@@slownlowdetectingwith the increased target id range on the 900 would t1 on the advaned still be noisy as the rid range increased from 40 to 99. So setting this t1 at 2 or 3 be more applicable?
Hi many thanks for the settings info. I just bought my Nox this week and was a little lost as to set up a quiet programme. Thanks to your direction it worked a treat and found my first silver for the Nox a lovely George lll sixpence 1818. Many thanks once again for your great work
Hello again Neil, just want to say about this settings of yours, it's fantastic I have followed other TH-camrs settings without much confidence, but this settings blew my mind up' went back to my old hunting ground found 4 - 925 silver rings and, $13 spend able coins I thought that Park was all hunted out wow wow thank you again bro' take care out there and a happy hunting
Thanks Rima and thanks also for your kind words 😊 keep me updated and show your finds results on DUG THAT'S OFFICIAL MINELAB EQUINOX 800-600 GROUP on Facebook 👍
great iron set up. that single increment of Tone Break is a great stabilizer-- I use it in the salt, it lets you run more gain if you want although 19 is a great way to hear your targets better--it offsets all the modulation. thanks for clarifying Neil-- there are a lot of half baked versions floating around.
I’d just like to say that, even though I’ve had my Nox for three years, these are still the best settings (although I use 2 tones instead of 50 - I just can’t get on with 50 on any of the modes). I used your settings before the 2nd update came out and I always wondered what the F2 setting should be. Now I know. Thank you.
Thanks Lesley 👍 I know it can be hard but it is very advantageous to use multi tones, there are ways to improve your finds rate and they all combine together to do it. Multi tones is just one of them, turn your volume down so its not to much for you and annoying and slow your swing right down as it makes things less messy.
Hi Neil, thanks for the settings they work great. You mentioned at the start of the video that you were going to provide some "Expert, heavy hot settings " later. Please can you advise these settings. Regards
Just a case of upping sensitivity, lower recovery etc and concentrate on you swing technique, try not to hover and scrape surface lightly. Where your coil cover out 😀
Hi George, I use it as hot as it can go all the time but you need to learn the machine like the back of your hand and swing correctly too plus low headphone volume as its not for the faint hearted and takes a hell of a lot of getting used to 👍
Hello mate, First off what a video you have put together here mate I have just programmed my new 900 I have a few questions though. I don’t seem to be able to find the 50 tones option do you know why this is ? I have applied this setting to beach and saved it does it save all the setting in this way as in field 1 will now be set to this ? Thanks for your help mate
@@slownlowdetectingone last question mate I dont have the f2 option in the menu what should I set the fe to 1? And do I just leave it on beach one when detecting on fields etc. Thanks Thanks so much again Shane
Yes of course, but instead of 50 tones its AT and theres no F2 its just FE. The best thing about the 900 is 3 extra incriments of sensitivity but most wont use tbem 👍
I’m new to the nox 800, how does this fair against field 2 ? I know a few who have never used anything but field 2 but I’m not clued up as to why this beach setting would be better
Sorry for late late reply, field 2 favours small finds in bad iron, its not as deep as the other modes if you want depth too. Beach 1 setting is a fab arounder, brill in heavy iron with brilliant separation, brill depth, very powerful with the bonus of being stable too 👍
thanks for the wonderful program mate! used it for the first time its awesome..I'm curious about a couple things..should I see that user profile icon everytime I switch into beach 1? I noticed yours stayed on..and also i put mine in all metal before I saved but after turning it off and back on I had to hit all metal again..just wondering if that's normal thanks!
Hi Derek sorry I'm late, every time you switch on you need to press the horseshoe button, what ever user profile you used when detecting will be there when you next switch on 👍
Hi Neil, Due to this custom mode programme i'm assuming it works equally well on beaches, or do I need to select a beach mode and just use this custom mode on land? Cheers buddy, thanks for uploading, as easy to follow.👍
Neil, I entered all the settings with 5 tones set, today I entered 50 tones, now it’s not showing tone break adjustments or tone volume adjusts. When I revert back to 5 tones the tone breaks all reappear. Any thoughts?
Default settings are just for people to get used to the machine. F2 at zero gives more tonal information and makes iron easier to recognise and more non ferrous signals stand out.
Thank you so much for the information on the nox 900 Neil the beach to land settings appreciated happy hunting
Same as 800 but instead of 50 tones its AT (all tones) and there is no F2 its FE just put that at zero 😊
@slownlowdetecting Thank-you so much, Neil happy hunting
@@slownlowdetectingwith the increased target id range on the 900 would t1 on the advaned still be noisy as the rid range increased from 40 to 99. So setting this t1 at 2 or 3 be more applicable?
Hi many thanks for the settings info. I just bought my Nox this week and was a little lost as to set up a quiet programme. Thanks to your direction it worked a treat and found my first silver for the Nox a lovely George lll sixpence 1818. Many thanks once again for your great work
Nice one that's brilliant and thanks very much for the great feedback 😀
Hello again Neil, just want to say about this settings of yours, it's fantastic I have followed other TH-camrs settings without much confidence, but this settings blew my mind up' went back to my old hunting ground found 4 - 925 silver rings and, $13 spend able coins I thought that Park was all hunted out wow wow thank you again bro' take care out there and a happy hunting
Thanks Rima and thanks also for your kind words 😊 keep me updated and show your finds results on DUG THAT'S OFFICIAL MINELAB EQUINOX 800-600 GROUP on Facebook 👍
I recently found this video and am finding things in some pasture I have done to death. Awesome settings. Thanks Neil
Nice one bud and thanks 😀
Brilliant. You set mum's machine up at detectival, and she's still using it now. Hope you're keeping well. 😁
Nice one thanks Griff 👍
Loving the beach to land settings found lots today thanks for that
Thanks 😊
Hi Neil Used your settings for the first time and hit double silver on the pasture queen Ann sixpence 1711 and bull head sixpence 1816 great start 👍
That'sa fab start very well done indeed 😀
great iron set up. that single increment of Tone Break is a great stabilizer-- I use it in the salt, it lets you run more gain if you want although 19 is a great way to hear your targets better--it offsets all the modulation. thanks for clarifying Neil-- there are a lot of half baked versions floating around.
Thanks Clive 👍
@@slownlowdetecting thank you for this awesome program for equinox...really performing and stable...good hunt
I’d just like to say that, even though I’ve had my Nox for three years, these are still the best settings (although I use 2 tones instead of 50 - I just can’t get on with 50 on any of the modes). I used your settings before the 2nd update came out and I always wondered what the F2 setting should be. Now I know. Thank you.
Thanks Lesley 👍 I know it can be hard but it is very advantageous to use multi tones, there are ways to improve your finds rate and they all combine together to do it.
Multi tones is just one of them, turn your volume down so its not to much for you and annoying and slow your swing right down as it makes things less messy.
Thanks will try this on Wednesday when I’m next on land.
Good luck 🍀
Hi Neil, thanks for the settings they work great. You mentioned at the start of the video that you were going to provide some "Expert, heavy hot settings " later. Please can you advise these settings. Regards
Just a case of upping sensitivity, lower recovery etc and concentrate on you swing technique, try not to hover and scrape surface lightly.
Where your coil cover out 😀
Hiya Neil any chance of doing a video for the 900 settings or explaining how to set it up cheers.
Hi Darren, its the same as 800 and 600, except 50 tones which wasn't 50 tones is now AT as in all tones, and iron bias is only FE now, there is no F2.
Cheers Neil and thanks for the explanation much appreciated thanks.
@@darrensutton9387your welcome 👍
good to at last see you made a video this will help a lot of people
Thanks Gerry 👍
Only settings I use cheers Neil for tweaking them to suit me :)
Cheers me lovely 👍
Thank you from south Texas.
Your welcome 👍
Hi Neil, what is the hot advanced settings and when would you use these over the tame settings? Thank you
Hi George, I use it as hot as it can go all the time but you need to learn the machine like the back of your hand and swing correctly too plus low headphone volume as its not for the faint hearted and takes a hell of a lot of getting used to 👍
Is this good for pasture and ploughing
Yes sure is 👍
Merci et bonne année 2024
Cheers bud 👍 😊
Hi Neil is it OK if I use 5 tones instead of 50 tones thanks
Yes of course, but as I say 50 is just a smoother rounded version of 5 so don't worry about the number 50.
Thank you very much for your reply Bro' take care out there and a happy hunting
Why do I have an exclamation mark on the upper leftside next to the battery indicator in beach mode?
Usually a large target, is it in your home.
@@slownlowdetecting was setting up your program
Does this work on the equinox 600?
Hello mate,
First off what a video you have put together here mate I have just programmed my new 900 I have a few questions though.
I don’t seem to be able to find the 50 tones option do you know why this is ?
I have applied this setting to beach and saved it does it save all the setting in this way as in field 1 will now be set to this ?
Thanks for your help mate
Hello, yes it will save ine beach 1 when you go to it.
Just set it to all tones as it just doesn't say 50 anymore.
@@slownlowdetectingone last question mate I dont have the f2 option in the menu what should I set the fe to 1? And do I just leave it on beach one when detecting on fields etc.
Thanks
Thanks so much again
Shane
@@shanea2045 just put Fe on 0 and leave on beach 1 yes.
@@slownlowdetecting thanks so much mate if I ever see you about I owe you a beer.
Cheers pal
Has anyone put these settings in to the nox 900 or do you need to tweak it up ?
Just same as 800 but AT instead of 50 tones, iron bias FE at zero,.
Bonjour neil le programme plage à la terre et t il le même pour l equinox 900 ?
Yes but instead of 50 tones its AT and theres no F2 so FE 0.
Mensionaste una configuracion para profesionales ,donde se puede ver, gracias.
Cheers ❤❤ 🍻🍻
Have you done a beach to land for the 900, is there one out there
Just follow the settings as before bud.
Hi Neil,would this work just as well on the 900 with a 15" coiltek please?
Yes of course, but instead of 50 tones its AT and theres no F2 its just FE.
The best thing about the 900 is 3 extra incriments of sensitivity but most wont use tbem 👍
I’m new to the nox 800, how does this fair against field 2 ? I know a few who have never used anything but field 2 but I’m not clued up as to why this beach setting would be better
Sorry for late late reply, field 2 favours small finds in bad iron, its not as deep as the other modes if you want depth too.
Beach 1 setting is a fab arounder, brill in heavy iron with brilliant separation, brill depth, very powerful with the bonus of being stable too 👍
Will these settings work the same for the 900
Yes just use AT instead of 50 tones and iron bias fe on zero.
Hey Neil it's beach to land is that the same weather it's wet sand or dry sand
Yes no different, if you go in seawater change over to beach 2.
@@slownlowdetecting do you use the same setting in beach 2?
thanks for the wonderful program mate! used it for the first time its awesome..I'm curious about a couple things..should I see that user profile icon everytime I switch into beach 1? I noticed yours stayed on..and also i put mine in all metal before I saved but after turning it off and back on I had to hit all metal again..just wondering if that's normal thanks!
Hi Derek sorry I'm late, every time you switch on you need to press the horseshoe button, what ever user profile you used when detecting will be there when you next switch on 👍
Hi m8, will these settings work on the new 900? Thanks
Yes Lee they sure will 👍
Hi Neil 👋 is this set up better than the recovery addict beach to land thanks bro 👍
I devised this setting while testing the machine for Minelab 👍
Con esta configuración es como si tubiera otro detector, gracias.
Nice one that's brilliant and thanks for the comment, sorry for the late reply too 🙏
Hi Neil,
Due to this custom mode programme i'm assuming it works equally well on beaches, or do I need to select a beach mode and just use this custom mode on land? Cheers buddy, thanks for uploading, as easy to follow.👍
Yes of course 👍
Hola muy buen vídeo. Tendrás configuración para parque?
This is brilliant for parks 👍
@@slownlowdetecting lo voy a probar. Te contaré los resultados. Saludos.
Hi. Would these settings work on the new 900 machine too?
Yes Andrew of course 👍
Neil, I entered all the settings with 5 tones set, today I entered 50 tones, now it’s not showing tone break adjustments or tone volume adjusts. When I revert back to 5 tones the tone breaks all reappear. Any thoughts?
I don't understand what you mean 🤔
What happens if you use these settings without the latest update?
It won't be as stable.
@@slownlowdetecting Did the update and tried these settings today on my roman field. Very good indeed. 6 roman coins and a George 1st penny 👍
@@MrDogtown22 nice one we'll done 👍
Thanks for the settings going go give it a try Tommorow do you run your sensitivity on max 25?
Your welcome Mikey, put your sense on 23, I have mine on 24 - 25 but I'm mad 😂
Ok thanks also if I want to use 5 tones? Do u just change each section to 20?
Because with 5 tones in each section you have to choose a number
And with 50 tones it's just 1 section "20" if this makes sense
So if I set t2 to 20 what would I set t3 t4 and t5 too? Thanks for your help
thanks i putt them i but now correct
Nice one 👍
Any link for the 600 settings please
Just putting 600 video right now Kudzi 👍
@@slownlowdetecting thqnk you i will keep an eye 🙏
Neil why do you suggest a setting in F2 of Zero when default setting is 6 that is a big difference
Default settings are just for people to get used to the machine.
F2 at zero gives more tonal information and makes iron easier to recognise and more non ferrous signals stand out.
Can you put a link up for the updates 😀
If I can find them 😂??
Lo estoy usando en tierra, en agua salada pienso que sera igual.
It is yes 👍
Forgive my stupidity, but you use this setting on farm fields also?
Yes Jason
IS that the 800 or 600
800 😊
Mahallo
Everywhere 👍
Neil you can't be put in the settings on without doing the penguin luke 🤣🤣
Ya twonk 😂🤣