D&E PERFORMANCE MSD LS 6014 BOX TUTORIAL#1
ฝัง
- เผยแพร่เมื่อ 7 ก.ค. 2024
- MSD view for the 6014 box tutorial on basic usage of MSD view software TUTORIAL#1
Any comments questions or even how to improve on these videos do not hesitate to leave comments Thank you for watching
Please like or subscribe 👍
dandeperformance.com
If you are interested in the purchase of MSD 6014 LS box click on the link below thanks for watching
www.amazon.com/gp/product/B01...
Interested check out ebay items below..
www.ebay.com/itm/285075231017...
www.ebay.com/itm/285075135323...
www.ebay.com/itm/285044922083... - ยานยนต์และพาหนะ
![[FULL EP.14] เซียนหรั่ง สอน มาร์ชจุ จับปูนา ฮากระจาย | เฮ็ดอย่างเซียนหรั่ง | One Playground](http://i.ytimg.com/vi/M8mPjd_T2lo/mqdefault.jpg)
Dude this video was so helpful. Thank you
YES! Finally a carb guy!
I did a carbureted LS3 ‘78 T-Top Regal. It’s bad to the bone bro
Edelbrock makes the intake with MSD mount. Not Holley
So u can't use the MAP sensor unless u are doing custom tune right?
Hi there sir have a 48 LS engine where is a carburetor I put the MSD 6414 on it started it up but if I give it gas it backfires and won't take gas it's a nightmare can't find nobody to help me I am so frustrated I spent $3,000 and it won't run right I just backfired when i gave it gas i thank i got a dad MSd i ofder another one
Hi 65 yr old LS rookie here. I have a new built 2004 LS 6.0,30 over,aggressive cam for torque (airboat application, need torque to get boat moving with 4-6 people) LS1 heads, 750 single pump but dual feed carb,(heavy valve springs ) hire rise intake with another 2 inch spacer to bring in more air, new 6014 msd box. Looking for a video to teach me how to install, how to use laptop, what software i need and how to use it. And what those settings on the MSD box work/effct the engine. Any help greatly appreciated. Tim, Omaha Nebraska
What is the standard rev limiter as the box comes? Using the truck HO tune currently
6700 is the default
Can you explain map timing
Did you hook yours up straight, like red to 12v and black to ground? Or did you use a relay
I hook mine straight to key switch 12v use a 30 amp inline fuse for added safety
ground straight to the chassis or a good ground source..
I'm getting 10 volts to my 5 volt reference, thinking my box is bad? Pink wire has 10 volts-black wire has 0 volts- cam and crank have 12.6 volts. Anyone had this problem?
I just LS swapped my 78 K5 Blazer. Has a stage 3 cam. Running natural carbureted. So when I first start it, I should have the MSD set to Custom? Then later I can see where it is idling at and adjust the dots till it runs how I want?
open MSD view go to file it should say 6014 sample if you do not have a current file saved click on that open MSD view go to your timing table click on custom1
And then you can set your timing at idle with your dots
I usually give it at 400 RPM right around 11° or 12° of timing at that first initial fire off
Find out where it likes to idle and then adjust the dots in that idle point
Make sure you go to settings and set all your max rev
launch rev
coil type
idle timing control
first before changing your initial timing table if you do not set this it will always default make sure after every change you go up to file and hit save
After each change make sure you transfer the file to the MSD
So you will go to transfer and then send usually takes a few moments for your adjustments to be loaded into the MSD do not turn off the key as you are transferring a file
Hi is grounding the MSD box to the cylinder head ok.
Or should it be the frame?
Follow the instructions to the t on all wiring
I'm pretty sure the instructions say to ground the harness to the back of the heads or the block
@@deperformance9741 Thanks
Can you tune mines
How do you mess with idle timing because if my cam doesnt chop enough i want to make it chop more
Having a choppy cam has to do more with your cam timing and not idle
@@deperformance9741 Just lower the idle
Where do you get the software and how do you load it into the box? Just bought a truck with one of these mds box’s
USB cable with the old style GoPro end
unless it is the older 6010 box takes that really old serial Port cable
You might have to check Holly's website for the software just go under support and type in 6014 MSD box Holly acquired MSD some years ago
If that doesn't work try calling their support directly and see if you can get one of their USB drives with the software on it
@@flipit7854 it is a msd Ls series 6014
"Im not going to get into fine tuning" - see ya!
Im new to ls swaps how does the wiring goes because i dnt know how to wire up the box
Carlos Quintero
It's very easy and straightforward the Box comes with two separate harnesses one for the 58 reluctor and the other ones for the 24 reluctor just need to determine what your LS is.. all the plugins are going to fit in their spot not 2 plugins are alike.. I could possibly make a short video on this the turbo videos going to be coming out in the next week and a half or so maybe I'll throw and wiring harness video..
Dave A thanks I appreciated if you make a video on wiring
do one harnes at a time theres one for the coils and one cranck and cam the ground the motor and msd box
msd has a instruction digram online
THE WAY TO UPGRADE A MSD BOX IS REPLACE IT WITH A Daytona Sensors Smart Spark
That is your opinion
I have had good luck in the past with MSD products MSD is now owned by Holley my opinion being Holley makes some good products. The only downfall is the 2.5 bar map sensor on the 6014
6010 can scale to 3 bar but that box is discontinued
Not saying that Daytona sensors box is any better or any worse
I haven't had the opportunity to own one of these Daytona sensors boxes maybe in the future I can do a comparison with screen capture..
I think both products are good depending on what you want to use them for and what your goals are with your LS carb project.
.
@@deperformance9741 Didn't know Holley bought them should be a +. Check out the NIGHTWRENCHERS channel, he just did an unboxing ved with more to come. That opinion of mine wasn't dreamed up it was formed.Take a good long look through the D.S. web-page.
@@billytarpon9871 Not at all a Good thing with Holley buying MSD, The MSD coils and most other MSD products as well as Holley products are now outsourced and Made in China garbage, The 6014 Box says Made in Texas still, But the LS coils as well as others that MSD offers now are known for burning up or even D.O.A., Made in China garbage with same High $ price, Stick to LS3 '190' GM coils
@@bidenstoletheelection9116 most stuff is manufactured in China and edited to be made in the USA
When I plug my my usb cord into the msd box and into my pc it won’t connect
The 6014 box has to have a 12 volt key switch signal make sure that you have MSD view downloaded on your PC.
Same thing goes for a laptop MSD view software downloaded 12 volt key switch from box.
@@deperformance9741 the box is currently in my truck runs and drives and is powered on a toggle switch I’m am trying to do a custom tune and when I plug the usb into the box and into the pc it doesn’t give me the option to transfer the tune I click send or transfer nothing happens
When you go into msdview software at the bottom where it says file make sure that's lit up green another way to check this is to go to the top where it says connect and transfer the side drop-down menu where your send your files should be lit up black if this is not you have a connection problem between PC and the box check the USB connection between the box and the PC.The file icon at the bottom if lit up green means it is connected to the software if that box is not lit up it's not going to let you receive or transfer files
you might have a connection problem somewhere between the box and your PC
make sure you have a good connection with the USB cord on the box
Make sure the key ignition as to the on position box should be hooked to key switch ignition 12v not constant power
So I can’t use a toggle switch to power my msd box
toggle switch is fine
that's on and off switched power make sure there's a 30 amp fuse in between toggle switch and box
Wow! Look at that WIRING! All that BS to have shitty FI. No thanks I'll keep my carb