Always tighten your inlet hoses with a wrench, 1/2 to 1 turn. The water is under pressure and hand tight hoses might come loose from the machine vibration.
European plugs = ventless model. You also can see a small drain line going from the dryer @4:19. So, it's either 1) Condenser dryer or 2) Heat pump dryers (same sealed system as in your refrigerator).
Judging by the very high efficiency rating on the front I’m assuming it’s a heat pump dryer which don’t need ventilation. Either way it’s not required to vent a vented tumble dryer outside in Australia because most people will only use them a few days in winter
Any type of condenser/heat pump condenser dryer doesn't need venting. It condenses the steam into water which can flow either down the drain (if you pipe it) or into the container which you will need to empty
Costco just delivered this machine but didn't cap the transit holes and left. I know this because the caps are sitting there in the package. There is no way I can get behind the machine now because its in a small closet and the machine weighs over 300 lbs. How important is it to have the holes capped? I'm worry that lint and dust can get in there and mess up the machine.
Roughly 3-4 minutes to figure out how to get it off the dolly followed with another few minutes of how to connect a hose to a hose bib. Two outlet cords probably going on the same circuit with no 220, 221, whatever it takes, in sight. Not a sniff of a mention about the dryer side hookup. No need to relieve the weight of the 300 lb machine when leveling it either. Thank goodness they showed how to install the 4 delivery mounting caps back on. And seriously though, did they actually trim out a hole on the top of the countertop for this thing? Lol. They already had a hole on the side of the cabinet. Wouldn't the logical, easier, and aesthetically pleasing mounting option be to create your suction on the back of the machine with a sheet metal screw and then just run those two hoses through the side of the cabinet? All wrapped up with some music that reminds me of the old Baby Einstein dvds. This wasn't exactly what I envisioned when setting out to play this video.
What does it mean when the dryer makes a clicking noise. when you place your hand on the dryer it stops. When you take your hand away it starts. The noise happens on both sides of the dryer.
My washtower is to be out installed in a basement with limited ceiling height. I believe about 82”. What would be the minimum height required to maneuver into place?
@@Eddie-gb3bn washtower is awesome so far. I have done a few hundred loads already works great. Delivery was no issue because it comes in two pieces.. only complaint is how hard the relays turn the water on and off. It makes my pipes bang
@@michaelcharach Now that you have had you wash tower for awhile would you still recommend it and how do you find the dryer for drying without a vent compared to vented dryers?
Absolutely needs the washer and dryer hose (they are both drains / escapes) as it's the only way they are vented. You could probably rig one up or buy as a spare part for your situation.
@@chuckwhite1101 Not a video fail. This is a Heat Pump dryer. They don't require venting to the outside. They convert the steam into water, which is what the drain is for on the dryer.
I installed this same model today. The customer said it wobbled out of place and scratched their door. It was in a very tight space. I just don't see how it wobbled out of place. Uneven load? Idk 🤷♂️. Customer is upset.
I have washer/dryer combo model# WKGX301HBA. The kits included are: 1. Small wrench/accessories (# AAA36585217 AF) 2. Eastman 48" Gas Dryer Connector Hose with fittings (Eastman# 99930CS) 3. 4 foot water hose, 2 pack (GE# WH41X10207) 4. 8 foot Flexible Duct for Dryer (GE# WX08X10086)
Hahaha, I want to see that too. I bet, those two guys would break plastic drip pan. They could barely install it in a open, easy space without a drip pan. Now, try installing this laundry center into a plastic drip pan with the drain connected and pan is not moving and cracking😅, in a tiny laundry room, with 90° install needed, where appliance dolly useless and cannot fit inside laundry room and install needs to be done by hand, where cabinets won't let you go on the sides, where the POS Indian husband and wife standing behind, watching and telling us none stop what and how to do (to the point of several argument and last was telling them to GTFU and STFU or we're out). Me, and another strong 350lbs person did that install in 2012...never again!!!
This particular model does not vent to inside or outside. It is ventless, uses a heat pump (dehumidifier) instead of current-sucking resistive heating elements. The same air is recirculated within the dryer; no air from the dwelling is sucked outside (further energy savings).
Why doesn't LG just put locking wheels at the bottom? It is so difficult for the average person to move the tower to clean behind it and also clean the dryer duct. My boyfriend and I could not budge the tower. Refrigerators have wheels. Baby carriages have locking wheels. If they could do it for babies then certainly it could have been done for laundry towers.
Always tighten your inlet hoses with a wrench, 1/2 to 1 turn. The water is under pressure and hand tight hoses might come loose from the machine vibration.
The manual says do not lean the unit front or back only side to side to remove the tray base foam
Where can you buy the drain junction ? (White part at 6:57)
is it not included?
how come you didn't show how to install the dryer vent ?
European plugs = ventless model. You also can see a small drain line going from the dryer @4:19.
So, it's either 1) Condenser dryer or 2) Heat pump dryers (same sealed system as in your refrigerator).
Guess it doesn’t need a dryer exhaust vent?
Exactly what I was thinking
Judging by the very high efficiency rating on the front I’m assuming it’s a heat pump dryer which don’t need ventilation. Either way it’s not required to vent a vented tumble dryer outside in Australia because most people will only use them a few days in winter
Any type of condenser/heat pump condenser dryer doesn't need venting. It condenses the steam into water which can flow either down the drain (if you pipe it) or into the container which you will need to empty
@@anasazi112condensor dryers exist, a tub collects the water and you empty it
@@killianmmmooreyes but in this one I think as it’s stacked, the water goes into the outlet where the wash water goes . Am i correct
what about connecting the dryer vent?? looks like it doesn't have one??
This is likely the ventless model I'm eyeing
I’m looking for the same connection 😅
This is the heat pump dryer version.
can you please reupload this video without the music
No
turn your vol down..lol
Yes, we'll do that right away.
Can you raise the unit at all? Is there a pedestal that would fit, or should I buy a generic pedestal?
Costco just delivered this machine but didn't cap the transit holes and left. I know this because the caps are sitting there in the package. There is no way I can get behind the machine now because its in a small closet and the machine weighs over 300 lbs. How important is it to have the holes capped? I'm worry that lint and dust can get in there and mess up the machine.
Does the dryer vent inside or outside ????
The LG WashTower is ventless. There is a small cleanout on the lower-left front to capture lint.
Roughly 3-4 minutes to figure out how to get it off the dolly followed with another few minutes of how to connect a hose to a hose bib. Two outlet cords probably going on the same circuit with no 220, 221, whatever it takes, in sight. Not a sniff of a mention about the dryer side hookup. No need to relieve the weight of the 300 lb machine when leveling it either. Thank goodness they showed how to install the 4 delivery mounting caps back on. And seriously though, did they actually trim out a hole on the top of the countertop for this thing? Lol. They already had a hole on the side of the cabinet. Wouldn't the logical, easier, and aesthetically pleasing mounting option be to create your suction on the back of the machine with a sheet metal screw and then just run those two hoses through the side of the cabinet? All wrapped up with some music that reminds me of the old Baby Einstein dvds. This wasn't exactly what I envisioned when setting out to play this video.
I wonder if they supply the 7 zip ties to connect the drain to the faucet?
Video caption says to leave 200mm behind the unit. There is barely 100mm there. Does this need to be adhered to to avoid fire risk?
What does it mean when the dryer makes a clicking noise. when you place your hand on the dryer it stops. When you take your hand away it starts. The noise happens on both sides of the dryer.
Every specification I've seen says LG Washtower is 165.5cm tall. How tall are the people in this video?
My washtower is to be out installed in a basement with limited ceiling height. I believe about 82”. What would be the minimum height required to maneuver into place?
I would say to give yourself at least 6 inches to maneuver.
@@Eddie-gb3bn washtower is awesome so far. I have done a few hundred loads already works great. Delivery was no issue because it comes in two pieces.. only complaint is how hard the relays turn the water on and off. It makes my pipes bang
@@michaelcharach Now that you have had you wash tower for awhile would you still recommend it and how do you find the dryer for drying without a vent compared to vented dryers?
@@denisebrenton1897 love it. I do lots of laundry about 7to 10 loads a week, it works great. My dryer is vented.
My dryer is not turning on dont know why is a brand new unit
Does it need dryer vent?
No
Weren’t the colored plugs in the water inlets of the washer supposed to be removed first? They look like would block the water flow.
Those are filters designed to catch sediment. You should periodically check them and take them out if they become dirty.
There's no water hose into the dryer itself?
The dryer only has a drain hose for the condensed water after drying
How much the total load?
Apparently I don't have the drain hose for steam (bought used) will it be ok to run and just not use steam option?
Absolutely needs the washer and dryer hose (they are both drains / escapes) as it's the only way they are vented. You could probably rig one up or buy as a spare part for your situation.
@LGAustralia it's got me baffled as there's a water inlet but no drain under the black cover for the dryer. Every video I see there is one
where the dryer vent
How about a video on how to connect the dryer vent and also do the side venting on a gas dryer
Exactly, video fail
It’s a heat pump dryer. They don’t need ventilation because they recurculate the air
@@chuckwhite1101 Not a video fail. This is a Heat Pump dryer. They don't require venting to the outside. They convert the steam into water, which is what the drain is for on the dryer.
Is there a connection application for an apartment WITHOUT Washer/Dryer Connection? And without Electric Dryer 220Volt Power-Connection?
I installed this same model today. The customer said it wobbled out of place and scratched their door. It was in a very tight space. I just don't see how it wobbled out of place. Uneven load? Idk 🤷♂️. Customer is upset.
Did you take off transport screws? If yes, probably badly leveled machine, badly leveled base/floor with combination of overloaded machine
Loved your video on the LG wash tower. Can you tell me the length of the drier cable ? Thanks
Dónde consigo el diagrama eléctrico de éste equipo???
Why is there two electric plugs ?
Europe, 1 cord for each unit, 110/120 per cord.
Nde trae enchufe la secadora o que ?
Why were the 4 bolts taken off and plastic caps put on? Is that for the washer and dryer to keep from shaking?
Those hold the drum in place during shipment, they have to be removed before using the washer.
@@chuckwhite1101 is it okay if I don’t have the caps to put on after the bolts were taken off?
@@chuckwhite1101how bad would it be if they were removed after the first wash?
Por que se mete agua a la secadora ?
Anyone know the part number for the supplied accessory kit from LG??
I have washer/dryer combo model# WKGX301HBA.
The kits included are:
1. Small wrench/accessories (# AAA36585217 AF)
2. Eastman 48" Gas Dryer Connector Hose with fittings (Eastman# 99930CS)
3. 4 foot water hose, 2 pack (GE# WH41X10207)
4. 8 foot Flexible Duct for Dryer (GE# WX08X10086)
How you going to slide it into a space like that if theres a drip pan for second floor instalations?
Hahaha, I want to see that too. I bet, those two guys would break plastic drip pan. They could barely install it in a open, easy space without a drip pan.
Now, try installing this laundry center into a plastic drip pan with the drain connected and pan is not moving and cracking😅, in a tiny laundry room, with 90° install needed, where appliance dolly useless and cannot fit inside laundry room and install needs to be done by hand, where cabinets won't let you go on the sides, where the POS Indian husband and wife standing behind, watching and telling us none stop what and how to do (to the point of several argument and last was telling them to GTFU and STFU or we're out). Me, and another strong 350lbs person did that install in 2012...never again!!!
Brute force or furniture moving srtaps
You did not show dryer exhaust hookup
This particular model does not vent to inside or outside. It is ventless, uses a heat pump (dehumidifier) instead of current-sucking resistive heating elements. The same air is recirculated within the dryer; no air from the dwelling is sucked outside (further energy savings).
Good job 👍
how great trying to fit that in the back of the van
It comes apart in two pieces
what's the problem with using pliers to tighten the hoses ? a couple quarter turns just to be safe ?? nothing wrong with that
Does anyone know what’s the amp power plug for this machine
Eye knew I wasn't going nutzz! Like,"Why won't the dryer come on? (Ding!)Has it's own separate plug! Ha!.......darn."
Why doesn't LG just put locking wheels at the bottom? It is so difficult for the average person to move the tower to clean behind it and also clean the dryer duct. My boyfriend and I could not budge the tower. Refrigerators have wheels. Baby carriages have locking wheels. If they could do it for babies then certainly it could have been done for laundry towers.
Turn the music down please!
and this one time, at washtower camp
I have bad experience with LG washer it's not working right it's terrible washer new I returned twice 😁😁😁😁
Slick!
Lho vista oggi a Mailand
E una torre molto elegante e tecnologica
poor installation at 4:24 scratch the frame body. This is very common the "so called" professional pretend they have skills. And charge you not cheap.
Take off the bs music in the background
What the heck is that so many mistakes
Johnson Kevin Anderson Margaret Gonzalez David
Please do NOT scratch mine like you did this one!
What are we, a bunch of idiots
No talking, lame
You guys don't explain anything Jesus christ
336 Hayley Ferry