You are an amazing guy, the you teach it is incroyable...so amazing......the way you teach even those who did not go to school will understand and becoming more powerful as well...around the world does love your videos
Thank you very much sir granted narin ung matagal ko ng inaabangan 👍 done watching sir malakeng tulong to pag may problema crane namin kaya ko ng ayusin❤️👍👍👍
WOOOOOW, You are just amazingly explaining in simple & comprehensive way... Are u from Philippines Sir, I've worked with Philippines engineers, they're so skilled
Oo sir panoorin nyo pra makakuha kyo ng magandang idea. Maganda ang title ng channel nyo sir. Pero kelangan ang content ng video nyo ay gandahan nyo pa, pra ma encourage mga viewers. At tapusin hangaang dulo. At kelangan bawat uplaod nyo na video ay maganda ang title… i mean Ung searchable sa youtube.
yes bro even in the books always stop and start button. bứt the connection is same ,” stop button is connected to coil,” if you press stop button power di energize. we have some hoist the same like that. and some hoist no start button they use emergency stop only. if you press emergency stop power dis able and once you release contactor energize power circuits on.
Tamsak done master watching na Sir yong swicth na up and down at switch left and the right ay momentary switch wala syang maintaining contact sir tama ba ako tnx
we have also 3 bridge crane we use emergency stop only, when you press stop contactor de energise, and when you release magnetic contactor energize that is no need to connect holding contact because direct to A1 coil.
master.. tanong lng.. may ginagawa ako ngaun hoist machine galing china 10t bakit ung main motor may 5 terminals power input . napagana ko na left and right and forward backward. up and down nalang kulang ko lahat 3phase220v ang motors. pano kaya wiring diagram ng main motor up/down with 5terminal.wires . salamat po sa pgsagot.God bless
The Control System is JOG JOG SYSTEM WITHOUT AUXELLARY SYSTEM BECOZ THE R&F IS WITH INTERLOCK NO CANNOT PRESS FORWARD UNLESS YOU PRESS STOP PUSH BUTTON
Hello konan, how to identify 6 leads without marking? Easy , you need voltmeter and set on continuity. to test and find the wire together, take one wire and test continuity if ok, mark #1 end mark # 4. Next take one wire mark # 2 find continuity end and mark # 5, and last mark #3 and mark # 6, then if find both end connect supply. If wont turn just humming turn off power so that winding wont burn. Change connections until you get the right. Try again .
Unang problema na dapat mong check.. buksan mo ang push button minsan lose wire connection, or yung poor contact yan ang madali at unang check. Pag okay check mo sa taas meron fuse yan baka busted. Next baka napatid na ang wire sa loob ng cable ng cable check mo continuity.
masmaganda kung remote control kse wala ng pendant , bihira masira battery lang palitan. pag nalowbat at pag dlown fuse sa taas ng control box. pero ung wirin connection ng motor up/down and forward/reverse ganyan padin.
Awesome video tutorial nice diagram and very clear explanation how to wired and installations thanks you so much sir
Thank you very much i dol victor for your support.”❤️
You are an amazing guy, the you teach it is incroyable...so amazing......the way you teach even those who did not go to school will understand and becoming more powerful as well...around the world does love your videos
thank you 🙏
Thank you very much sir granted narin ung matagal ko ng inaabangan 👍 done watching sir malakeng tulong to pag may problema crane namin kaya ko ng ayusin❤️👍👍👍
Thank you idol atleast natupad narin matagal mo ng request . Enjoy watching and learn.
I’m watching again sir maraming salamat talaga very clear explanation 👍👍👍🙏
Thank you idol for your support ❤️👍 kayang kaya muna gawin at troubleshoot ngayon yan. Good luck.
Great video super easy to understand. Please keep up the good job you're doing!!!
thank you
Thank u Po master...now ko lng Po naintindihan yung working principle nyan
maraming salamat at napunta ako sa channel mo sir. god bless po,laking tulong po sa aming baguhan sa electrical ang pagshare ng kaalaman nyo po.
@@xiaandonel9718 ayus yan sir marami kang matutunan dito
Very nice . Thank you for explanation of hoist/ cran control
you’re welcome
Very interesting content master TM. Great sharing your knowledge and ideas. 👍👍
Thanks 🙏
Nice video tutorials sir complete details maraming salamat sa effort nyo god bless po
Thank you idol
Great content. Please post more videos. Thank you for sharing your knowledge with us.
Thank you, I will make more videos
Very helpful this video thanks for sharing
WOOOOOW,
You are just amazingly explaining in simple & comprehensive way...
Are u from Philippines Sir,
I've worked with Philippines engineers, they're so skilled
Thank you so much mr malik for you nice comment. Yes im from the Philippine how bout you where you from?
Appreciate.thanks.very helpfully presentation.
thanks 🙏
okey, sir bigay ulit nang diagram ,thank yuo para ,matuto pa,sa industial,,,,
thank you in advance master, but why stop push button didn't come first. in your ckt first is start button ; thank you keep it up
yes i know . but doesnt matter the stop button is connected in same circuit .
i trouble shoot one of our hoist same diagram i make.
@@tmelectricaltutorials2851 thank you master
your welcome brother
Very informative po sir🙂👌👍
Thank you 🙏
Very interesting..thank you for sharing brather
Thank you brother
Best video I've seen this far on this hoist crane .
Please explain where do you get your Neutral from hehe??
Must be installed the control transformer inside the panel . If primary voltage is 240 tp 600 volts ac the load side is 110vac
Ang galing mo nman master.
Maraming salamt po🙏
Good lecture. Great demo
thank you
panoorin ko mga video mo para makakuha ng idea
Oo sir panoorin nyo pra makakuha kyo ng magandang idea. Maganda ang title ng channel nyo sir. Pero kelangan ang content ng video nyo ay gandahan nyo pa, pra ma encourage mga viewers. At tapusin hangaang dulo. At kelangan bawat uplaod nyo na video ay maganda ang title… i mean Ung searchable sa youtube.
Bago lang ako dito sa youtube sir,” kaya still i need more improvement.
must be from philipins hahah nice video
Yes bro im from the Philippine owino.
this guy is great big up sir
Thank you owino
Terimakasih pak ilmu yang sangat bermanfaat.senang dengan anda juga conten anda.salam dari indonesia. Breakenya tida di conek ya pak?
your welcome to my channel sir
Maraming salamat po master.god bless po.
Nice good teaching 👍 sir
Thank you bro
Ive been looking at building a trainer board just like this. Do you have a list of parts you used?
I was always told the stop should come first in the circuit for guaranteed safety. Do cranes commonly have the start button first?
yes bro even in the books always stop and start button. bứt the connection is same ,” stop button is connected to coil,” if you press stop button power di energize. we have some hoist the same like that. and some hoist no start button they use emergency stop only.
if you press emergency stop power dis able and once you release contactor energize power circuits on.
mag content din po kayu na may inverter sir for long travel wiring diagram
meron din akung ginawang Eaton drive VFD panoorin mo, picturan muna ang diagram .
Very good teaching
thak you for sharing,, greatfull sayo TM ELECTRICAL.....
Thank you so much bro
can you do a tutorial showing how to connect load limiter to hoist?
Thanks 😊 man
Tamsak done master watching na Sir yong swicth na up and down at switch left and the right ay momentary switch wala syang maintaining contact sir tama ba ako tnx
O boy momentary contact mga un tama ka.
Hi very interesting about your video electrical installation but can you explain in English?
Salamat master
Thanks bossing
Thanks master
Mukang dimo mong pinanood bro thank you
Why not go to stop button straight from main fuse ? I guess it will still open the main contactor.
we have also 3 bridge crane we use emergency stop only, when you press stop contactor de energise, and when you release magnetic contactor energize that is no need to connect holding contact because direct to A1 coil.
Thank you.
master.. tanong lng.. may ginagawa ako ngaun hoist machine galing china 10t bakit ung main motor may 5 terminals power input . napagana ko na left and right and forward backward. up and down nalang kulang ko lahat 3phase220v ang motors. pano kaya wiring diagram ng main motor up/down with 5terminal.wires . salamat po sa pgsagot.God bless
trace mo kung saan papunta ung input.baka ung tatlo para sa main contactor yung dalawa para sa control transformer step down .
@@tmelectricaltutorials2851 salamat master👍 cge trace ko .
walang problema mg tanong ka lang . saan lugar kaba?
boss hamap pa sa panas yung camera mo boss maganda sana kaso barged yung video mo
kaya nga eh bumili na ko ng bagong camera .
The Control System is JOG JOG SYSTEM WITHOUT AUXELLARY SYSTEM BECOZ THE R&F IS WITH INTERLOCK NO CANNOT PRESS FORWARD UNLESS YOU PRESS STOP PUSH BUTTON
korek
hindi na po ba kailangan ng overload para sa motor sir?
hindi na kelngan yan ng overload lase kung lagyan ng overload nasa taas d lageng akyatin sa taas . most goist wala ng overload
@@tmelectricaltutorials2851 ganun pala yon sir,kaya pala fuse ang gamit..maraming thank you po ulit sir..god bless po happy new yr 😉❤️
Thank you sir, please do how to re identify motor leads UVW1 and ends UVW2 when motor has no labels
Hello konan, how to identify 6 leads without marking? Easy , you need voltmeter and set on continuity. to test and find the wire together, take one wire and test continuity if ok, mark #1 end mark # 4. Next take one wire mark # 2 find continuity end and mark # 5, and last mark #3 and mark # 6, then if find both end connect supply. If wont turn just humming turn off power so that winding wont burn. Change connections until you get the right. Try again .
@@tmelectricaltutorials2851 sir thank you for clarifying
Sir wala ng limit switch yong left and right control circuit tnx sir
Walang limit switch pero both end meron metal stopper. Pra hindi malaglag ang buong panel unit pati motor for safety.
@@tmelectricaltutorials2851 tnx sa info sir tnx din sa vedio
@@boybravo689 you’re welcome bro mg subscribe ka pra sa pag may bago akung video updated ka.
Boss taga canada ka ba? Ano work mo jan sa Toronto?
Oo sa canada ako sa toronto , ang work ko is industrial electrician
Sir yong motor 3 phase 3 leads out tama ba ako sir
3 phase supply ng dalawang motor. Thanks for watching boy
❤
Sir yong motor para sa up ang down paano ang wiring diagram kasi meron syang brake coil
Yung brake coil two wire supply un nakakabit na sa terminal supply ng motor mismo sa box ng motor.
@@tmelectricaltutorials2851 sir ibig sabihin may sariling motor na nakakabit sa gearbox sir tnx sa video beginner pa lng ako sir
@@boybravo689 oo bro ung motor nakakabit na ang gearbox
Panoorin mo ung unang video ko na hoist diagram andun ang complete detail na diagram ng brake coil . Picturan mo.
@@tmelectricaltutorials2851 tnx sir
ilang amperes po yong fuse na gamit ng para sa kada motor po sir?
mostly ang fuse ng motor 3amps lang to 6amps depende sa rating ng motor. kahit maliit ang motor malakas kase connected to gearbox.
thank you po sir,god bless po ❤️
Sir mag tuturo po ba kayo ng 1on1? Zoom or messenger po?
hindi sa you tube lang panoorin video ko, ung mga ksama ko sa work swerte nila
saan ka po sir sa canada ka po ba?
Sir pede overhead crane three phase two speed motor. Thanks po
Pinag iisipan ko kung gagawa ako ng two speed ganyan din kalabasan ng diagram at ang madagdaga lang yun second speed.
ControlCircuit is about to finish wiring before wiring the Power Circuit so that aware of mistake
korek
Sir no reverse ang motor hoist anong problem kaya? Salamat sa sagot
Unang problema na dapat mong check.. buksan mo ang push button minsan lose wire connection, or yung poor contact yan ang madali at unang check. Pag okay check mo sa taas meron fuse yan baka busted. Next baka napatid na ang wire sa loob ng cable ng cable check mo continuity.
@@tmelectricaltutorials2851 salamat po
Pano po pag mag a add ka brake para sa crane hoist.
Kasama na yung brake sa motor nakakabit na. Ang tawag dun ay brake motor. Pag kinabit mo supply gagana na dahil naka connect na sa terminal ng motor.
Paano Kung remote control sir
masmaganda kung remote control kse wala ng pendant , bihira masira battery lang palitan. pag nalowbat at pag dlown fuse sa taas ng control box. pero ung wirin connection ng motor up/down and forward/reverse ganyan padin.
Pwde sir makahingi Ng wiring diagram Ng remote control Ng f-23A++(s)
pag tinawag ako sa kabilang planta sa work ko. try ko hanapin diagram picturan ko .meron kaming crane apat na ganun.
Salamat po sir
Gandang hapon po sir pwde sir magtutorial K remote control Ng crane wiring