Just did the job the video helped however you do not have to remove the air pump or the throttle body at all. You can take the bracket off throttle body and use a swivel socket to get the hard to reach bolt and since nothing is protruding from the thermostat housing. It slides right out. You will need to have some hose clamps ready as the factory quick connect disintegrated the car has been in Georgia and Arizona. No rust 158,000, miles. My Latino brother is a master of all!
I have been working on cars for 37 years and vehicles are getting more complicated your right engineers have nothing better to do then make things complicated any ways thanks for the video good explanation
They don't get complicated they make them complicated intentionally. Like wide open. So that people like you stop working on them so that to direct people to their stupid dealerships and charge a turn of money. Me I call it a few white selfish tricks that can't get enough with what they have.
What a nightmare this looks like. I have done lots of thermostats but this looks like things could go wrong like the quick connection coolant hoses snapping seals can leak knowing my luck but I got to just do it that's all. Thanks for all the details and nicely explained on the video 👍👍👍
Damn good video right here!!!! Out of all the videos I've watched this video right here lets you know everything with details and every type of problem you're going to come in contact with...⭐⭐⭐⭐⭐... Keep up the good work brother I just subscribed to your channel
You know I'm going to say one last comment about this job and taking the starter off of it Chrysler Chrysler should have been brought up on criminal charges for this
What's the hose called that connects to the aluminum / metal pipe that runs along the front of the engine.. The hose also connects to the thermostat reservoir.. my hose broke where it connects to the thermostat reservoir
That is why this company failed. The seat down and hire people to make everything hard to open so you take it to the dealer. We are living in a bad world.
I'm going to sit here and comment it comment at this at 1 minute and 13 seconds because like this is the one job I will not do is that also what you got to do to take the starter off????
This is by far the best video i've seen for the 2.4l thermostat...nice job and I appreciate your time and hard work
Just did the job the video helped however you do not have to remove the air pump or the throttle body at all. You can take the bracket off throttle body and use a swivel socket to get the hard to reach bolt and since nothing is protruding from the thermostat housing. It slides right out. You will need to have some hose clamps ready as the factory quick connect disintegrated the car has been in Georgia and Arizona. No rust 158,000, miles. My Latino brother is a master of all!
I have been working on cars for 37 years and vehicles are getting more complicated your right engineers have nothing better to do then make things complicated any ways thanks for the video good explanation
Probably easier to replace the engine.
They don't get complicated they make them complicated intentionally. Like wide open. So that people like you stop working on them so that to direct people to their stupid dealerships and charge a turn of money.
Me I call it a few white selfish tricks that can't get enough with what they have.
What a nightmare this looks like. I have done lots of thermostats but this looks like things could go wrong like the quick connection coolant hoses snapping seals can leak knowing my luck but I got to just do it that's all. Thanks for all the details and nicely explained on the video 👍👍👍
ive done this recently nd everything hes saying is right on the money and it was a total and complete nightmare
Damn good video right here!!!! Out of all the videos I've watched this video right here lets you know everything with details and every type of problem you're going to come in contact with...⭐⭐⭐⭐⭐... Keep up the good work brother I just subscribed to your channel
Great video, looks challenging
I didn’t see the removal of rear bolt? Did I miss it?
I am saying the same no removal of the hardest bolt he just wasted my whole time.
Good job and nice video.
What wrench did youse for the lower back 10 mm bolt
You know I'm going to say one last comment about this job and taking the starter off of it Chrysler Chrysler should have been brought up on criminal charges for this
Showed everything but how to remove the one bolt that’s hard to remove 😂
Hi. why did you not just changed the inside thermostat? why to change with the housing? thats metal part
I'm trying to replace a starter... Damn second bolt hard to get too from transmission side
Just did this today, that bottom bolt in the back makes this a lot harder than it needs to be.
Good job 👍
What's the hose called that connects to the aluminum / metal pipe that runs along the front of the engine..
The hose also connects to the thermostat reservoir.. my hose broke where it connects to the thermostat reservoir
How did you get the one off the top? Right above the sensor
Smh just like every other vid on yt you dont show the actual hard part yall need to do better. How the hell you get back bottom bolt
And just because he did not show me how to remove that hard ass bolt that’s why he got a dislike
That is why this company failed. The seat down and hire people to make everything hard to open so you take it to the dealer. We are living in a bad world.
Warranty time pays u 2 hours to get it done
I changed my name and cut my hair before I put a starter on one of these or a thermostat
I'm going to sit here and comment it comment at this at 1 minute and 13 seconds because like this is the one job I will not do is that also what you got to do to take the starter off????
Brother I gotta do this on my car un freakin real I think I wanna sell this car
It wont need to reset
Am doing one right now and the bottom right bolt on the thermostat is giving me hell.i hate these cars.stupid design.