My radio wasn’t flashed and I have a DSP I thought the change was because he tuned it at 12V without the bike running, but once I start it, it’s at 13.5-14V. What you mentioned actually makes sense sort of like the speed volume which i have turned off.
Your one of the few who point out how Harley changes the Frequencies when the Bike is running. I am running Biketronics Amp & LL's on a used bike (last 3 years). 2016 RG, GT stereo, that HAD a ArcAudio Amp. I suspect it wasn't flashed (learning curve, Arc didn't require flash ?) I rented a FLASH device from Biketronics and thought I got a 2x8 (?) Flash, or a common flash for added amps. Note FADE is available on the Radio. QUESTION: Rich Bass Sounds.....when I start the bike, it reverts to mids and highs, pretty bright, loose bass. WOULD that indicate MY Flash "didn't take" or I just flashed it back to Stock ?? After you flashed in this Video you showed the Flat Curve. Is it the SAME Flat curve with the bike running or off ?
Yes curve stays the same while engine is running after flashing to the 6 speaker 2 amp flash we show in this video, you can check your current flash by pulling the eq.bin number in the radio service menu, the flash we use is 134.bin
Great Video! I am running the GTS radio with the only the Boom Stage II fairing speakers and only the (1) Boom amp in the fairing. Would you use the same (2) amp flash for this set up?
@@volunteeraudio Thanks for the fast reply! I am planning on keeping the stock Boom Amp and Speakers. I just upgraded to the GTS radio from a 6.5GT so I was hoping to have it flashed it so it sounds the best it can at all volumes without the crazy EQ curve. Unfortunately it appears that the Boom II cannot be flashed and I am stuck with the EQ settings unless i upgrade everything. Is this correct? Thanks again for all the videos!
Ive got a road glide standard with the 4.3 Radio. Im adding an amp leveraging the two fairing outputs (left/right) to go into a 2 to 4 line converter and then into the Amp (4 ch). Would I need to flash this unit? Not looking to use the rear fader or anything like that.
I have a 2017 SG CVO with the stock boom 2, 2 amp and 4 speaker setup. I thought that setup changes the curve upon startup? If so what do I need to have flashed?
on my GTS, I had HD Dealer flash to a Rockford Fosgate output/equalization (have small Cicada fairing amp with load resistors, and two fairing and two bag 6x9 speakers, with no dsp).. If we ran the white noise input, what would the output look like, and the eq curve change when the bike is running?
@@volunteeraudio well at least I got the right one (?) While there..what would be the recommended next fix? I did notice my Radio level into the amp is still higher than USB mp3 tracks and Bluetooth cell tube play backs..i have cicada 6.5 upfront, and infinity perfect 6×9 in bags
I don't want to add an amp but I'd like to do away with the EQ change on my stock Boom system when the bike (2017 FLHTK) is running. Can I do just that? Who do I contact to get it done?
@@volunteeraudio Thank you for your prompt reply. I have gone with two speakers no amp flash as the 4 speakers are wired parallel on the 2channel amp. No DSP either.
Great video. For a Rockford setup with front fairing and rear bag speakers and one TM400Xad amp would I use the 4 Speakers - Upper Fairing - Saddlebag - 1 Amp flash? Does this curve perform the same as the 2 amp one you used in the video. Thanks
No you always use the flash suggested in the video, it does not matter how many amps or speakers you are actually using, the radio can not tell what you are doing but selecting this flash gives the best radio eq setting for aftermarket amp
@@buzzbrischler5855 no, anytime you flash the radio correctly you are selecting a factory amplifier flash, all factory amps fade digitally to you will see fader but it will not work
Is having the Harley dealer flash it the same as getting the flashing device from you guys? Also can I install the system first and ride it to my local dealer and then have them flash it?
I have a Rockford Fosgate 4 speaker set up installed on my 20 RGS and the sound does change when the bike is off compared to when its running. The radio was flashed with the rockford flash and was wondering if the flash you use is better or should i leave it alone? P.S. I plan on installing the Rockford sub kit in the future .
The Rockford system recommends the Rockford flash, my opinion is that there are better flashes but you would need to retune the amplifier settings, if you are using hd audio by Rockford you need to use the suggested flash
This video is above my pay grade, my questions are probably pretty basic. I purchased a 2008 Street Glide with a OEM Harmon Kardon radio and it has the OEM 2 ohm front speakers only on the fairing, nothing is boom I believe, don't even know what boom is, should I even care, was boom even a thing back then? Anyway real my first question is this, my bike has the correct overlay and rear speaker harnesses for rear speakers and I want to install the speaker pods on the tour pak. How does the HD dealer flash the radio to activate the rear speakers? I have the ECM/ECU printout about my bike and it says the radio is configured for "2 speakers with or without boom amp-enhanced EQ". Will the dealer flash the radio with a CD in the radio CD slot in conjunction with connecting the bike to their digital technician? Second question is this, I'm being told by all the old timers that Harley will not be able to flash my bike because it is too old, that HD does not have software for a bike older than 10 years because that's as far back as they go?
Thank you for the quick reply but I'm not willing to purchase new audio equipment. If my AM/FM/XM/CD radio were broken I would consider your option, I kind of thought the answer to my question might be some sort of lead on how to obtain a technoresearch flash for OEM equipment not purchase new stuff. @@volunteeraudio
Also have the same issue on a 2008 electra glide. Front speakers only. Where did you find your harness for rears? I dont see any under my seat and want to hook up rear speakers
Wow, alot of info. I have a GTS in my 2017 SGS and running the hertz neo speakers with tweeters in grils, SD 400.4Evox and biketronics line level, will flashing my radio help at all?
@Volunteer Audio might need to call yall or see if my local HD can help. I know AAHD doesn't like to mess with aftermarket stereos. Thanks for the advice.
Your amp is too small, we can get you setup with a plug n play amp with correct power for your speakers and rent you the tool to flash the radio as well, reach out to our sales team @ 1-844-30AUDIO
another great video Jay. one question though. i have the older GT6.5 unit. does it operate the same as the GTS in that once started it re-sets the curve? i should have the dealer flash my radio to a boom 2 amp setting and get rid of my BT35 that i originally installed....which by the way was long before i found your videos
I got a used 2018 road glide special, it has Rockford front speakers and soundigital 4ch amp, the Treble is so aggressive it hurts my ears, can't get it up very high.. I have no idea if it was flashed or not. Any recommendations for a place in DFW, Texas?
My local shop flashed my 2018 street glide with the 2 speaker no amp flash and said it would level things out. Is this flash ok or should I have him reflash. I am installing 4 speakers 1 amp. Thanks
I have hertz neo speakers and a ordered the precision power 800w plug and play kit for my street glide from you guys for stock radio is it going to sound better than stock or should I be looking to send it somewhere to flash it to make a difference. ?
@@volunteeraudio ok so I’ll take those directions to a shop Or will it be cheaper to buy the part and do it myself the ones on your website are for 2014 and up I need for older 2009.
I sure do wish you were coming set up a booth at the Lone Star Rally down in Galveston, TX.
Perfectly explained Jay. Well done as always. Thanks for these! God Bless!!👋😇👍
My radio wasn’t flashed and I have a DSP I thought the change was because he tuned it at 12V without the bike running, but once I start it, it’s at 13.5-14V. What you mentioned actually makes sense sort of like the speed volume which i have turned off.
This is a very common problem, thank you for watching!
Your one of the few who point out how Harley changes the Frequencies when the Bike is running.
I am running Biketronics Amp & LL's on a used bike (last 3 years). 2016 RG, GT stereo, that HAD a ArcAudio Amp.
I suspect it wasn't flashed (learning curve, Arc didn't require flash ?) I rented a FLASH device from Biketronics
and thought I got a 2x8 (?) Flash, or a common flash for added amps. Note FADE is available on the Radio.
QUESTION: Rich Bass Sounds.....when I start the bike, it reverts to mids and highs, pretty bright, loose bass.
WOULD that indicate MY Flash "didn't take" or I just flashed it back to Stock ??
After you flashed in this Video you showed the Flat Curve. Is it the SAME Flat curve with the bike running or off ?
Yes curve stays the same while engine is running after flashing to the 6 speaker 2 amp flash we show in this video, you can check your current flash by pulling the eq.bin number in the radio service menu, the flash we use is 134.bin
When do you plan on posting a video on how to flash the radio?
Tomorrow
Great Video! I am running the GTS radio with the only the Boom Stage II fairing speakers and only the (1) Boom amp in the fairing. Would you use the same (2) amp flash for this set up?
If replacing your stock amp with an aftermarket one yes
@@volunteeraudio Thanks for the fast reply! I am planning on keeping the stock Boom Amp and Speakers. I just upgraded to the GTS radio from a 6.5GT so I was hoping to have it flashed it so it sounds the best it can at all volumes without the crazy EQ curve. Unfortunately it appears that the Boom II cannot be flashed and I am stuck with the EQ settings unless i upgrade everything. Is this correct? Thanks again for all the videos!
Ive got a road glide standard with the 4.3 Radio. Im adding an amp leveraging the two fairing outputs (left/right) to go into a 2 to 4 line converter and then into the Amp (4 ch). Would I need to flash this unit? Not looking to use the rear fader or anything like that.
Yes any time you add an amplifier we recommend flashing the radio for the reasons outlined in this video
If I already have the Harley Boom 2 amp setup on my bike does it really need to be flashed then when upgrading to an aftermarket amp and speakers?
Yes it does, you need a factory boom 1 6 speaker flash
I have a 2017 SG CVO with the stock boom 2, 2 amp and 4 speaker setup. I thought that setup changes the curve upon startup? If so what do I need to have flashed?
We flash to a specific 6 speaker 2 amp boom 1 flash that fixes these issues
@@volunteeraudio thanks. Am I able to flash it myself buying the flash file from you or need to bring the bike. I’m a ways away in the “mitten” state
@@briannathan9162 we rent the flash tool
on my GTS, I had HD Dealer flash to a Rockford Fosgate output/equalization (have small Cicada fairing amp with load resistors, and two fairing and two bag 6x9 speakers, with no dsp).. If we ran the white noise input, what would the output look like, and the eq curve change when the bike is running?
Terrible flash, all the dealer can do but still wrong
@@volunteeraudio well at least I got the right one (?) While there..what would be the recommended next fix? I did notice my Radio level into the amp is still higher than USB mp3 tracks and Bluetooth cell tube play backs..i have cicada 6.5 upfront, and infinity perfect 6×9 in bags
I'm installing 4 -6.5 Hertz speakers, 4-DSL 8"loud speakers & 2 amps. Wanting to keep stock radio on 2014 Harley ultra limited. Will flashing work?
You always need to flash the stock radio when adding amplifiers
I don't want to add an amp but I'd like to do away with the EQ change on my stock Boom system when the bike (2017 FLHTK) is running. Can I do just that? Who do I contact to get it done?
No, if you flash the radio it lowers output for adding an amp, without an amp you will not be able to hear your speakers
Hi thank you for your video and explaining the use of the DSP. Would you use the same flash if you have a single 2 channel amp with 4 speakers?
We normally do not use a dsp, and yes this is the flash we use every time we add an amp to a Harley
@@volunteeraudio Thank you for your prompt reply. I have gone with two speakers no amp flash as the 4 speakers are wired parallel on the 2channel amp. No DSP either.
@@kennedybeaton9110 you are using the stock flash that has the bad eq issues
@@volunteeraudio thank you for your reply. So to get the correct Flash i require the Techno Research Tuner?
Great video. For a Rockford setup with front fairing and rear bag speakers and one TM400Xad amp would I use the 4 Speakers - Upper Fairing - Saddlebag - 1 Amp flash? Does this curve perform the same as the 2 amp one you used in the video. Thanks
No you always use the flash suggested in the video, it does not matter how many amps or speakers you are actually using, the radio can not tell what you are doing but selecting this flash gives the best radio eq setting for aftermarket amp
@@volunteeraudio Thank you. One last question if you don't mind. Will this allow front/rear fade? Again really appreciate your videos.
@@buzzbrischler5855 no, anytime you flash the radio correctly you are selecting a factory amplifier flash, all factory amps fade digitally to you will see fader but it will not work
@@volunteeraudio Thanks for the explanation. I'll give the flash a try.
Is having the Harley dealer flash it the same as getting the flashing device from you guys? Also can I install the system first and ride it to my local dealer and then have them flash it?
The Harley dealer can not flash the radio like we show here. Only a technoresearch flash tool can do it
I have a Rockford Fosgate 4 speaker set up installed on my 20 RGS and the sound does change when the bike is off compared to when its running. The radio was flashed with the rockford flash and was wondering if the flash you use is better or should i leave it alone? P.S. I plan on installing the Rockford sub kit in the future .
The Rockford system recommends the Rockford flash, my opinion is that there are better flashes but you would need to retune the amplifier settings, if you are using hd audio by Rockford you need to use the suggested flash
This video is above my pay grade, my questions are probably pretty basic. I purchased a 2008 Street Glide with a OEM Harmon Kardon radio and it has the OEM 2 ohm front speakers only on the fairing, nothing is boom I believe, don't even know what boom is, should I even care, was boom even a thing back then?
Anyway real my first question is this, my bike has the correct overlay and rear speaker harnesses for rear speakers and I want to install the speaker pods on the tour pak. How does the HD dealer flash the radio to activate the rear speakers? I have the ECM/ECU printout about my bike and it says the radio is configured for "2 speakers with or without boom amp-enhanced EQ". Will the dealer flash the radio with a CD in the radio CD slot in conjunction with connecting the bike to their digital technician? Second question is this, I'm being told by all the old timers that Harley will not be able to flash my bike because it is too old, that HD does not have software for a bike older than 10 years because that's as far back as they go?
I would highly suggest upgrading your radio on a 2008 model, give us a call to go over pricing and options at 1-844-30AUDIO
Thank you for the quick reply but I'm not willing to purchase new audio equipment. If my AM/FM/XM/CD radio were broken I would consider your option, I kind of thought the answer to my question might be some sort of lead on how to obtain a technoresearch flash for OEM equipment not purchase new stuff. @@volunteeraudio
Also have the same issue on a 2008 electra glide. Front speakers only. Where did you find your harness for rears? I dont see any under my seat and want to hook up rear speakers
Wow, alot of info. I have a GTS in my 2017 SGS and running the hertz neo speakers with tweeters in grils, SD 400.4Evox and biketronics line level, will flashing my radio help at all?
Yes, line leveler is the worst way to connect an amp to a Harley, then reset your gains for the new input signal
@Volunteer Audio might need to call yall or see if my local HD can help. I know AAHD doesn't like to mess with aftermarket stereos. Thanks for the advice.
@@jasonbreedlove495 the Harley dealer cannot properly flash the radio, they also will not have distortion detectors to properly setup the amp
Your amp is too small, we can get you setup with a plug n play amp with correct power for your speakers and rent you the tool to flash the radio as well, reach out to our sales team @ 1-844-30AUDIO
another great video Jay. one question though. i have the older GT6.5 unit. does it operate the same as the GTS in that once started it re-sets the curve? i should have the dealer flash my radio to a boom 2 amp setting and get rid of my BT35 that i originally installed....which by the way was long before i found your videos
Yes the flash works the same on gt or gts, and yes both radios have an eq that changes while running till flashed
I got a used 2018 road glide special, it has Rockford front speakers and soundigital 4ch amp, the Treble is so aggressive it hurts my ears, can't get it up very high.. I have no idea if it was flashed or not. Any recommendations for a place in DFW, Texas?
Sorry I don’t have anyone in Texas
My local shop flashed my 2018 street glide with the 2 speaker no amp flash and said it would level things out. Is this flash ok or should I have him reflash. I am installing 4 speakers 1 amp. Thanks
2 speaker no amp flash is the factory installed flash that does not work correctly
@@volunteeraudio thanks for your reply. What exactly should I tell him the flash is that I want? Thanks again
Do you ever do Road kings ?
We do
@@volunteeraudio do a TH-cam on one 👍
I have hertz neo speakers and a ordered the precision power 800w plug and play kit for my street glide from you guys for stock radio is it going to sound better than stock or should I be looking to send it somewhere to flash it to make a difference. ?
It must be flashed as we set all gains and filters on the amp for a flashed stock radio, we send directions showing which flash must be done
@@volunteeraudio ok so I’ll take those directions to a shop Or will it be cheaper to buy the part and do it myself the ones on your website are for 2014 and up I need for older 2009.
@@HillbillyFun-yr5pc ok, on the 2009 you should not have to flash the radio, just properly set the amp gains
@@volunteeraudio thanks you guys are great
@@volunteeraudio but y’all do that before sending it out for me?
Does the brand of amp matter?
Most aftermarket amplifiers will use this flash, some amps from hogtunes require the no amp stock flash
Dealer tells me it's my imagination. When I shut of my 18 street glide radio sound is increased bass and treble. So annoying need it fixed.
Not your imagination
First Harley rider I've seen wearing a mask.
This was at the beginning of Covid
Does him wearing a mask bother you? 😂