This video did show me all I wanted to know :) I am confident that by the help of this I could do the job myself but I am to lazy and lack the tools. My 2012 Ford Transit has leaked oil all over the right rear break discs.. I will get it fixed at repair shop in Finland before they close the border again in a few days because of the corona hysteria (1/3rd the cost of getting it done here in Norway).
just a tip for you,i had so much trouble removing the 65mm hub nut,so i used a jack to jack the breaker bar,made light job of that,loosened realy easy.waiting for parts now.hope this helps others.
My word Paul I'm going to have to stop watching these video's because they bring back a lot of memories of my younger days! (mixed feelings, boy did I get into trouble off my mum when I stripped my mini engine on the kitchen floor!)) You are so right about having the tools for the job. there's only so much you can achieve with a crow bar and a big hammer (ha ha). Thanks for this.
Thank you very much for your instruktive video, sorry for my English. Best wishes from transit owner in Norway. Who is performing the beautiful music. Greetings from Even
@@sharpeysgarage4758 the reason they wouldn't use stainless steel from factory is basically because of the galvanic corrosion between the stainless steel and the steel also stainless steel is not any good for structural used ie suspension components and running gear I would recommend going and changing these back to steal before the galvanic corrosion makes these things harder to get out than the original Steel ones
Hi bud I got stainless m8 x 25 mm from screwfix needed to modify a little but worked fine the abs ring just prys out but be gentle they brake easy good luck bud
Thanks for the video! very informative. I'm planning to do this work soon, however I'm having problems finding the stainless steel screws. Can you please help me find those or just quote the part number or something?
+Toby hi Toby I've not took discs of but from what I've read you will need a puller to pull the abs ring of and maybe some heat I was going to change discs but when I cleaned the discs up they weren't that bad so I would have a good look before you spend any money good luck buddy
well i've started changing the rear discs,,,,,,,grub screws needed chiselling off. stuck now with that 65mm. hopefully someones got one or i'll be on hold until monday.
Mate, thanks for doing this video. It's excellent and helped me a lot. How did you go with those cheap seals? Hope you don't mind me contributing but for anyone reading who's in need of a big torque wrench; you can get the 430Nm required by hanging a 22kg weight on a ridgid horizontal lever at 2m distance from the center of the hub nut. This is the same as 44kg at 1m (if you have that weight available, enough vertical space to accomodate it and someone to assist) but is more manageable. Gym weights would be ideal but a bag of cement plus a couple of litres of water will also give you that weight in a compact package.
Thanks for the input Joel I am sure it will help as for the seals my van was stolen so I can't give an update sorry bud I've have bought a new one so the videos will start again cheers bud
3/4" torque wrench cost me £125 which I thought was good value and was also a Teng quality tool. £25 for the 3/4" breaker bar. So will cost you over £200 just for the tools needed..
If you think this is hard then you have not tried fixing something on a Mercedesl ;) Sometimes it seems they have built the entire car around the thing you want to replace (heating fan and heating system in my case lol)...
Thanks for showing me all I need to to this job by myself! 🙌
Indeed, old school ,change the tyres with spoon, no fancy tools, good job man
This video did show me all I wanted to know :) I am confident that by the help of this I could do the job myself but I am to lazy and lack the tools.
My 2012 Ford Transit has leaked oil all over the right rear break discs.. I will get it fixed at repair shop in Finland before they close the border again in a few days because of the corona hysteria (1/3rd the cost of getting it done here in Norway).
just a tip for you,i had so much trouble removing the 65mm hub nut,so i used a jack to jack the breaker bar,made light job of that,loosened realy easy.waiting for parts now.hope this helps others.
My word Paul I'm going to have to stop watching these video's because they bring back a lot of memories of my younger days! (mixed feelings, boy did I get into trouble off my mum when I stripped my mini engine on the kitchen floor!)) You are so right about having the tools for the job. there's only so much you can achieve with a crow bar and a big hammer (ha ha). Thanks for this.
+Stephen's 8x6 Workshop the good old days changing bike tyres with mum's spoons hehe
I think i will be doing the bearings, seals discs and pads on mine in the near future this video has shown me everything i needed to know Cheers
Thanks sharpey, I diddnt spot the paper gasket you mentioned, which part is it? Many thanks
So I'm guessing the bearings are lubed by the diff oil. Did you put a bit of grease on them for the initial lube.
The left side the screw turn left to put out or the same the right side
GREAT JOB. What transit model is it?
Just doing mine (discs as well) - my hub nuts were literally finger tight! Had no bearing play, recent MOT. Most odd
Awsome video mate. No bs. No mucking around. Ty 👌👌
Thank you very much for your instruktive video, sorry for my English. Best wishes from transit owner in Norway. Who is performing the beautiful music. Greetings from Even
Do you need to apply wheel bearing grease?
very helpfull video ..and yes you need to take abs ring off to change disk ..what a job just to do a disk ..
Cheers I didn't fancy taking the abs ring of so I opted for cleaning the old discs up thanks for the info though
Bet it hurt buying that socket and bar being a Yorkshire man 🤣
Brilliant.. just brilliant!
Great vid, how do you remove disc from hub if need replacing
What size are the grub screws you replaced and where's best to get them mate?
6:07 You really did a better job then factory by choosing those screws
Thanks buddy I don't know why they don't use stainless anyway unless it's the cost
@@sharpeysgarage4758 the reason they wouldn't use stainless steel from factory is basically because of the galvanic corrosion between the stainless steel and the steel also stainless steel is not any good for structural used ie suspension components and running gear I would recommend going and changing these back to steal before the galvanic corrosion makes these things harder to get out than the original Steel ones
Thanks for sharing, made our job easier 👍
Nice video! Great to watch and some sound advice at the end !!
+Machining Basics cheers buddy
Impact driver for the three possi heads mate its a screwdriver you hit with your hammer get them at any motor factors 👍
Lovely jubbly 👌🏻
How are the cheap seals holding up Paul?
Very well and honestly presented informative video
hey sharpey,what size are the grub screws ,i had to drill mine out.thanks
Hi bud I got stainless m8 x 25 mm from screwfix needed to modify a little but worked fine the abs ring just prys out but be gentle they brake easy good luck bud
@@sharpeysgarage4758 thanks,keep up the good work
proper guy excellent video....thanks....
Very nice guide. Thank you
Thanks for the video! very informative.
I'm planning to do this work soon, however I'm having problems finding the stainless steel screws. Can you please help me find those or just quote the part number or something?
Hi sorry for the late if your in the UK I got the screws from screwfix sorry I don't have the item number cheers paul
Avoid stainless steel as you'll end up with galvanic corrosion.
Great video once hub is off is it hard to remove discs?
+Toby hi Toby I've not took discs of but from what I've read you will need a puller to pull the abs ring of and maybe some heat I was going to change discs but when I cleaned the discs up they weren't that bad so I would have a good look before you spend any money good luck buddy
مرحبا اذا ممكن قياس جوان سبي من فضلكم شكراً
also how you pull the abs ring off,thanks
3 leg puller. See th-cam.com/video/NYhXV80L220/w-d-xo.html
Thanks and good video.
well i've started changing the rear discs,,,,,,,grub screws needed chiselling off. stuck now with that 65mm. hopefully someones got one or i'll be on hold until monday.
Great help mate, nice one :) !
brilliant video buddy not looking forward to buying that big socket ,,,,......
Very good video Sir, well done.
Thanks for the video
Mate, thanks for doing this video. It's excellent and helped me a lot. How did you go with those cheap seals?
Hope you don't mind me contributing but for anyone reading who's in need of a big torque wrench; you can get the 430Nm required by hanging a 22kg weight on a ridgid horizontal lever at 2m distance from the center of the hub nut. This is the same as 44kg at 1m (if you have that weight available, enough vertical space to accomodate it and someone to assist) but is more manageable. Gym weights would be ideal but a bag of cement plus a couple of litres of water will also give you that weight in a compact package.
Thanks for the input Joel I am sure it will help as for the seals my van was stolen so I can't give an update sorry bud I've have bought a new one so the videos will start again cheers bud
3/4" torque wrench cost me £125 which I thought was good value and was also a Teng quality tool. £25 for the 3/4" breaker bar. So will cost you over £200 just for the tools needed..
Very Helpful
the music and the accent makes car work, usually frustrating, meditative.
Thanks alot man!
thanks
the engineers sure didn't make this job easy did they.
If you think this is hard then you have not tried fixing something on a Mercedesl ;) Sometimes it seems they have built the entire car around the thing you want to replace (heating fan and heating system in my case lol)...
65mm soquete is very expensive .