Echo cs680 Chainsaw Ignition Coil Replacement

A customer brought in an Echo CS680 chainsaw complaining that it wouldn't start. It was diagnosed as needing an ignition module but this coil is a little different than most. #smallenginerepair

[@Safteassemblies]

Hello there brother , i know i did exactly like you , then i couldnt get my air gap guage cardstock back out ,all i could think off and i didnt do it was to take off the plastic fan off the flywheel witch involves upsetting the starter pawls and i seen bad things happening to happen after that so i didnt do it . To set the airgap im refering too. Rockon brother love the vidios. You make cause you keep it real. . hellyeah

[@chrismartin4776]

CS 680 is my favorite saw. I really like the manual oiler option to add extra bar oil to the chain.

[@chainsawredeemer85]

Good job neighbor!

[@alans.4658]

Thanks Scott! After watching and learning I feel like firing up my Echo CS490. It's a good saw, just lacks a better antivibe setup.

[@tedneitzel]

Yep never done a 680 coil before so yea nothing to add from me! Well done as always!

[@MrRmh3481]

For the 670/680 you dont take the flywheel off, instead remove the starter pawls and lift off the nylon fan. Replace the module, set the airgap from above. Take care, enjoy the vids.

[@TheGreasyShopRag]

Thanks! I knew there had to be a better way but never really gave it much thought till I was editing video. Now I'm hoping a dead 680 will come into the shop.

[@Safteassemblies]

There it is rite there , to pull the plastic flywheel. Just was telling that thats was the only way to get thr airgap proper . Otherwise , goodluck eyeballing cause you cant do it accurrate otherwise . I admire your knowledge and thank you . All should listen to your advice here . All ....

[@TheGreasyShopRag]

@@Safteassemblies Thanks for the kind words and thanks for watching!

[@chrischiampo7647]

I Use 2 Pieces of Microfiche Stacked Together and Trimmed to Gap The Coil on These More Flexible Than a Feeler Gauge 😀😎👍🏼

[@TheGreasyShopRag]

I haven't heard anyone use the term microfiche in a couple decades. I know we threw all those away.

[@chrischiampo7647]

@@TheGreasyShopRag All Our Old Shop Parts Manuals Were on Microfiche and I Saved Some For This Purpose and I Also Wrap A Piece Around The Crank Shaft on Some Engines Mostly 4 Strokes To Install Crank Seals So They Don’t Hang Up on The Lip of The Crank 😀👍🏼😊 Ol School Trick

[@TheGreasyShopRag]

@@chrischiampo7647 Good tips. Thanks.

[@Doc-Cole_Trickle-of-Chainsaws]

👍🆙S

[@SurvivalInFlames]

Any chance of getter the part number and manufacturer of those spark plug wire pliers?

[@Rustychainsaws]

Where did you buy the pliers for the wire?

[@TheGreasyShopRag]

Husqvarna part #502 50 06-01 Assembly Pliers.

[@rooster3019]

"Oil" to lube the rubber? Tire lube or soapy water or silicone spray I have used. Never tried oil, is it 2 cycle oil, motor oil other?
I have never seen a coil shaped like that, what were they thinking???

[@TheGreasyShopRag]

"Fluid Film" is a lanolin based lubricant. I've never had any problems using it on rubber although the company states it should only be used on oil resistant rubber. I hope they are just covering their butt.

[@rooster3019]

Ha! If Mr. Obama taught us anything, it is that HOPE is not a plan. lol

[@theamerican7080]

I guess slamming it on the workbench a couple of times helps.

[@TheGreasyShopRag]

No chainsaws were harmed in the filming of this video. Its all theatrics. Thanks for watching and taking the time to comment.

[@theamerican7080]

@@TheGreasyShopRag Of course! I did enjoy the video, however. Thank you for taking the time to help others.

[@jonathanfierberg3807]

Cheesy no boot or terminal