This applies to almost any year accord it looks like. I popped off my 91 hub thanks to your video! Thought it was a much bigger pain until I watched this.
Привет приятель. Это отличное видео! Все очень доступно объяснил и показал. Также стоит использовать немного медной смазки, по краям центрального колпачка, а также на посадочном месте для колеса на тормозном диске, чтобы колесный диск не прикипал и не пришлось стучать по нему ногой.)) Медная смазка не боится больших температур. Ты крутой механик, удачи тебе!))
Really good video, great detail and thanks for not kicking out from under the car 😅. I just need to see if this applies the same way when the car has drum brakes?
The screws do nothing really for us. More for the factory when they are building the car. It lightly secures the rotor while it's travelling down the line.
I swear to God. The detail that u provide is gold! A lot of people just install and skip steps etc.. U answered every question I had.
This applies to almost any year accord it looks like. I popped off my 91 hub thanks to your video! Thought it was a much bigger pain until I watched this.
Great video Brother - I've done both rear hub/bearings on my 04 accord while referencing this video. Well done!
You make great tutorial videos! Thank you! Al in Portland, Oregon
This is one of the most detailed videos I've seen. Thanks 😊
Thank you for uploading this video.
Привет приятель. Это отличное видео! Все очень доступно объяснил и показал. Также стоит использовать немного медной смазки, по краям центрального колпачка, а также на посадочном месте для колеса на тормозном диске, чтобы колесный диск не прикипал и не пришлось стучать по нему ногой.)) Медная смазка не боится больших температур. Ты крутой механик, удачи тебе!))
I can't thank you enough for sharing this knowledge. GOD BLESS YOU.
Nice video, a big help to tackle this repair - thanks.
Greatly appreciated! The small details were very helpful to avoid damaging parts.
Love the videos, would love to see a diagnose / repair of the F150 door ajar issue.
Very thorough. Thank you!!
Clean it before removing the dust cap. Great vid
Really good video, great detail and thanks for not kicking out from under the car 😅. I just need to see if this applies the same way when the car has drum brakes?
We would be friends lol!! Great personality man. Thanks for the awesome video!!
Very good thank you for this helpful video
Good video, well produced 👌
Thank you, I appreciate it. Glad you liked the video.
Thanks man, helped me out.
598
32 mm for the wheel bearing?
Yes, just did it myself yesterday
Great video champ
Thank you bro.😊👍
Good video, nice! 👍🏻
Merci ça M a beaucoup aidé
Doit-on changer les deux roues arriere
I swear this dude was on a dig in Egypt
Dust flying everywhere
Very well done
Nice job
Hi good video. Nice and to the point. Quick question : Any grease to use ...? For example the part the new bearing slides onto?
pretty sure there needs to be friction there. the bearing has a sleeve that sits on the spindle. the sleeve is what he had to crack to get off
Great job on vido. Only thing I do different is that I bush the caluaber before I take caluaber off.
Thank you
👌👌👌
Is there any other way to get the race off other than using the cutting tool?
I put a thin screwdriver behind it and worked it top, bottom, left, right and eventually got it far enough out I could slide it off.
@@shaynekraczek3999 thanks haha I left this comment just over 1 year ago 😂. The race popped right off and luckily wasn’t stuck for ke
Haha oh good. Glad you're not still driving around with a busted wheel bearing 😂
Would a bad wheel bearing cause a tsc light on?
Thanks!!!!
Are the new bearings sealed with grease then ?
good job
Do you have to take off the inner race or why do I need to remove can someone help me doing this today and dident quiet understand that part
thanks
Dope
The stake on mine is too tight to get any punch into it… what should I do?
my local garage wants $500 each to change them, must be the flat rate price
Cant-cha change just the bearing & use d old hub like i did on d front?
Why was there no screws? Is that okay to not have screws in it?
The screws do nothing really for us. More for the factory when they are building the car. It lightly secures the rotor while it's travelling down the line.
Sup homie?!
Got a drill just like that one
Niiiice 🫡
Nice when you have all the tools😅
Funny how you just said "if you start with air the. Finish with air...." but then you sprayed brake cleaner
Socket size please
32mm
Your breathing in asbesdos dust stop blowing air on that brake area.
Too much talking.