Hello. I wired the brights on the 6s to it own switch, the brights on the 4s to its own switch. All 4 light low power are one one switch. All 4 lights Amber are on one switch. Using a total of 4 switchs on my switch panel.
So you ran all the low power to one switch and the high power to two additional switches plus the marker light to a 4th switch. I know the manual says not to power high and low at the same time. If I have no interest in having low power I can just wire my 4 edge 4’s to either a single 40 amp harness and the marker lights to another switch panel right? But I guess if I have to use a relay I might as well do the low/high switch 🤔
I would suggest s switch panel. Cleaner and easier. But yes. I had to use 4 switches all together. All 4 lows on one switch. All 4 yellow back lights on one switch. 1 set of the 6 high on one switch and one set of the 4 high on one switch
I would use a switch panal. But I did use 4 spots on my switch panel. All 4 lights low on one switch. All 4 yellow back lights on one switch. Two 6 high on one switch and two 4 high on one switch
How did you mount the 4s to those mounts? Did you just use a smaller bolt? Update... I just bought M10 bolts and they fit - the bolt head doesn't lock in the mount like an m12 bolt
I just used the center (I think M12) bolt. I had to open the mount a tad bit with a step bit. Length was perfect. I cut one down a little thinking it would be to long but, but it was perfect. If I remember correctly I used lock nut with no washers. @garzilla2k480
CLEANNNN! 👍
Swap out the edge four for the edge six!
I have both
Hi Mike, so you wired your 6’s to one switch and the 4’s to another right ? And you only wired the pin4 high beam wire right.not the low beam?
Hello. I wired the brights on the 6s to it own switch, the brights on the 4s to its own switch. All 4 light low power are one one switch. All 4 lights Amber are on one switch. Using a total of 4 switchs on my switch panel.
@@mikephilpot9214 thanks!!! I’m going to give that a try this weekend. You just split the one ground from the light onto the 4 switch panel locations?
@@CarlosTorres-cx1pw I split the powers. I ran the grounds to one of the ground studs under the hood. Jeep has them all around.
So you ran all the low power to one switch and the high power to two additional switches plus the marker light to a 4th switch. I know the manual says not to power high and low at the same time. If I have no interest in having low power I can just wire my 4 edge 4’s to either a single 40 amp harness and the marker lights to another switch panel right? But I guess if I have to use a relay I might as well do the low/high switch 🤔
I would suggest s switch panel. Cleaner and easier. But yes. I had to use 4 switches all together. All 4 lows on one switch. All 4 yellow back lights on one switch. 1 set of the 6 high on one switch and one set of the 4 high on one switch
I would use a switch panal. But I did use 4 spots on my switch panel. All 4 lights low on one switch. All 4 yellow back lights on one switch. Two 6 high on one switch and two 4 high on one switch
How did you mount the 4s to those mounts? Did you just use a smaller bolt?
Update...
I just bought M10 bolts and they fit - the bolt head doesn't lock in the mount like an m12 bolt
I just used the center (I think M12) bolt. I had to open the mount a tad bit with a step bit. Length was perfect. I cut one down a little thinking it would be to long but, but it was perfect. If I remember correctly I used lock nut with no washers. @garzilla2k480
Can i use the Edge six as a ditch light or is it too big for that?
@@patriotsleepercell4060 IMO to big. Bit you can if you want. The Edge 4 would be plenty