I'm Impressed . You did a great job fabricating everything . I'm getting one soon , I think I'll keep the trim on and just seal at the joints top and bottom . Love the Flag ! Thanks
I just picked mine up from Academy in Killeen Texas ,that and a Minn Kota 50lb thrust Endurance trolling motor for 579$ they loaded it up after I inspected it and 💥 bam I was on my way home. I’m so excited about the mods I see here , thanks for sharing 🙏🔥💯🎣🚤👀
Great video! Thank you for sharing. I just bought a brand new Pelican bass raider10E from Cabela's. I have a lot of great things in the making for it but great to see others projects! Cheers!
Very nice set up I would like to get some of the transducer mounts you made let me know if it's still possible to get some and were did you get your t tracks at
Great video, an thank you for that. I did buy one today at academy sports, $749.00 Not bad. So it's still in the back of my truck, and I will be working on it today, and tomorrow. thanks guys/girls. have a great one
Love the usage of 3D printing! What filament do you use? I know PLA isn't great with heat or water, I've used PETG with some success but found it can warp under high heat. I'd love to avoid using ABS but it might be the only filament appropriate for outdoor use that's exposed to water.
I use PETG for the clamps and transducer mounts. Been using PLA+ with great success underwater. In some instances I've had better luck with PLA+ as it seems less brittle but less temp resistant.
nice mods, just curious which ones you would do again or not after using the boat for a year. also, what about the pelican seat over the cushioned one? thanks for the vid
If I were to build another one, there isn't much I'd change. I surely wouldn't use the plastic scupper plug again - lol. the Ergo 360 seats are much lighter and are mesh with breathe much better than a padded seat. No swamp-ass!
Hey Jeff really like your setup. Just got my bass raider and in process of setup. looked at a lot of different mods. I like your t track and the 3D parts. I would like to get those 3D mounts you made. let me know how to get my address to you. Thanks.
Hi Jeff, I love the mods you made to your boat! I have the same exact boat and I was wondering how you re-ran the wires through the hull? Did you just tie the new ones to the factory ones and simply pull them through? Also, is there any advantage to using 6 guage wire vs. the 8? Thanks.
Yeah, I just tied the new ones in and dragged them through. 6ga is whats needed for 50 to 60 amps. If you are running a smaller motor you will probably be fine but I have a 65 and 55lb thrust I run on mine.
@@jeffakamax Thanks for the reply Jeff. I thought the factory wires were kind of on the light side myself. I'm running a 55 lb. Minnkota so I think I'm going to do the same thing you did! I really like the Anderson plugs too I just have some basic 8-10 guage solderless connectors but one actually pulled out this weekend on me.
What 3d printer do you own and would recommend. Do you have a link and also when i get mine would you be willing to send me the files for it. These are some of the greatest mods i have seen. Thanks. Also what size drain plugs and size holes did you install in the bottom. Do you have a link to them please
How has the aquarium sealant held up. Thinking of doing the same to my angler 8s. Not sure what to use. I've seen people use flex seal and bed liner. Then I saw your video.
At the bow, what size schedule 40 PVC did you use for rod holders ? I bought 1&1/4 inch PVC but it doesn’t quite fit in the straps. My Bass Raider is new and the straps are quite stiff. Thanks in advance. Steve B.
Thanks so much for the suggestion. Before I forget, I was about to put in an Atwood scupper plug when I came across your video. How did you go about fixing the problem? If you had to do it 5:34 over, would you still go with a scupper plug? Thanks a million for getting back to me. I really enjoy the ideas you come up with.
www.amazon.com/gp/product/B007SXHKFU/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Have NO complaints on that motor at all! I cut the shaft down so it's shorter than usual. I like to be able to cast over it without it being in the way. Personal preference really. I also have a 65LB Haswing that is ESC controlled. Works great too but not good at FWD/REV prop cleaning to remove weeds.
Thank you for sharing, just curious i know you said you would 3d print the attachments for the transducer? but what about the sun sharde for the striker four, i let a buddy go out on my kayak and he knocked it off with the paddle :(
www.amazon.com/gp/product/B07ZV5R6CP/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 www.amazon.com/gp/product/B07YFNT3RY/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 www.amazon.com/gp/product/B00FUEN2GK/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 here you go!
I wish I had gotten this information about the Rubber seal before I took the one off my pond prowler, oh my gosh, same thing happened to me I had to stretch that thing
The use of the T track is ingenious. I’m not into woodworking so I’ve not heard of it . Definitely a future mod for my pelican . Thanks for sharing.
Highly recommended, they work great!
The BEST small boat mid video yet. Great logic, design and craftsmanship!
Thanks!
I'm Impressed . You did a great job fabricating everything . I'm getting one soon , I think I'll keep the trim on and just seal at the joints top and bottom . Love the Flag ! Thanks
I just picked mine up from Academy in Killeen Texas ,that and a Minn Kota 50lb thrust Endurance trolling motor for 579$ they loaded it up after I inspected it and 💥 bam I was on my way home. I’m so excited about the mods I see here , thanks for sharing 🙏🔥💯🎣🚤👀
that's a great deal!
Great video! Thank you for sharing. I just bought a brand new Pelican bass raider10E from Cabela's. I have a lot of great things in the making for it but great to see others projects! Cheers!
Nice setup! It’s clean, great job I threw a casting deck on mine, these little boats are great.
Really like what you have done to your boat! We are using a lot of your ideas. Thanks for making your video.
By the way I just bought my boat NEW paid 1,100.00 for it at bass pro😫
@@maryandersen3172 you'll enjoy it, they are great little boats.
Some great ideas. Thank you for sharing. Especially about the black trim.
I'd love one of the transceiver mounts. Very creative. 🙌🙌
email me at jeffakamax@gmail.com I'll hook you up
You are a trip. Great video man
Hello Jeff love everything you did with the bass raider how I'm very interested in the cart you built to move it around
Hey just found your videos. You still up for printing those transducer mounts?
sure am, email me at jeffakamax@gmail.com
Very nice set up I would like to get some of the transducer mounts you made let me know if it's still possible to get some and were did you get your t tracks at
T-tracks from Amazon. email me at jeffakamax@gmail.com and I can hook you up with the other parts.
Great video, an thank you for that. I did buy one today at academy sports, $749.00 Not bad. So it's still in the back of my truck, and I will be working on it today, and tomorrow.
thanks guys/girls. have a great one
You will love it, they are a blast!
Love the usage of 3D printing! What filament do you use? I know PLA isn't great with heat or water, I've used PETG with some success but found it can warp under high heat.
I'd love to avoid using ABS but it might be the only filament appropriate for outdoor use that's exposed to water.
I use PETG for the clamps and transducer mounts. Been using PLA+ with great success underwater. In some instances I've had better luck with PLA+ as it seems less brittle but less temp resistant.
I love your 3d printed pole holders! Did you make the file?
Can you make a video explaining the rewire? I just bought my first boat and want it wired this way
nice mods, just curious which ones you would do again or not after using the boat for a year. also, what about the pelican seat over the cushioned one? thanks for the vid
If I were to build another one, there isn't much I'd change. I surely wouldn't use the plastic scupper plug again - lol. the Ergo 360 seats are much lighter and are mesh with breathe much better than a padded seat. No swamp-ass!
Hey Jeff really like your setup. Just got my bass raider and in process of setup. looked at a lot of different mods. I like your t track and the 3D parts. I would like to get those 3D mounts you made. let me know how to get my address to you. Thanks.
email me at jeffakamax@gmail.com
Nice job, my friend. I love mine. Thanks🙏🏿🇺🇸
Jeff, would you be willing to share your guide files for your mods? Transducer holder, clamps and rod holders all look great!
Hi Jeff, I love the mods you made to your boat! I have the same exact boat and I was wondering how you re-ran the wires through the hull? Did you just tie the new ones to the factory ones and simply pull them through? Also, is there any advantage to using 6 guage wire vs. the 8? Thanks.
Yeah, I just tied the new ones in and dragged them through. 6ga is whats needed for 50 to 60 amps. If you are running a smaller motor you will probably be fine but I have a 65 and 55lb thrust I run on mine.
@@jeffakamax Thanks for the reply Jeff. I thought the factory wires were kind of on the light side myself. I'm running a 55 lb. Minnkota so I think I'm going to do the same thing you did! I really like the Anderson plugs too I just have some basic 8-10 guage solderless connectors but one actually pulled out this weekend on me.
@@paulbernardi2597 anderson connectors and some 6ga wire and you'll never have to worry about it.
I would like the 3 D transducer mount you have. Is that still possible?
email me at jeffakamax@gmail.com
Great video Jeff. How did you hook up the shock chords used in the trac? Are they pre built?
No I just made them up with an eyelet on each end and mounted to the track with a t stud and nut
How did you replace the original wiring? I just purchased the Pelican Bass Raider 10 e.
I tied off the new 6ga wiring to the existing OEM wire and used that to pull it through.
@@jeffakamax thanks
What 3d printer do you own and would recommend. Do you have a link and also when i get mine would you be willing to send me the files for it. These are some of the greatest mods i have seen. Thanks. Also what size drain plugs and size holes did you install in the bottom. Do you have a link to them please
Whats your budget for a printer? Check k my other videos for info on drain plus and supper plug.
500 or less
@@WiztekServices creality K1 or bambu p1p if you have a little more to spend.
@jeffakamax thanks it looks like the bambu p1p is better so i will order that one and thank you
Outstanding, I'll be watching! How did you bond the lattice to the hull?
3M VHB tape
How has the aquarium sealant held up. Thinking of doing the same to my angler 8s. Not sure what to use. I've seen people use flex seal and bed liner. Then I saw your video.
Flex seal is a joke. The RTV has held up well! (Aquarium sealant)
@@jeffakamax Thanks!
Great mods! What type of screws did you use to install those tracks? Are they stainless?
Yeah, stainless screws and VHB tape
Nice setup.
At the bow, what size schedule 40 PVC did you use for rod holders ? I bought 1&1/4 inch PVC but it doesn’t quite fit in the straps. My Bass Raider is new and the straps are quite stiff. Thanks in advance. Steve B.
If memory serves, it was 1 1/4. A little heat from a heat gun or hair dryer will soften things up just a bit if needed.
Thanks so much for the suggestion. Before I forget, I was about to put in an Atwood scupper plug when I came across your video. How did you go about fixing the problem? If you had to do it 5:34 over, would you still go with a scupper plug? Thanks a million for getting back to me. I really enjoy the ideas you come up with.
@@steveb.1701 I replaced it with a stainless steel supper, no problems after that
Smart. Thanks.
Jeff: Would you mind posting the link to the stainless steel scupper assembly?
Yes where did you get the rubber mat for the floor of the pelican
Was some wire raceway I had laying around. Just an industrial version of an anti fatigue mat.
Wow that’s some very cool upgrades, I just sent you an email.
What was the length of the trolling motor. I think you said it was a water snake. Who makes it? Thanks.
www.amazon.com/gp/product/B007SXHKFU/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Have NO complaints on that motor at all! I cut the shaft down so it's shorter than usual. I like to be able to cast over it without it being in the way. Personal preference really. I also have a 65LB Haswing that is ESC controlled. Works great too but not good at FWD/REV prop cleaning to remove weeds.
Thank you for sharing, just curious i know you said you would 3d print the attachments for the transducer? but what about the sun sharde for the striker four, i let a buddy go out on my kayak and he knocked it off with the paddle :(
email me at jeffakamax@gmail.com and I will print you one up
any way you can provide the .stl files? I would love to print some of your mods.
Where did you order the tape from that you put under your t track
Amazon. Scotch-Mount Double Sided Mounting Tape Heavy Duty, Black Extreme Mounting Tape
What size T track did you use? Does it work with RAILBLAZA EXPANDA Track Low Profile Kayak Accessories Mount Track
Just basic T track. www.amazon.com/gp/product/B07ZV5R6CP/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&th=1
Jeff in the beginning you said your battery was a 1000-amp hour battery, did you mean 100 amp hours? thank you kindly.
YES! 1000aH would need a bigger boat...lol
How did you glue the pvc strips on the bottom
@@robertnaughton5417 I used 3m vht
Hey Jeff. Where did you get your foam mat from?
Was some old cord raceway I had laying around
I'm steealing your t track idea. Any advice on where I could find a paddle bracket like that? Not having any luck.
Steal away! Got mine from amazon... search. Kayak Paddle Holder Clips(Including Screws),Deck Mounted Universal Kayak Paddle Clip & Fishing Net Clip
@@jeffakamaxsorry, I meant the metal bracket.
@@EricScherrer the bracket that mounts the paddle clip for the T track? Just something I bent up myself.
@@jeffakamaxI'll probably have to do the same. It usually comes out pretty bad when I do.
Hey Jeff, what did you use to apply the lattice? what adhesive?
Scotch-Mount Extreme Double sided tape. Same as 3M VHB but cheaper
thank you!
Wow this thing is Sweet! Where can I order one haha
Hey I'd like u to print up the transducer pole clamps and transducer mont if u can
email me at jeffakamax@gmail.com
Do you have links for the rails that are on the boat and I’d like a transducer arm
www.amazon.com/gp/product/B07ZV5R6CP/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Email me at jeffakamax@gmail.com for parts
Can you add the link for the rod holders and transducer holders?
Excellent video and suggestions ...but no need to go to 6 gauge wire for this application.
Oem wiring claimed to be 8ga but looked more like 10ga. 60amps through 10 feet is borderline. I had some 6ga laying around anyway.
What size clamps did you use for your rod holders?
2.5" if memory serves
can you add the link for the Transducer and other items? i have a 3d print farm. Thanks
I'll send you the file.
Jeff, fantastic build, I would appreciate the link as well.
what did you use as a glue keel guards ?
3m VHB tape
Great video. You are right these boats are hard to find.
Think you can 3d print me one?
Sure can. Email me at jeffakamax@gmail.com
I forget the manufacturer, but there is a company 3D printing entire boats!
I need one of them mounting just got me a pelican bass raider I’m a beginner angler and need some tips lol
Where did you get the track/screw/tape from?
www.amazon.com/gp/product/B07ZV5R6CP/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
www.amazon.com/gp/product/B07YFNT3RY/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
www.amazon.com/gp/product/B00FUEN2GK/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
here you go!
Would like to purchase the 3D parts for the transducer if available..
Email me at jeffakamax@gmail.com
What size screws did you use to attach the T tracks?
#7 5/8" stainless wood screws
I wish I had gotten this information about the Rubber seal before I took the one off my pond prowler, oh my gosh, same thing happened to me I had to stretch that thing
How long can you run your trolling motor on your lithium battery?
If I'm out for 4 to 6 hours, I rarely use more than 40%
Love your mod!!! I would really love a 3D clamp and arm if you don’t mind? I would even pay for it 😊
email me at jeffakamax@gmail.com and I'll hook you up
Hi Jeff...I would love to get the arm and clamp/mount as well. How do I get you to send to me?
email me at jeffakamax@gmail.com
Does anyone have the stereo foam layout for one of these boats?
What did ya adhere the pvc strips on the bottom with
The scotch version of 3m VHB
I’d love some of those 3d print fittings
You got it. Email me st jeffakamax@gmail.com
Could I get the STL files for the build?
Need some rod holders to
What sizes are your t tracks??
I bought 4 foot lengths and cut them accordingly.
@@jeffakamax Thanks i want to do this to my quest angler 10
Hi! I would love a 3D print of your version Scotty arm!
The arm is just pvc. Do you need the clamp and mount?
Hello, would you mind making me a 3D print of the transducer mount that you had in the video?
The adaptor for transducer to pvc?
I would need the clamps and the part for the transducer. That setup is extremely nice that you did.
@@tomspitzer8346 I'll print up a set and contact you for shipping info.
Sounds great! Thank you. What did you use to get the clamps to stay in the tracks?
@@tomspitzer8346 www.amazon.com/gp/product/B07GS3YS9R/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&th=1
Navigation, anchor and running lights!
I sent you a email bud. Im interested in those transducer clamps
lets seee more on this 1000 ah battery please
I have a few eco-worthy 100ah batteries. Going on their 3rd season in 3 different boats.
Id like a set of the clamps and adapter..sent you email thanks