ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
Reinforcement lapping zone in Beams | Basic rule for lapping length in beams | Civil Tutor
ฝัง
- เผยแพร่เมื่อ 10 ธ.ค. 2021
- In this lecture I have discussed briefly, what should be the reinforcement lapping zone in beams and the basic rule for lapping length in beams.
Download our android app for job oriented courses
clpsheldon.pag...
quantity surveying topics compiled PDFs 👇🏻👇🏻
store.civiltuto...
SFD & BMD PDF
store.civiltuto...
2nd channel 👇🏻
/ civiltutorofficial
As I have already told you, If the span of a structural member needs to be increased beyond the standard length (12m) of the reinforcement bar, then we must increase the length of bars by adding extra steel bars. The most important thing, we can’t add the bars directly from end to end to avoid the risk of steel sliding out of concrete. That’s why we overlap the bars at certain points to allow a smooth transfer of loads from one bar to the next.
In this lecture, I’m going to discuss what should be the position of the lap in the case of beams. Before deciding the lapping zone of a beam, we need to identify the points where a member is subjected to a maximum bending moment, or simply, we need to identify the tension zones of a beam. For illustration, let’s consider a continuous beam that is subjected to a uniformly distributed load. Due to this loading, the beam will tend to bend in a way that the maximum bending moments will be generated at the center of the spans. There will be positive moments at the center of the spans and negative moments at each support. Due to the maximum bending moment, the top fiber of the beam at each end and the bottom fiber in the mid-span will experience maximum tension. Hence, they can be called tension zones of the beam and we can’t overlap the bars in tension zones because the reinforcement bars would come out of the concrete due to maximum stress.
For bottom bars, we can’t overlap the bars at the mid-span of the beam due to maximum tension in the bottom fiber of the beam. On the other hand, the top bars can be overlapped in the mid-span of the beam due to minimum tension in the top fiber of the mid-span. If we divide the span into three equal parts, the overlapping of top bars should be done in the intermediate zones and each bar should be overlapped at alternative levels within the lapping zones.
The bottom bars should be overlapped at column junctions up to a distance of L/4 from each end and each bar should be overlapped at alternative levels within the lapping zones.
Note: Not more than 50% of the bottom bars in a beam are overlapped in the same zone plus columns of any clear span.
#bbs #civiltutor #quantitysurveying #ermuyeenmubarak #civilengineer
Civil engineering animations Playlist 👇🏻
• Civil Engineering anim...
Strength of materials Playlist 👇🏻
• Shear force and Bendin...
How to calculate the quantity of cement and sand for plastering work 👇🏻
• How to calculate quant...
What is 1.54 in concrete? 👇🏻
• What is 1.54 in concre...
How to calculate the volume of a cement bag? 👇🏻
• How to calculate volum...
AAC BLOCKS VS RED BRICKS 👇🏻
• AAC Block vs Bricks | ...
Difference between one-way slab and two-way slab 👇🏻
• What is One way slab t...
What is development length? 👇🏻
• What is development le...
Why do we provide cranked Bars?
• WHY CRANK BARS ARE PRO...
Basic knowledge for civil engineers 👇🏻
• Part 1 | Basic knowled...
Derivation of D²/162
• Derivation of D²/162 |...
Compiled pdfs👇🏻
quantity surveying topics compiled PDFs 👇🏻👇🏻
store.civiltutorofficial.com/
SFD & BMD PDF
store.civiltutorofficial.com/product/shear-force-and-bending-moment/
2nd channel 👇🏻
th-cam.com/users/Civiltutorofficial
some say we should avoid lapping at the column juction joint and some are say we can do it , but according to IS13920 1993 CL.6.2.6 , we should avoid lapping within the joint and within a distance of 2d from the support,
In bottom portion 2d ?
Thank you will keep listening nd watching your channel ..merry X'mas
Namaskaram, nice explanation...
Sir, you deserve million views and subscribers ❤
Thank you so much
Thanks for this information.
If top bars don't get lap zones bcoz of span is more for continuous beams
For bottom, lapping is provided by avoiding center not in volumn joint.
Please explain the bbs of plinth beam main bars
Ples tell lap length in teams of bar diameter for beam
Talk about stirrup spacing. Some use equal spacing while others use more spacing in the middle of the beam
The purpose of stirrups is to hold the main bars in position and to counter the effect of shear force. Since the shear is maximum near the supports and gradually decreases towards the centre of the beam and becomes zero at the centre. That's why stirrups are provided with closer spacing near the supports in comparison to the intermediate span.
Thankyou..
Thanks
great video
Glad you enjoyed it
Sir layout ka video banana ha
Briefed