👇Sponsor & Any Good Stuff👇 👇影片裡的好東西在下方連結👇 Go check out 4UAD new arrival & lubricant pen 【4UAD 相關商品在下方連結↓↓↓】 🛒🛒 store.4uadsmartairsoft.com/ 🛒🛒 Special Thanks: ➤ Solink Insanely powerful Brushless motor that doesn't get hot 🛒 solinkmotor.com/ ➤ HTA Universal Holster 🛒 facebook.com/profile.php?id=100086214145285&mibextid=LQQJ4d ➤ Perun: For some nice E trigger unit Perun could be an option 🛒perunairsoft.pl/products/etu_plusplus/ ➤ACETECH: you guys do make some amazing tracers and chrono and Targets 🛒Goods : www.acetk.com/ 🛒Amazing Grenades : amzn.to/3EFsI2W 🛒Bifrost Tracers : amzn.to/46UTzER ➤PUFF DINO (恐龍瓦斯): Thanks for supporting us the gas, Puff Dino is the way to Go!!! 🛒Goods : www.puffdino.com/en/category/Airsoft-Gas/E01.html
for some reason when I saw the DSG gear and the bearings I had a feeling something would go wrong🤣 still though, when the bushings came on the thing is a ripper for sure, great work☺
Been running bearings in my dsg with no issues. You just have to make sure that you account for the tolerances between the bearing races and not shim them to tightly.
I love the compatibility that cyma has (since it's a clone) so that I could easily restored my old cyma p90 with etu and high rps build. It s been doing great until now
Excellent work on the Perun Etu. Only things I’d be wary of is 1) get a o-ring air nozzle because better air seal. 2) half a tooth too much was shaved off the piston pickup side, but it shoots fine, as we can all see. And 3) hope those were bushings and not bearings you installed at the end there. Bearings all go boom eventually lol. All in all, good work. Maybe I’ll go install a DSG in my Mp5k now. Lol
What a cool MP5 it looks like the MP5K of special operations are nocturnal that MP5 is asking for a tracer or a silencer and a dbal what a cool what a cool weapon I would love to have one😊
Why are u cutting the gearbox part on 11:31 ? Is it because the selector plate needs to travel a bit further to achieve a precise firing mode (single/auto). I own cyma cm041l and have i think similar problem when I installed perun. When i switch to full auto, sometimes it goes back to single mode (blue light).
Perun is good when you don’t want to connect your phone to the ETU and jefftron sensor sticker is a real pain. So far gate aster is the easiest to install.
Hey, amazing work man! It looks like that mp5 got out of Call Of Duty hahaha. Question here; What nozzle is that? Does it have some sort of rubber tip or something like that?
Nice! I’ve been thinking about doing something similar, but been a little hesitant to do it. Now I know it’s possible and that somebody else has already done it 😂
ปีที่แล้ว +3
Hah! I just recently did a MP5K build based on a CYMA, as well. I also modified the rear plate to take a small 1913 rail for a 5KU stock :D
I'll start with the bad stuff by saying that your shimming and soldering job could need some improvement 😅 Otherwise, I really love these ASMR series, especially when you're giving a new life to an old beaten up gun 👍🏻 Funny how the Cyma MP5K uses this support block for the hop up unit. I have an SRC and there's no such thing, but the gun is pretty heavy as is, for such a small package.
@@4UADSmartAirsoft Sure dude, you can only get better with practice. My first shim jobs were absolutely terrible, so much so that it ended up blowing up the small cylindrical electrical fuses that we had back in the day in our replicas 🤭
So long as your main spring is strong enough to return the piston before the sector completes its cycle there is no need to remove teeth from the piston rack besides minimal weight reduction which again, shouldn't be an issue provided the main spring is strong enough.
That poor deans connector... Your soldering iron tip is f-d. It needs to be covered with solder and stay that way when you're not using it. If done properly you can solder a wire to deans connector in 1-2 seconds. Deans connectors melt easily and if heated for too long the metal plate moves. XT60 is much harder to melt since it's made out of much more heat resistant plastic. Using bearings on a DSG? Are you insane? Only J-Caged bearings can handle it but even they can fail. There's absolutely no point testing if the nozzle seals when it's retracted. It should seal when it's at the forward position, where the AEG fires. Also cutting the whole second tooth is a really bad idea, it puts way too much stress on the pickup tooth on an already high stress build. If the AOE is good you only need to sand down a small bit towards the pickup side. I do it at an angle so that there's still material on the other side so that the sector gear can grab it like it was never sanded.
Thanks for the good tips and it seems like I still have a lot to learn. Eventually in the end of the build I did switch to bushings instead of bearings. We don’t know everything in the beginning, and we are still learning, so please do excuse our mistakes, we will learn from that
@@4UADSmartAirsoft A Solder Mate or Helping Hand is really going to transform your work. When you free solder it like that, the vibrations as the solder sets makes you end up with a dry joint. It'll also let you hold the iron against the blade of the Deans connector to bring the (greater mass) of that part up to temp before then rotating the iron slightly to then include the wire. Wet the iron, heat the blade, flow the solder on to the blade and it'll basically fill the gap itself when both parts are hot enough. You pre-tinned the blade which is a really good start though. But yeah, avoid vibration as you solder like the plague. Good luck, we like your videos 👍
![[UNBOXING] CYMA CM.060 P90 SMG - one for the Stargate fans!](/img/n.gif)
👇Sponsor & Any Good Stuff👇
👇影片裡的好東西在下方連結👇
Go check out 4UAD new arrival & lubricant pen
【4UAD 相關商品在下方連結↓↓↓】
🛒🛒 store.4uadsmartairsoft.com/ 🛒🛒
Special Thanks:
➤ Solink Insanely powerful Brushless motor that doesn't get hot
🛒 solinkmotor.com/
➤ HTA Universal Holster
🛒 facebook.com/profile.php?id=100086214145285&mibextid=LQQJ4d
➤ Perun: For some nice E trigger unit Perun could be an option
🛒perunairsoft.pl/products/etu_plusplus/
➤ACETECH: you guys do make some amazing tracers and chrono and Targets
🛒Goods : www.acetk.com/
🛒Amazing Grenades : amzn.to/3EFsI2W
🛒Bifrost Tracers : amzn.to/46UTzER
➤PUFF DINO (恐龍瓦斯): Thanks for supporting us the gas, Puff Dino is the way to Go!!!
🛒Goods : www.puffdino.com/en/category/Airsoft-Gas/E01.html
Bro made one of the best replica i ever seen out of a cyma
AMAZING WORK
Thanks buddy, glad you like it
@@4UADSmartAirsoft may I ask why you cut the first tooth on the cylinder?
@@GameChameleonChannel It's part of "AOE correction". I'm too lazy to explain it here, but google it if you're interested :D
Outstanding job as usual!
The custom Picatinny rail for the stock was just the cherry on top 👌
That is my favorite part of this aeg
ooh that end course (especially at night, max lense flare) looks awesome
Haha thanks man glad you like it
artisan mcx fold stock + mp5k , perfect combination
I would love to see more restoration videos like this
I do enjoy restoration videos too
Amazing work. Very clean and i love the rear rail add on!!! Smart!! 👏
haha thanks man this works with all Mp5 aegs
for some reason when I saw the DSG gear and the bearings I had a feeling something would go wrong🤣
still though, when the bushings came on the thing is a ripper for sure, great work☺
yah no more bearings man no more
Been running bearings in my dsg with no issues. You just have to make sure that you account for the tolerances between the bearing races and not shim them to tightly.
I love the compatibility that cyma has (since it's a clone) so that I could easily restored my old cyma p90 with etu and high rps build. It s been doing great until now
Oh gawd that soldering skills are killin me😂
Sorry bro i needed some more work
Emotional. good video.
I like this.
Thanks buddy
The Gun looks insane bro!!!
Thanks buddy
Yes. More aeg ❤
Will do
Sub'd! Don't know how I haven't discovered you before. My new favorite airsoft channel! P.S. Get some solder flux. 🙂
Haha thanks man we will keep the contents coming!
Excellent work on the Perun Etu.
Only things I’d be wary of is 1) get a o-ring air nozzle because better air seal. 2) half a tooth too much was shaved off the piston pickup side, but it shoots fine, as we can all see. And 3) hope those were bushings and not bearings you installed at the end there. Bearings all go boom eventually lol. All in all, good work. Maybe I’ll go install a DSG in my Mp5k now. Lol
Thanks for the good tips man and yah no more bearings for sure, and I still need to work on my shimming skills
I always start my shimming bevel to pinion first. It's the hardest part to get right but my guns make almost zero gear noise.
Yes after doing some high speed single sector builds I am done using bearings. Bushings are the way to go.
Can’t agree more lol screw bearings
What a cool MP5 it looks like the MP5K of special operations are nocturnal that MP5 is asking for a tracer or a silencer and a dbal what a cool what a cool weapon I would love to have one😊
Very nice pal good job!
Nice coat hanger
1:55 司馬(CYMA)的電動槍系也算是時代的眼淚了 老屁股才知道
超級難找
Why are u cutting the gearbox part on 11:31 ? Is it because the selector plate needs to travel a bit further to achieve a precise firing mode (single/auto).
I own cyma cm041l and have i think similar problem when I installed perun. When i switch to full auto, sometimes it goes back to single mode (blue light).
I guess its because the mp5k we used was super old
thank you master, sensei
No my friend I still have a lot to learn
Good luck on the difficult patch
Work of art man, how on earth did you learn all this? 🙌🏻💪👏
Haha nah I still have a lot to learn
kwa usp match 適合用嗎？？有防搶槍安全鎖嗎？？
適用喔但不防搶
How do I get one of this in Iraq
I don’t know to be honest
Did you use a brushless in this?
Lol, thanks to you we get to make this one. haha yes solink motors were used in n this video.
Gotta be a small battery, the rps feels too slow for a brushless and DSG combo. ANy more brushless videos coming up? @@4UADSmartAirsoft
Sooo cool🎉
What was the cost of the full upgrades ?
트리거가 길어서 방아쇠울에 방해가 될듯한데ᆢ장착이 가능한가요
18:11 this is the definition of frustration
I really like the looks of that holster. But is it still in development or is it available to buy? The only link is a facebook page.
they only have their facebook page, but yah that holster kinda fits everything
Hello, is the drum mag from G&G? 片尾用的請問是G&G彈鼓嗎？
是滴
that was ao cool.
any chances for lambada defense ghm9 gbb?
I will put it on my list
what is your preferred mosfet/etu for version 3 gearboxes? is it the perun v3 hybrid? It looks alot harder to install than the perun v2 hybrid.
Perun is good when you don’t want to connect your phone to the ETU and jefftron sensor sticker is a real pain. So far gate aster is the easiest to install.
Hi. What is the name of this stock ? Ty
wat stock is that? is it for the sig or can buy it separately ?
Search for 5KU Skeleton stock. This specific version is sold as "5KU Skeleton Stock Visor Helmet"
I'm not sure who makes the original one.
@@error262 thanx man wouldnt have ever figured it out on my own
5ku sell those separately
@@4UADSmartAirsoft tnx man awesome vid wish i had that much arsenal to play with hahah
sick! 😍
Hey, amazing work man! It looks like that mp5 got out of Call Of Duty hahaha. Question here; What nozzle is that? Does it have some sort of rubber tip or something like that?
It’s actually a homemade nozzle since the old one is too short, in increase the length so it gets a slightly better air seal
Nice! I’ve been thinking about doing something similar, but been a little hesitant to do it. Now I know it’s possible and that somebody else has already done it 😂
Hah! I just recently did a MP5K build based on a CYMA, as well. I also modified the rear plate to take a small 1913 rail for a 5KU stock :D
Hahaha great minds thinks the same
Добрый вечер подскажи пожалуйста сможешь на заказ зделать такую малышку
Sorry buddy this one is just a custom for videos
Fantastic!
司馬當活馬醫👍🏿
哈哈哈哈哈這個梗猛！ 讚爛
mp5 my love
what battery did you use
A long stick type battery for Mp5K
fantastic～
Thank you! 😊
Incroyable
I love this stock, can you give me the link?
Check out 5ku
Waiiit. You didn't grind those extra teeth from the front?
damn, what's the stock? :o looks so good, I want it!! especially since I use a full face mask
its a stock designed by sig, 5KU sells it :D
Spedisci anche in Italia? 😂
“It’s perfect”
You made me buy one …..
lol good luck buddy haha
am i too early for this it feels illegal bro 😂
初速波动好像有点大哦
這把槍～～～～難喔
Are the fps too low?
從載卡多下來還蠻帥的。
真的不錯帥~~
I'll start with the bad stuff by saying that your shimming and soldering job could need some improvement 😅
Otherwise, I really love these ASMR series, especially when you're giving a new life to an old beaten up gun 👍🏻 Funny how the Cyma MP5K uses this support block for the hop up unit. I have an SRC and there's no such thing, but the gun is pretty heavy as is, for such a small package.
Haha thanks man and yah I really needed more work on the soldering as well as the shimming part. Will get more practice going
@@4UADSmartAirsoft Sure dude, you can only get better with practice. My first shim jobs were absolutely terrible, so much so that it ended up blowing up the small cylindrical electrical fuses that we had back in the day in our replicas 🤭
帥
謝！
不是吧上一個影片，才講dsg和bldc馬達，這一部就來了😂
可惜沒用dsg用的尾頂杆，所以初速低了點
對啊手邊買的到的東西有限不然確實希望初速可以再高一點
So long as your main spring is strong enough to return the piston before the sector completes its cycle there is no need to remove teeth from the piston rack besides minimal weight reduction which again, shouldn't be an issue provided the main spring is strong enough.
That is kind of true but since I could only find a m140 spring on my shelf I decided to grind off the teeth. Will see how long it last
You are good at a lot of things but those solder joints look ROUGH! Other than that nice job.
haha yah I got that alot let me work on my soldering skills
Hey what about AOE, i didn't see proper AOE as you usually do ^^
Haha I still need quite some practice when it comes to dsg aoes
期待開箱魷魚牌短劍GBB
我們努力
Brrrrrrrrrrrrr❤
That poor deans connector... Your soldering iron tip is f-d. It needs to be covered with solder and stay that way when you're not using it. If done properly you can solder a wire to deans connector in 1-2 seconds. Deans connectors melt easily and if heated for too long the metal plate moves. XT60 is much harder to melt since it's made out of much more heat resistant plastic.
Using bearings on a DSG? Are you insane? Only J-Caged bearings can handle it but even they can fail.
There's absolutely no point testing if the nozzle seals when it's retracted. It should seal when it's at the forward position, where the AEG fires.
Also cutting the whole second tooth is a really bad idea, it puts way too much stress on the pickup tooth on an already high stress build. If the AOE is good you only need to sand down a small bit towards the pickup side. I do it at an angle so that there's still material on the other side so that the sector gear can grab it like it was never sanded.
Thanks for the good tips and it seems like I still have a lot to learn. Eventually in the end of the build I did switch to bushings instead of bearings. We don’t know everything in the beginning, and we are still learning, so please do excuse our mistakes, we will learn from that
If at the end this mp5 sounds like M134-A2 Vulcan imma dislike and write you a mean comment.
Thanks for the mean comment hahaha
HOW TO GET THESE AIR SOFT GUNS IN INDIA ?
Saar me airsoft saar WHY DO YOU REDEEM IT
嗯??? 我眼睛看錯嗎? LCT的BOX?
好像還有火力的缸頭跟神龍的天梯
哈哈哈對來的時候就是一袋子亂七八糟的東西
a total fake, I’ve never seen a gearbox so clean, it was obviously prepared in advance, or even a new one was assembled for the video.
Ok whatever you say~~~~
sell me that pls ...
:DDDDD
This man takes a cool looking gun and makes it sound like a Drill on lowest gear. Stop this man or he will ruin even more toy guns like this one.
；ㄗ
Yeah I'd keep it out of focus too if I soldered like that.
Now the master speaks
@@4UADSmartAirsoft A Solder Mate or Helping Hand is really going to transform your work. When you free solder it like that, the vibrations as the solder sets makes you end up with a dry joint. It'll also let you hold the iron against the blade of the Deans connector to bring the (greater mass) of that part up to temp before then rotating the iron slightly to then include the wire. Wet the iron, heat the blade, flow the solder on to the blade and it'll basically fill the gap itself when both parts are hot enough. You pre-tinned the blade which is a really good start though. But yeah, avoid vibration as you solder like the plague. Good luck, we like your videos 👍
@@kiztime1234 Dude I'm taking some serious notes man, thanks for the awesome tips. I will get more practice with your method for sure! Thanks man!
It’s a machine gun bro, It’s a fuxking machine gun !!
Haha sub
這種玩具槍在中國已經足夠把牢底坐穿了。
這樣的話瓦斯槍不就把牢給坐沒了?
那我完蛋了～超級通緝犯
那倒不至于，70m/s的初速刚好在比动能1.8j/cm2的红线以内，电动的还是安全的
One of the absolute worst parts of airsoft teching has to be Soldering
Hahaha not gonna lie it’s kinda true
Hi, I'll give you $500 dollars
Damn bro
am i too early for this it feels illegal bro 😂
What stock is that?