Super fun! Feature Request. It would be nice if there was a way to hover over a patch cord, press a ctrl key and do a quick visualization the signal coming through. Very handy not to have to manually add scopes, level meters or spectrum analyzers manually. Anyway, again, nice video.
Thanks much~ And selecting any module shows scopes for its connected in ports (including pre-cords) and all outgoing signals in the Inspector Panel. It isn't everything you asked for but worth noting.
Bravo! Another neat tutorial, getting us to hear differently. Enjoyed the references to Bob Ross and Spiderman… ;-) The pacing is quite nice in that the end result flows pretty well from what precedes it without being completely predictable. The connection to MPE or PolyAT can help people move to the expressive side. People often misunderstand what it means, saying that “I could do the same thing with knobs”. Not only is this inaccurate but the same people typically don’t do much with expressiveness. So many patches (including many BWS ones) aren’t even support velocity-sensitive. Yet a great BW strength is in supporting MPE and other forms of expression. In many cases, PolyAT is enough to make a huge difference. Yet rare is the patch which supports it out of the box. With inexpensive devices like Novation’s Launchpad X and ROLI’s LUMI, patches supporting PolyAT don’t require a CS-80 level of commitment.
Feature request! A small chicklet module that just does the feedback job of the long delay at lowest setting. It just seems janky to have to use a big delay module to do feedback routings. Additional Feature request! A device line device that does the same feedback process sending signal back to another point in the device line. Or an option on the audio routing device to allow fedback signals with the required .02ms or however many samples/blocks delay.
Great video! Are we ever getting feedback outside of the grid and fx containers (say through the audio receive module)? It's something a lot of us are wishing for. Thanks anyways! 😄
f* finally, I was bagging for a feedback possibility for years until I gave up on it. I hope you can also feedback a send channel. But I still doubt that.
Can I use FX Grid and long delay inside it to make feeback connection for a chain of plugins? Right now I use RME's loopback feature to do this, for basic tape loop degradation.
Four years later and the grid still can't do 1 sample unit feedback for buiding phasers , karplus strong , filters etc .. Since the grid uses feedback that depends on the smallest audio buffers size , the feedback loop will always be filled with harmonic content defined by the buffer size , whcih is not what you want when you want to build stuff . SUch a shame they never implemented it , .. Another case that the grid is not as capable as reaktor or max msp . If they added some FFT , IIFT modules you could build your own spectral modules , but NO .. now they are charging money for spectral modules . Bitwig is a joke
>>> Propaganda destroys greedy people. The program is anachronistic, old DOS style. It is very heavy on quad-core processors. It does not use the super fast memory of graphics cards. Prices from space. This means that the company has a small manager. I do not recommend this program to musicians ! I recommend clear thinking ! Greetings from Poland
![Modular Concepts: Synthesis World Tour feat. Polymer [Bitwig Studio]](http://i.ytimg.com/vi/SZd7aoOjnCE/mqdefault.jpg)
![Modular Concepts: Synthesis World Tour feat. Polymer [Bitwig Studio]](/img/tr.png)
![Let's Build a... Repeater [Bitwig Studio]](http://i.ytimg.com/vi/XKKYi0TSGiQ/mqdefault.jpg)
![Modular Concepts: Polyphony [Bitwig Studio]](http://i.ytimg.com/vi/918bVhni7xU/mqdefault.jpg)
I love the humor that is thrown in here and there
Feedback loops is awesome whil love the abelity like IN ableton to route feedback sounds into the same Channel or bus
Super fun!
Feature Request. It would be nice if there was a way to hover over a patch cord, press a ctrl key and do a quick visualization the signal coming through. Very handy not to have to manually add scopes, level meters or spectrum analyzers manually. Anyway, again, nice video.
Thanks much~ And selecting any module shows scopes for its connected in ports (including pre-cords) and all outgoing signals in the Inspector Panel. It isn't everything you asked for but worth noting.
@@davelinnenbank750 seriously, wow that's great 👍 👏 😄
Thank You for amazing Daw, for fresh ideas!
Bravo! Another neat tutorial, getting us to hear differently.
Enjoyed the references to Bob Ross and Spiderman… ;-)
The pacing is quite nice in that the end result flows pretty well from what precedes it without being completely predictable.
The connection to MPE or PolyAT can help people move to the expressive side. People often misunderstand what it means, saying that “I could do the same thing with knobs”. Not only is this inaccurate but the same people typically don’t do much with expressiveness. So many patches (including many BWS ones) aren’t even support velocity-sensitive. Yet a great BW strength is in supporting MPE and other forms of expression.
In many cases, PolyAT is enough to make a huge difference. Yet rare is the patch which supports it out of the box. With inexpensive devices like Novation’s Launchpad X and ROLI’s LUMI, patches supporting PolyAT don’t require a CS-80 level of commitment.
Feature request! A small chicklet module that just does the feedback job of the long delay at lowest setting. It just seems janky to have to use a big delay module to do feedback routings.
Additional Feature request! A device line device that does the same feedback process sending signal back to another point in the device line. Or an option on the audio routing device to allow fedback signals with the required .02ms or however many samples/blocks delay.
I was thinking the same thing.
This series is awesome, more please!
Great video! Are we ever getting feedback outside of the grid and fx containers (say through the audio receive module)? It's something a lot of us are wishing for. Thanks anyways! 😄
This is awesome - thank you! Been trying to explore timbres I get from my Nonlinear-Labs C15 in the Grid, and this is.a great first step.
very nice, thank you for that amazing daw. Its such a intuitive and creative toolbox. Please never change the way you go!
"Not sure I meant to make windshield wipers, but here we are!"
Great work guys and great video Dave!
Sweeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeet! Always inspirational, man! Thank you!
:)
f* finally, I was bagging for a feedback possibility for years until I gave up on it. I hope you can also feedback a send channel. But I still doubt that.
Can I use FX Grid and long delay inside it to make feeback connection for a chain of plugins? Right now I use RME's loopback feature to do this, for basic tape loop degradation.
MY COMPUTER BLEW UP
First here
Four years later and the grid still can't do 1 sample unit feedback for buiding phasers , karplus strong , filters etc ..
Since the grid uses feedback that depends on the smallest audio buffers size , the feedback loop will always be filled with harmonic content defined by the buffer size , whcih is not what you want when you want to build stuff .
SUch a shame they never implemented it , ..
Another case that the grid is not as capable as reaktor or max msp .
If they added some FFT , IIFT modules you could build your own spectral modules , but NO .. now they are charging money for spectral modules .
Bitwig is a joke
>>> Propaganda destroys greedy people. The program is anachronistic, old DOS style. It is very
heavy on quad-core processors. It does not use the super fast memory of graphics cards. Prices from
space. This means that the company has a small manager. I do not recommend this program to
musicians ! I recommend clear thinking ! Greetings from Poland
😂