P0192 Fuel Rail Pressure Sensor Replacement Mazdaspeed 3 6 Mazda CX-7 2.3
ฝัง
- เผยแพร่เมื่อ 22 ม.ค. 2024
- P0192 Fuel Rail Pressure Sensor Replacement for Mazdaspeed 3 Mazdaspeed 6 Mazda CX-7 2.3.
In this video , I share my experience on how to replace your fuel rail pressure sensor if your car is hesitating or has a check engine light on your dash with the code P0192. This is a complete beginner guide for those who has never done an install on a fuel rail pressure sensor and will solve that problem.
Please be advised, This is not a sponsored video, I'm are not responsible for any damage or injury occurred to you , your parts , or your car whatsoever. This video is meant for entertainment purposes only , do not attempt if you don't have the proper tools or damage & injuries may occur. Thank you
Part number for Bosch Fuel Rail Pressure Sensor :
www.summitracing.com/parts/BC... - ยานยนต์และพาหนะ
Thank you for putting this up, my brother! You made it look easy!
You’re very welcome . I hope this helps .
Very good work
Thanks a lot
Good Stuff, My dumbass over tightened it when I did this a while back and ripped out the threads. Glad yours came out well.
I’m so sorry to hear that it happened to you . I was very careful when fighting because of how the sensor was small . And I appreciate your support .
I had this same issue and replaced the sensor with the same Bosch part. It worked well for about a month and then the code came back. I hope you have better luck.
Thank you for letting me know , it’s been two weeks so far , and I haven’t had an issue with it whatsoever . So I’ll keep you updated if any changes has occurred in the near future .
So yours has been fine? No whistling noise or not able to go over 1500 psi on your hpfp (issues i had with mine) I tried 4 different sensors including 5053 and none worked, different issues with each. The only one that would work is the oem 5006 sensor, had to buy a used oem fuel rail to get the sensor. These cars are weird sometimes.
I’ve had the sensor installed for more than 5 months , and the car is still running with literally no issues whatsoever. No leaks at all , no hesitation at all , and no check engine lights or codes. I’m not sure why I’m receiving a lot of complaints regarding this sensor, but it’s been working fine with me . If it doesn’t work for you , then yes try to find an OEM one that’s been used. Dealerships will try to sell you the entire fuel rail with the sensor , they don’t sell the sensor by itself unfortunately. I’m sorry you had to go through this brother .
Great vid. Part number not in stock :(
No worries at all. eBay sells them as well. Make sure to enter the exact part number that’s on the sensor. There’s loads of them.
@@Meanmachine.ms3 thank you sir
Bosch part failed on mine and went back to oem. I would recommend just unplugging the negative terminal on the battety while you replace the sensor. Theres no need to pull and fuses.
Thanks for letting me know and I’m sorry that your part has failed. I’ve had mine installed since January, so it’s been more than 4 months and the car is still running strong and I’ve had zero issues whatsoever. The reason why I pulled the fuse is to make sure that there is no fuel in the fuel rail and no fuel leaks when removing the sensor. That’s all.
Me second gen when exit a corner or getting on the highway right after a hard turn if try to accelerate hard it just bogs out, then just acts normal, sometimes it does it on the straights too, I change that sensor, change the high pressure fuel pump,clean injectors..... sometimes i think n theres something on the fuel tank...
Any update on this repair? Did it last? Any leaks developed? Did yiu confire actaul FPR with desired FPR?
I’ve had this sensor for more than 2 months , and the car is still running with no check engine lights whatsoever. There is no leaks at all , I check it every week on a Saturday morning, and the car starts with no hesitation.
Is still working great the sensor?
Yes , It is still working , running strong , and I’ll be uploading another video this week.
Have you cleaned your maf senor
Brand new MAF Sensor from Mazda was installed 10 months ago.
How's it holding up? Is it leaking? Has the car still been running strong?
Yes , the car is still running and holding strong . And I will be uploading another video this week as well .
Thank you! I plan on buying the part later today
@@angeluscollective that’s awesome. Hopefully you find this video helpful
Bro let me know if you want me to come help you with stuff!
I’m gonna need some help with a cool project that I’m gonna be doing . 😅
No codes