earth. He doesn't skip or race through project. I recently bot 2 Bluetti AC300s & 2 B300s. I can't find a cart, rack or cabinet that will properly fit my power station. Because I live in rural America & keeping my Power Station in my outdoor kitchen (once I install a Transfer Switch (electrical sub-panel) I have no choice but to build a cabinet with doors due to the insane amount of dust accumulation. (I am surrounded by Agricultural open acres of land all around me.) Sliding doors are the way to go b/c they don't eat up extra space required when you open them. I now am excited cuz this guy has taught me how!!!!! I can do this!!!! Thanks a million! I am off to buy my 1st router now!!!! Oh, anyone have recommendations on what I should be looking for in a router? Will the more expensive ones be worthwhile over the cheaper ones?
I’ve never built a cabinet with a sliding door before and just a weekend warrior in the shop. But with this video, I built a sliding door on my cabinet in just a few short hours. My wife is very pleased with the results! This video is awesome!!! Keep up the great work.
This was so fascinating to watch. I love your channel for all the in-depth explanations and illustrations/animations, but this time you even out-did yourselves! I do have one question/idea: Would it be a good idea (read: possible) to make a groove in the bottom tongue of the sliding door and add a wheel/bearing for better sliding? I was thinking you could drill a hole from the inside of the door towards the outside, and stopping before you go all the way through and using a dowel that holds this bearing in place? You would probably need a wider tongue, and thus a thicker door, but I don't see that as a dealbreaker necessarily. If that's doable, you would basically have invisible wheels, if I'm conceptualizing it correctly.
Fantastic video! I just got a commission for a cabinet that requires sliding doors for exactly the reason you mentioned: space limitations. Been puzzling out exactly how to do it and your tongue and groove explanation was exactly what I needed. Keep up the great work, Chris!
Warby parker is just for USA and CANADA only... anyway still your no.1 fan here in the philippines.. keep it upand goodbless... stay safe... more power to foureyes.
Hi guys I just wanted to say a big thank you for all your efforts. I watch several wood working channels but none of them reaches your level level of design. You style is simplistic but still modern with a bit of a twist. Your rocking chair belongs in a design museum as a piece of art. Maybe make a video about furniture build by your viewers inspired by your design style I used lot of your elements to build some bar chairs ...I got lots of complements for the design If you wish I share the CAD model if others want to build it Keep up the awesome job
Excellent video! Articulate, succinct, but all the necessary details. Thank you for not rambling on just to hear yourself talk as so many online videos do.
Even though I don't have plans to build something with sliding doors, watching helped my improve the way I think about approaching dimensions and fits. Thanks!
One more reason for Tongue groove which is similar to the benefit of distance between doors is distance to front face. Meaning for example if you want the door flush with face frame or slight inset, you need to do Tongue groove.Great video! Next one should be sliding without hardware but on drawers!
Thank you so much for this video. Built my first cabinet today and used your sliding door method to get results that were a lot better than I expected.
Thank you very much for this video. It is very helpful for me.. You make absolutely stunning furniture, so beautiful and sophisticated it is a pleasure to watch.
It feels nice when you add metric. Thanks. Also... I would love it if you threw in an oldschool-foureyes video every once in a while. I've been rewatching all the old stuff couse I miss it 😄 Some poetic/philosofic/pun-ic narrative and other-chris guitar track ❤
Excellent tutorial - thanks a whole lot, I really appreciate it and found it easy to understand. I was about to start planning construction of a credenza which will need sliding doors. This helped me settle some thoughts I had had, and convinced me not to go down the expensive sliding hardware route.
You always explain well how to do useful things. With sliding doors, I've found it useful to think about what happens if dirt gets in the groove. A hole at the end of the travel, through the bottom of the groove can be helpful.
Recently made a MCM console with sliding doors. Did the tongue and groove version and they worked well, but would do them differently next time. I would cut narrow slots in the case and cut rabbets on the backs of the doors, but not in the front. The rabbets in the front of the doors "show", you can look into the cracks under and over the doors and the must be neatly lined up. Also, both surfaces of the front rabbets must be finished nicely. It would be cleaner if the front of the doors were flat and the rabbets on the back help to close the gap between the doors.
Yes! I'm glad this was the top comment because I came on here just to say that what you explained is the way I do it, and it solves the problem of seeing any seam along the top of the door. It's also one less cut to do because you only have to do a rabbet on one side of the door.
Followed your suggestion and did 10mm wide from the face of the door at the bottom, but full width at the top because it was less work. Looks really clean. It's a tv cabinet, and only has doors on each end with an open shelf in the middle, so just one groove.
Great explanation one of the best in the topic, thanks Chris am ready to do my slide door without hardware which is awesome, the furniture that you use for the explanation looks beautiful, really nice design and with the sliding doors, wooow real nice thanks great content,
Thanks for the clear explanation! Very helpful 😊 Not sure if you'll see this, but I was wondering: 1) what's the ideal size for the tabs? 1/3 of the door's thickness? Half? 2) how much space would you leave minimum between the doors? 3) approx. how heavy could you make the doors without having to use hardware? Any advice would be greatly appreciated! 🙏
I love your videos. Your a great teacher and make it so easy for a beginner like me to follow along. I would love to be able to do a build with you and you teach me
Would you ever use a full width groove on the top and a tongue groove on the bottom? The benefit being you won't see any part of the tongue at the top.
Great video Chris, as always! Your timing for giving me a plethora of ideas about my own upcoming projects is uncanny! I have some sliding doors in mind for a shop cabinet project (now that plywood is coming down from the 'bank loan' level), but I was concerned about a dusty environment preventing smoothly-sliding doors over time, the upkeep needed to keep them cleaned out and/or waxed, etc. (and this would not involve hardwoods, just normal softer shop grade materials). I had thought about getting something hard and slick in the bottoms of the grooves, such as strips of melamine edging, but couldn't find an easy way to iron it on as groove bottoms. I eventually settled on making a laminated track assembly of alternating 1/4" strips cut from wood and from melamine board, so that the melamine surfaces end up as the groove bottoms. My project is mostly stacks of storage cabinet cubes built as towers, with these laminated track assemblies mounted on the front edges of the fixed shelves dividing and defining the cubes, so as to have the same two-sided track assembly serving the top of the lower cube and the bottom of the upper cube, with the melamine layers offset from the wood strips within the lamination, creating deeper grooves at the top of each door for easy door removal as yours do. My only hitch I've run into during test runs is cutting a melamine strip with smooth-enough edges (since a rough edge could bite into the sliding door bottom and defeat the purpose of using melamine in the first place). I've tried blue painter's tape and scratch cuts to clean up the edges on the melamine cuts, and the blade I'm using is admittedly not my best (since I didn't want to wear out a good one on several dozen 3 foot melamine cuts, the stuff being so hard and brittle). So I was thinking of coming down off my cheap high horse and springing for a new blade to cut the melamine. And what do you know! Just as I'm re-thinking using this material at all in this application, along comes Chris Salomone with some very interesting thoughts on groove construction! I'm still not sure which way I'll ultimately go, as I have by now been pretty thoroughly bitten by the shop-made laminated track bug. By the way, if you've read this far, I'd be very interested in your thoughts about making and then installing a separate track? Cutting upper and lower grooves in the same divider piece won't really work for me, unless I beef up the edge of the plywood or something. And it's totally fine if time prevents a reply. It's truly a master class video on the topic! Cheers!
@@ugosmith7529 It does help somewhat. That was the 'scratch cut' I mentioned. Raise the blade just an 1/8" or less proud of the table saw surface and run the melamine over that. Then flip the melamine front to back, keeping the same edge against the rip fence but now the melamine is on top, raise the blade to just higher than the melamine thickness, and run it through again. Does a decent job, but still some flaking. And it could be that the melamine I'm cutting is too old, having been in a garage for a number of years, so it may be brittle and dried out (if that plastic layer does dry out). But I also suspect my blade. Maybe a bit of sanding will help the flaky edges enough to still let it be a decent groove bottom. Oh, my project got side-tracked due to lumber pricing, but still on the radar. So I have yet to start it, instead doing some other smaller tasks. Thanks for the suggestion!
@@billparrish4385 yeah, the lumber prices have put a damper on my shop projects also. Thanks for responding and following-up, if the technique you described doesn't work still, I'mnot sure what else could help, you may indeed have to pony up for a specialized blade.
appreciate so much 1/16 of a in inch = 2mm on the screen! :) It is hard to describe (probably both ways) but when you are used to metric, it's is really not ez to visualize quickly when fractions of inches are discussed.
Question: Do you ever build a sliding door with a raised bottom "ridge" on the bottom horizontal shelf, made of wood or aluminium ? Not only does it remove the need to cut a groove in the bottom horizontal shelf, but the slot cannot get filled with junk and cause the sliding section to either bind or jam completely. The same principle has been used on the bottom of sliding wardrobe doors for years.
Why so amazing dude? This vid is sooo good and well explained and all that I can't help but be aggressively amazed, haha (I'm planning to make a closet 130x140~ for a small room, and I needed much much this info for my planning! Thanks)
Hi Chris, love your videos and the clarity of your explanations. I’m not from the US though so I’m not familiar with the Imperial system, could you please include Metric measurements too?
@@KingKarrit From your reponds you're clearly not familair with the metric system. There are currently only 3 countries left in the world that have not moved to metric namely; Liberia, Myanmar and the US. Even the "Empire" which brought the Imprerial system to the US, have move to the 21 century. th-cam.com/video/hid7EJkwDNk/w-d-xo.htmlsi=4yL7bcSILLqx7vdo
Nice video. I have a big cabinet job with quite a few sliders like this, yet it's painted. Wondering about sticking paint and wear on the sliding area. But a nice option if I don't find any hardware.
I like to use a pair of small bearings instead of a bottom tongue. Cut a mortice near each edge, then drill a blind hole from the inside and use a dowel as an axle
super awesome video! thanks so much for your sliding panel door insight. One question that I had after watching, Im one of those without a table saw, but I ido have my trusty Festool Of1400 Router. I can see making the Grooves, but would have loved to see you making some tongue cuts on the door panels with a router to see how you would go about it. Any tips for cutting the tongue from the doors using a plunge router?
Right on time! Was just about to start on a sliding door cabinet. I’m using heavy 3/4 material for the doors and worried about weight and friction. Was considering gluing a t slot into the top groove and hanging the door from it. Thoughts anyone?
![Cabinetry Basics Part 1 [video 435]](http://i.ytimg.com/vi/3N_T-YpkBCg/mqdefault.jpg)
So glad I grew up in a country with the metric system.
and im glad my parents did
When you grow up with feet and inches, it just makes sense. You can be just as precise with Imperial as you can with Metric. Maybe the math is a little easier with metric, but that's why we have calculators.
I find the math of imperial to be easy once I became an experienced woodworker. Example (quick math in your head): 1167mm+886mm= VS 18 1/8 + 56 7/16=…….. imperial is quicker in an instance like this. I do really like metric though and if one system were only to survive it probably has a wider range of applications and ease
Fractions make more sense from ahuman perspective.
Using the metric system is universal. For example, some Americans use the metric system instead of feet and inches. Educate yourself.
Upon unboxing, I was immediately upset at how the rails were very noticeably bent. But I kept going, all tools needed to assemble were included th-cam.com/users/postUgkxqtX4Dxs6aecAZEuz6GY5-d81YecKCshn and I had it set up in about 30 minutes. Honestly I love this thing, make sure to read the measurements and measure your space so you know if it'll work for you. I bought this to put inside my closet, underneath where I hang my clothes and it is absolutely perfect! It is VERY sturdy and all drawers glide easily and mine are stuffed, and they are still flush when closed.
This is the kind of information the people need! Thanks, Chris!
Probably one of the best explanations on how to properly build sliding doors I've come across... even if you don't make fine furniture and only shop cabinets. Great presentation and video production.
Chris, I think you read my mind. Every time I have an idea, you drop a video on the exact topic I'm looking to learn more about. I've built two of your designs now, and always feel confident following your instruction. Thanks for everything you do.
Thanks man...appreciate it. Glad you're enjoying the videos gaining something from them :)
I just built my first sliding door cabinet and your tips helped a lot, 80 x 36 x 13 inches deep. I aimed for 3/4 overhang just like you recommended. The sliding doors are 40 x 33 and I used half inch and there bowed but it’s a shop cabinet and it’s practice for the real furniture I’ll build for the house. My shop is 1.8 metres wide by 4.8 meters long, super small shop in Dublin, Ireland 🇮🇪
I don't own a table saw nor router, but I am subbing right now! Why? This guy is so down to Earth. He doesn't skip or race through project. I recently bot 2 Bluetti AC300s & 2 B300s. I can't find a cart, rack or cabinet that will properly fit my power station. Because I live in rural America & keeping my Power Station in my outdoor kitchen (once I install a Transfer Switch (electrical sub-panel) I have no choice but to build a cabinet with doors due to the insane amount of dust accumulation. (I am surrounded by Agricultural open acres of land all around me.) Sliding doors are the way to go b/c they don't eat up extra space required when you open them. I now am excited cuz this guy has taught me how!!!!! I can do this!!!!
Thanks a million! I am off to buy my 1st router now!!!!
Oh, anyone have recommendations on what I should be looking for in a router? Will the more expensive ones be worthwhile over the cheaper ones?
I’ve never built a cabinet with a sliding door before and just a weekend warrior in the shop. But with this video, I built a sliding door on my cabinet in just a few short hours. My wife is very pleased with the results!
This video is awesome!!! Keep up the great work.
This was so fascinating to watch. I love your channel for all the in-depth explanations and illustrations/animations, but this time you even out-did yourselves! I do have one question/idea: Would it be a good idea (read: possible) to make a groove in the bottom tongue of the sliding door and add a wheel/bearing for better sliding? I was thinking you could drill a hole from the inside of the door towards the outside, and stopping before you go all the way through and using a dowel that holds this bearing in place? You would probably need a wider tongue, and thus a thicker door, but I don't see that as a dealbreaker necessarily.
If that's doable, you would basically have invisible wheels, if I'm conceptualizing it correctly.
I taught for 38 years. You have a gift.
This was incredibly helpful. I just did sliding doors and your tutorial was all I needed. Thank you!
Fantastic video! I just got a commission for a cabinet that requires sliding doors for exactly the reason you mentioned: space limitations. Been puzzling out exactly how to do it and your tongue and groove explanation was exactly what I needed. Keep up the great work, Chris!
Perfect timing! Wanted to embark on a console build with sliding doors soon!
Nice. Hope this helps
Me too :-)
I very much appreciate your thorough descriptions and reasoning for the choices that you make. Of course, your delivery is great as well, thank you.
Great explanation for using this technique, Chris~! I've actually been looking for something like this, so your timing is great.
Thanks much~!
In term quality, this is awesome. Excellent accessible instructional video. This is why I’m a proud Patreon supporter. Bravo!
Warby parker is just for USA and CANADA only... anyway still your no.1 fan here in the philippines.. keep it upand goodbless... stay safe... more power to foureyes.
Thank you for providing the video and the millimeter version; they are incredibly helpful for those of us imperially impaired.
This video was awesome! I really appreciate how you broke down the math is this. :)
Thanks...glad you found it helpful :)
Hi guys I just wanted to say a big thank you for all your efforts.
I watch several wood working channels but none of them reaches your level level of design.
You style is simplistic but still modern with a bit of a twist.
Your rocking chair belongs in a design museum as a piece of art.
Maybe make a video about furniture build by your viewers inspired by your design style
I used lot of your elements to build some bar chairs ...I got lots of complements for the design
If you wish I share the CAD model if others want to build it
Keep up the awesome job
Thanks Bernd. Appreciate the kind words...we always love seeing things people build.
@@Foureyes.Furniture where should I email some pictures and the drawings?
Excellent video! Articulate, succinct, but all the necessary details. Thank you for not rambling on just to hear yourself talk as so many online videos do.
Nice clean lined work.
Thoughtfully produced, quietly explained videos.
No hype.
Great work ,well done.
Out of the sunglasses I prefer the Barkley or Downing, for you face I think the Barkley ones look the best. Great video man, thanks for all the tips!
Even though I don't have plans to build something with sliding doors, watching helped my improve the way I think about approaching dimensions and fits. Thanks!
That is great. Appreciate it.
One more reason for Tongue groove which is similar to the benefit of distance between doors is distance to front face. Meaning for example if you want the door flush with face frame or slight inset, you need to do Tongue groove.Great video! Next one should be sliding without hardware but on drawers!
Not a bad idea. Maybe we'll do that.
I love these kind of videos, and you do a great job of explaining each step. Thank you for the content!
Thank you so much for this video. Built my first cabinet today and used your sliding door method to get results that were a lot better than I expected.
Great job explaining.. and not getting to technical..as a newbie wood worker this was a great video to help me out with some questions..
Thank you very much for this video. It is very helpful for me.. You make absolutely stunning furniture, so beautiful and sophisticated it is a pleasure to watch.
Thanks Master...I learnt a lot of this originally Japanese technique... No hardware at all!!!... Greetings from Medellin!!!
Hello, I am from Cambodia, I really love your work and your video.🇰🇭❤
Aloha cambodia
I remember doing this for our wood work classes back in high school . From Malaysia
It feels nice when you add metric. Thanks. Also... I would love it if you threw in an oldschool-foureyes video every once in a while. I've been rewatching all the old stuff couse I miss it 😄
Some poetic/philosofic/pun-ic narrative and other-chris guitar track ❤
I love these in depth videos. What an amazing groove you have 😉
Very informative! Need to let this digest then come back and re-watch a few times!
You have changed my mind about sliding doors. Beautiful work. I'm going to incorporate more of these into my work. Thank you!
Exceptional content, animations, explanations-you saved me hours of trial and error.
Excellent tutorial - thanks a whole lot, I really appreciate it and found it easy to understand. I was about to start planning construction of a credenza which will need sliding doors. This helped me settle some thoughts I had had, and convinced me not to go down the expensive sliding hardware route.
You fans all the way here in Jamaica blood, loving the content, very useful.
Thanks Romario :)
Trinidad and Tobago here!
Learned alot!
It is quite remarkable that you can talk more then 12 minutes about something simpele as This, well done 😁
Impressed. Thanks a lot. Learned so much in less than half an hour.
Thanks Chris! I made sliding doors today and I wish I would have seen the video before :)
My favourite how to of yours yet. Great video.
Great explanation! Thanks for taking the time to make this.
Love the details and instructions. Thank you so much for the video!
Great film and instruction video. I’m going to try it on my next project!
You always explain well how to do useful things. With sliding doors, I've found it useful to think about what happens if dirt gets in the groove. A hole at the end of the travel, through the bottom of the groove can be helpful.
Good call. I've never though about that before. I suppose I would probably go for a vacuum if I ever faced that :)
@@Foureyes.Furniture I guess the ones where I found it needed were in a preschool. Under less challenging circumstances it's less important.
Recently made a MCM console with sliding doors. Did the tongue and groove version and they worked well, but would do them differently next time. I would cut narrow slots in the case and cut rabbets on the backs of the doors, but not in the front. The rabbets in the front of the doors "show", you can look into the cracks under and over the doors and the must be neatly lined up. Also, both surfaces of the front rabbets must be finished nicely. It would be cleaner if the front of the doors were flat and the rabbets on the back help to close the gap between the doors.
Yes! I'm glad this was the top comment because I came on here just to say that what you explained is the way I do it, and it solves the problem of seeing any seam along the top of the door. It's also one less cut to do because you only have to do a rabbet on one side of the door.
Followed your suggestion and did 10mm wide from the face of the door at the bottom, but full width at the top because it was less work. Looks really clean. It's a tv cabinet, and only has doors on each end with an open shelf in the middle, so just one groove.
Great explanation one of the best in the topic, thanks Chris am ready to do my slide door without hardware which is awesome, the furniture that you use for the explanation looks beautiful, really nice design and with the sliding doors, wooow real nice thanks great content,
Thanks for the clear explanation! Very helpful 😊
Not sure if you'll see this, but I was wondering:
1) what's the ideal size for the tabs? 1/3 of the door's thickness? Half?
2) how much space would you leave minimum between the doors?
3) approx. how heavy could you make the doors without having to use hardware?
Any advice would be greatly appreciated! 🙏
Dam you're good at making instructional videos - this is just what I'm looking for thank-you.
Thank you. I never think of doing doors this way.
Excellent video. Great graphics. These tips really helped with my full size shoji doors.
Your videos are the BEST! I’m learning so much. I plan to buy some of your plans as well. Thank you!
Thank you so much...they''ll be there for you when you're ready :)
Perfect technical video - great job! 👍
I appreciate you putting in MM, Thankyou awesome video as always. Thanks Chris
I love your videos. Your a great teacher and make it so easy for a beginner like me to follow along. I would love to be able to do a build with you and you teach me
Excellent video!!! Thank you so much for all the valuable information.
IDK!!! Maybe I Will Have To Try!!! I Am About 8-9 Months In. So Still Pretty New!!! Thank You!!! 🤔🤷♂️👍🤦♂️😎
Such sweet explanation- thank you!
Thank you for the detailed explanation.
Would you ever use a full width groove on the top and a tongue groove on the bottom? The benefit being you won't see any part of the tongue at the top.
Glad I read the comments before asking about the visible top tongue. Sounds like a good solution.
Thank you for the helpful video, please keep up the excellent work and explanation on the details of the video. Love your woodworks SKILLS
Thanks for the tips and the graphics 🙏👍
Thank you for this, very thorough and informative!
Perfect! My next project will hopefully include sliding doors. This was helpful
Sweet. It's a pretty easy feature :)
Great video Chris, as always! Your timing for giving me a plethora of ideas about my own upcoming projects is uncanny! I have some sliding doors in mind for a shop cabinet project (now that plywood is coming down from the 'bank loan' level), but I was concerned about a dusty environment preventing smoothly-sliding doors over time, the upkeep needed to keep them cleaned out and/or waxed, etc. (and this would not involve hardwoods, just normal softer shop grade materials). I had thought about getting something hard and slick in the bottoms of the grooves, such as strips of melamine edging, but couldn't find an easy way to iron it on as groove bottoms.
I eventually settled on making a laminated track assembly of alternating 1/4" strips cut from wood and from melamine board, so that the melamine surfaces end up as the groove bottoms. My project is mostly stacks of storage cabinet cubes built as towers, with these laminated track assemblies mounted on the front edges of the fixed shelves dividing and defining the cubes, so as to have the same two-sided track assembly serving the top of the lower cube and the bottom of the upper cube, with the melamine layers offset from the wood strips within the lamination, creating deeper grooves at the top of each door for easy door removal as yours do.
My only hitch I've run into during test runs is cutting a melamine strip with smooth-enough edges (since a rough edge could bite into the sliding door bottom and defeat the purpose of using melamine in the first place). I've tried blue painter's tape and scratch cuts to clean up the edges on the melamine cuts, and the blade I'm using is admittedly not my best (since I didn't want to wear out a good one on several dozen 3 foot melamine cuts, the stuff being so hard and brittle). So I was thinking of coming down off my cheap high horse and springing for a new blade to cut the melamine.
And what do you know! Just as I'm re-thinking using this material at all in this application, along comes Chris Salomone with some very interesting thoughts on groove construction! I'm still not sure which way I'll ultimately go, as I have by now been pretty thoroughly bitten by the shop-made laminated track bug.
By the way, if you've read this far, I'd be very interested in your thoughts about making and then installing a separate track? Cutting upper and lower grooves in the same divider piece won't really work for me, unless I beef up the edge of the plywood or something. And it's totally fine if time prevents a reply. It's truly a master class video on the topic! Cheers!
A bit late but couldn't scoring the melamine help getting a cleaner cut
@@ugosmith7529 It does help somewhat. That was the 'scratch cut' I mentioned. Raise the blade just an 1/8" or less proud of the table saw surface and run the melamine over that. Then flip the melamine front to back, keeping the same edge against the rip fence but now the melamine is on top, raise the blade to just higher than the melamine thickness, and run it through again. Does a decent job, but still some flaking. And it could be that the melamine I'm cutting is too old, having been in a garage for a number of years, so it may be brittle and dried out (if that plastic layer does dry out). But I also suspect my blade. Maybe a bit of sanding will help the flaky edges enough to still let it be a decent groove bottom. Oh, my project got side-tracked due to lumber pricing, but still on the radar. So I have yet to start it, instead doing some other smaller tasks. Thanks for the suggestion!
@@billparrish4385 yeah, the lumber prices have put a damper on my shop projects also.
Thanks for responding and following-up, if the technique you described doesn't work still, I'mnot sure what else could help, you may indeed have to pony up for a specialized blade.
I slid over and clicked that like button !!
i think i´ve told in other videos, I Love you! you are a genius!!
Love this style of video! So much value!
appreciate so much 1/16 of a in inch = 2mm on the screen! :) It is hard to describe (probably both ways) but when you are used to metric, it's is really not ez to visualize quickly when fractions of inches are discussed.
Great way of explaining this. Thanks. Subscribed!
thank you for a great learning video and for using mm as well
I enjoyed that. It's was interesting to hear what you say and what sizes you recommend. Great work Chris 👍
Great video. 14:52 Looking forward to more plans in your plans section.
Question: Do you ever build a sliding door with a raised bottom "ridge" on the bottom horizontal shelf, made of wood or aluminium ?
Not only does it remove the need to cut a groove in the bottom horizontal shelf, but the slot cannot get filled with junk and cause the sliding section to either bind or jam completely.
The same principle has been used on the bottom of sliding wardrobe doors for years.
Why so amazing dude? This vid is sooo good and well explained and all that I can't help but be aggressively amazed, haha (I'm planning to make a closet 130x140~ for a small room, and I needed much much this info for my planning! Thanks)
Brilliant video, great how to explained yourself in several ways 👌🏻
Love your work and ideas, I wish I could build a workshop like yours. That's awesome.
Your videos are so ridiculously informative. So I mean this honestly, “thank you”. Also, The Barkley’s look great. Cheers!
Love these informative videos and your content in general! Keep up the good work
This is great, man. Thanks so much.
Great info, Chris.
Bill
- Awesome video & info. Thanx 4 sharing.
Excellent timing, working on no hardware sliding doors as we speak!
you are such a good explainer. thx a lot !
Ideal for galley kitchens!
Great video ! Much appreciated.
who knew collecting action figures would steer me into learning this stuff.
wild
Gracias por el Video Chris, invaluables consejos.
This is such a great video!
Great video, and beautifull work man!
Great video! As far as the sunglasses, I liked the Harris ones for you 😀
Appreciate that. I'll keep gathering feedback and then make my pick :)
Great video Chris!
great video! exactly what I needed, thanks man!
Hi Chris, love your videos and the clarity of your explanations. I’m not from the US though so I’m not familiar with the Imperial system, could you please include Metric measurements too?
If you're a carpenter you should learn imperial anyway. Fractions are quicker and easier.
@@KingKarrit From your reponds you're clearly not familair with the metric system. There are currently only 3 countries left in the world that have not moved to metric namely; Liberia, Myanmar and the US. Even the "Empire" which brought the Imprerial system to the US, have move to the 21 century. th-cam.com/video/hid7EJkwDNk/w-d-xo.htmlsi=4yL7bcSILLqx7vdo
Nice video. I have a big cabinet job with quite a few sliders like this, yet it's painted. Wondering about sticking paint and wear on the sliding area. But a nice option if I don't find any hardware.
I like to use a pair of small bearings instead of a bottom tongue. Cut a mortice near each edge, then drill a blind hole from the inside and use a dowel as an axle
super awesome video! thanks so much for your sliding panel door insight. One question that I had after watching, Im one of those without a table saw, but I ido have my trusty Festool Of1400 Router. I can see making the Grooves, but would have loved to see you making some tongue cuts on the door panels with a router to see how you would go about it. Any tips for cutting the tongue from the doors using a plunge router?
Right on time! Was just about to start on a sliding door cabinet. I’m using heavy 3/4 material for the doors and worried about weight and friction. Was considering gluing a t slot into the top groove and hanging the door from it. Thoughts anyone?
Good info and good animations, thanks fellas.
Thanks :)
Which software did you use on graphics, this is great