I'm a mechanic 👨🔧👨🏭, I have 16 experereants. I have a chainsaw and I fix it some Times. I know how to repair small engines, cars, motorcycles. I love your videos 🤝8-)
My chainsaw stopped working since last week it has no spark,after disconnecting ignition wire it sparks a lil though. I would like to know what should be done next
My Chinese chainsaw which is new has the same symptom. Run strong when cold then dies and won't start when warm. I replaced the carburetor. Same thing starts right up when cold. Why would coil fail when warm?
I normally don't get into comments but I must thank you. I have a Stihl 012AV that most certainly had an issue with dying when it got hot. Your comment that the spark plug can contribute to this saved me! You cannot purchase an ignition module anymore for my saw...so I thought I would at least try the spark plug after your comment...it worked!!! Before the saw would fire up no problem, run great...then die once it was hot. I replaced with a brand new NGK, it fired up, it got hot, it got hotter, it screamed, it wailed...it did not die! Before getting a new module one must try a new plug first. Thank you for your help!
Love my ms261C but replaced both oil pump $120 and ignition module $170 in first 3 years. Have a 1984 sthil 028 wood boss only part ever had to replace was carb boot. I’m pretty handy fixing stuff but Donny your videos are the absolute best on you tube and are very helpful to me. Thank You
Thanks for taking the time to upload. Managed to fix 'no spark' issue. It turned out not to be the ignition unit but a combination of bad earth and loose switch cable. You gave me the confidence to properly open up and investigate. Cheers from SCOTLAND!
I'm working on two identical MS194Ts. First is why did Stihl make it so hard to get the plug wire off the plug and to adjust the high low screws on the carb. One saw runs but idles too high and if i adjust the idle down it dies. The other saw has no spark. As always, Donny...Great videos
Thank you so much for all your instructions! You've walked me thru three repairs so far and your step by step diagnosis and repair instructions are so easy to follow. So glad i didn't chuck my ms170 to the trash bin. I've probably cut about four or five cords of almond and fig wood since installing my ignition coil with your help. Again thank you.
Great troubleshooting video. Thanks for running the saw. Always nice to see the repair all the way through. For anyone passionate about IC engines, we always love to see them come alive.
Great video had no idea where the ignition module was and troubleshooting a grounded ignition,fixed myself on the farm saved me time and money thank you very very much Dan
Excellent video Dony. Your production quality is right up there with DIY tv shows. It's obvious you spend a lot of time getting your shots just right, and editing the videos very well.
I tested my spark plug using your method. It was just a bad wire connection to control module and that fixed my Husqvarna's saw starting problem. Thank you so much!
Thanks for all of these videos. Neither my MS180C nor my 026 Pro would start after sitting for a year. Using your diagnostic tips and some relatively inexpensive parts, I have them both up and running.
So if I have spark after removing the positive, it's an electrical problem. What would you think the electrical problem might be? Do you have another video that might cover that?
Great video Dony, However, I would like to add one more tid-bit of advice. I have a Poulen 2250 that was driving me crazy. I had checked for spark and the spark plug was sparking fine but it would not start. Even with starter fluid it would not start. The carb was good, the gas lines were good, good compression, the spark plug was sparking but it would not run. Then I noticed an unusually large gap between the ignition coil and the flywheel. Why or how that happened I’ll never know. After I properly gapped the ignition coil the old 2250 runs like a new one. Thought I would share that with you so you can pass it on.
Thanks Dony! My saw won't start. No spark. The shop is two weeks out to repair it. But; thanks to you, I'll order a new coil kit and fix it myself and save a bunch of money by doing so.
this hus 240 has me stump no spark replaced coil/flywheel removed ground lead also check coil to ground new spark plug and still no spark turn flywheel with drill motor approx 1500 rpm and still no spark any suggestion
I especially liked the tip about disconnecting the positive wire isolates it to the coil exclusively. That made me much more confident to order a new coil. Thanks!
You made my day after my Ms660 stopped working when hot. I thought I had flooded it, but no spark, I had a coil on hand, with your instructions it was back at work within 15 minutes. It started 1st pull the next morning. Thanks.
I liked the way you diagnosed the problem and fixed that chainsaw. I have a Stihl chainsaw which is hard to pull over and don't want to start for me. The saw have been in the shop several times and I still have problems with it. After the problems I have had my solution is to never buy another Stihl saw again.
New subscriber here, I have a 044 Stihl chainsaw. Recently, it only ran when it was cold and shut down once it warmed up but now it won't even start no more. I strongly believe it's the ignition module, haven't replace that for many years. Thanks for the info video.
Thank you so much for your time and knowledge. You have given me the confidence to this seventy year old timer to rebuild my Stihl MS180C. You do a great service. Denny, Caope Cod
Another great and helpful video. I have this same saw and can’t figure out how to plug the hole for winter operation. Am I missing a part to cover the hole for summer?
Thanks, helped me quickly diagnose a Chinese 6200 62cc chainsaw where the on off switch was bad right new from the factory. Once I unplugged that black wire from the coil the spark plug was sparking while cranking. I'm sure that definitely means they don't do quality control or start each one up before packing them up. Anyway, ordered 5 new switches from ebay for half the price that one would cost shipped from a USA seller. While it's probably gonna take up to a month to arrive, I just turn it off with the choke, they turn off fine that way too.
great video again Dony. I am working on a new MS261C m-tronic saw that has no spark. I also found that when the chain break is engaged you cannot pull the recoi. I pulled the break cover off and found one of the tension springs was broken. I wounder if that may have contributed to the no spark issue. I'll do some more troubleshooting and make sure it's the coil.
Excellent Help. Following your instructions to replace the MS 280 ignition module it now starts right up. However, at one point you mention starting problems could also be in some other part of the electrical system. Now, some time later after cutting a cord or two my saw will not TURN OFF when I move the switch to the OFF position. It sure would be nice to see more info about the other parts of the electrical system and what kinds of problems they might typically have.
Thank you for the very descriptive video. I don't know small engines at all and all other vids say magnets at top, but don't say what they are. So thank you from a new home mechanic for the great video!
Is ignition module failure a known problem with the MS 270, MS 280 saws? I've had an MS 270 for at least a dozen years, and I just had to replace my 5th module. This last one cost $160 from the Stihl dealer. I use the saw, maybe, 6-8 times a year, so it's not like it's getting a ton of use. I'm just getting frustrated at having to keep replacing a module, when I could buy a brand new equivalent saw for 3 times the price of the module. I'm tempted to just buy cheap aftermarket modules, because, if nothing else, I'll feel like I got my money's worth if it fails in a year or 2. Any thoughts?
I picked up a dolmar PS 420 that won't start only pops once..has spark. Immediately suspected the coil..checked flywheel key just to be sure...great video thanks
hey pal, southern cally big dood here, i kinow theres naysayers in our world, but after THIS video, why would ya want to do a thumbs down. Great Great info. Blessings as always, snj
One of the first things I check is the position of the bayonet lug on the end of the spark plug wire. These can be undone by users pulling the spark plug wire, haphazardly. I usually take my carb adjustment screwdriver and insert it in the boot and feel for the bayonet lug in the bottom of the boot. A lot of times it has been pushed back down the end of the boot where it can no longer connect the spark plug If this happens, I pull it out of the boot , connect it back on the spark plug wire and inset it back into the boot and re-check it for spark. A lot of times this fixes the problem, sometimes not. I then troubleshoot the coil if I still do not have spark, but this is my first check. .
After replacing the ignition module I tried testing for a spark by turning the flywheel rapidly using my hand. When I did not get a spark I assumed the problem hadn’t been fixed. Come to find out you can’t turn the flywheel quickly enough by hand to get a spark. Once I reinstalled the recoil starter I had a good spark.
On the Stihl 048 AV electronic chainsaw, what is the proper name for the circular part that is under the flywheel? and how do you test it to make sure it is good or bad. Thanks for your time
Hello I have a chainsaw homelite 340, its coil ignition burns, I have not found on the market a replacement for the same model, can I use another model of a other brand? thanks for your vide
Obviously I'm having these problems since I'm here. I have an MS271, but mine looks newer. I looked up both, ignition module, which I bought and searched coil. Photos online look like the same exact part. I anticipate mine is headed to a repair shop.
I have a Poulan P3314 chainsaw. I have a electrical problem with saw. Saw looks new, I'm going to have replace fuel lines and filter. What do I need to check or might need to replace with electrical problem?
Doc I got a got a stihl fs80r trimer 4137 3401 and put a new ignition coil 4137 -400-1350 and switch is good but no spark? Thank you for the videos you doing a good job!
Running saw & suddenly lots of smoke , now won’t start , no spark at plug . Do you reckon the module has overheated & needs a replacement? Is there anyway of testing it ?
A business card is usually fine for setting the air gap, as long as it is .010 thick. Some are thicker. The Stihl spec is .15-.30mm, or .006-..012 inches, so a .010 thick business card is fine.
Hello Donyboy73 thank you for your videos, I have an ms170 and the spark plug always carbonize and the air filter looks clean, I see bad combustion and the carburetor does not adjust, I wonder what is the problem with this saw.
Question, Several older family members cannot pull their lawn mowers due to compression.You earlier showed a compression release on a chain saw. Have ever heard of anyone installing a compression release in the head of a lawn mower? Due you have any suggestions? Thanks for the videos.
Hi Don. I have a Stihl MS211/C chainsaw in Australia that I have to replace the flywheel on. I accidentally sheared the key on my old one when I was trying to remove the clutch by trying to remove it the wrong way. (I had a severe brain fade ) .. I now have a new flywheel and wonder if you need to remove the ignition coil first to provide clearance and the correct way to torque up the nut on the flywheel . I would follow your advice by using a business card to provide the correct flywheel magnet/coil clearance. If you know the correct torque specs it would be useful to confirm. I think 28 Newton Metres ?. I have been looking on your site for flywheel removal / installation but not having too much success. Any help would be much appreciated.
Thanks, I did your test and unplugged the black wire and then checked and it had plenty of spark. I think the problem might be in the switch. Any videos on switch replacement/and further checking of the wires.
Any idee why these ignitions typical stop working after about 5 min use ? I like to know/understand the physical problem occuring in the ignition coil when warm ...
Question I have a stihl 024 Av starts great runs great until you raise it above your shoulders then it dies out. Fresh gas it has . Dealer has it claims coil ignition but does it take 3 weeks or longer to get part?
I was replace the seals on my stihl 025 and the piston like ur video u had on yt. I have no spark with credit card gab...about 1,10 mm. So on internet i figure out the gab must be for my saw 0,2-04 mm. Now I have spark but is poor. I try 0,20, 0,25, 0,30 mm gab but its the same. That means I have to change ignition kit? Ty
I have a question. I have a stihl 210c that had a melted clutch. So I ordered a After market gas tank/engine cover. The problem is that the holes that mount the ignition module are not the same. Any way of figuring out what updated module would fit in new saw body? Thanks for your help..
On an older unit which has points which may be problematic, is there an easy way to determine whether the coil is the problem without having to to go all the way into the points?
My Stihl blower SH86c does not spark. The blue cutoff switch wire is also broken. Does that broken wire prevent spark at the plug? I personally do't think so because the cutoff switch hasn't worked for a long time and the machine still was able to start. I would flood the motor to get it to stop. Would the blue broken wire really prevent it from starting at this point? Thanks for responding back.
As you've done a video about a rev limiting issue with one in the past, I thought that I'd ask you about the OEM coil for a 2007 Stihl MS361. As you may recall, the coil in question is the Stihl 1135 400 1300. This is the third time we've had issues with this expensive ignition module (coil), so I was wondering if Stihl ever came up with a better coil for the MS361? If not, do you know of a coil that came in a different Stihl saw that's a suitable substitute for the 1135 400 1300? Thank you.
All good info. one bit you should mention , that is the Spark plug is a Resistive type and that if you use a none Resistive Spark plug or HT lead type then you will damage your control board.
Imagine how many Stealerships must hate you for giving us all this good information. However, they don't have to worry as 99% of people out there will never try to repair their own equipment. Too busy, or too scared, or too lazy.
Both wires were open and frayed before taking it apart, good chance that could be the problem, also double check with multi meter... Plus the gaps were way different Good job
Does your chainsaw only run until it gets warm, or will it not even start at all? It could be that you have weak or no spark at all at the spark plug.
I'm a mechanic 👨🔧👨🏭, I have 16 experereants.
I have a chainsaw and I fix it some Times. I know how to repair small engines, cars, motorcycles. I love your videos 🤝8-)
My chainsaw stopped working since last week it has no spark,after disconnecting ignition wire it sparks a lil though. I would like to know what should be done next
My Chinese chainsaw which is new has the same symptom. Run strong when cold then dies and won't start when warm. I replaced the carburetor. Same thing starts right up when cold. Why would coil fail when warm?
@@zmanphx eB
@@berylmohd what is eb?
I normally don't get into comments but I must thank you. I have a Stihl 012AV that most certainly had an issue with dying when it got hot. Your comment that the spark plug can contribute to this saved me! You cannot purchase an ignition module anymore for my saw...so I thought I would at least try the spark plug after your comment...it worked!!! Before the saw would fire up no problem, run great...then die once it was hot. I replaced with a brand new NGK, it fired up, it got hot, it got hotter, it screamed, it wailed...it did not die! Before getting a new module one must try a new plug first. Thank you for your help!
TH-cam is great; excellent videos like this allow us DIYs to save a lot of money. Thank you.
Love my ms261C but replaced both oil pump $120 and ignition module $170 in first 3 years. Have a 1984 sthil 028 wood boss only part ever had to replace was carb boot. I’m pretty handy fixing stuff but Donny your videos are the absolute best on you tube and are very helpful to me. Thank You
Thanks for taking the time to upload. Managed to fix 'no spark' issue. It turned out not to be the ignition unit but a combination of bad earth and loose switch cable. You gave me the confidence to properly open up and investigate. Cheers from SCOTLAND!
I'm working on two identical MS194Ts. First is why did Stihl make it so hard to get the plug wire off the plug and to adjust the high low screws on the carb.
One saw runs but idles too high and if i adjust the idle down it dies. The other saw has no spark.
As always, Donny...Great videos
Just buy a Husqvarna
Thank you so much for all your instructions! You've walked me thru three repairs so far and your step by step diagnosis and repair instructions are so easy to follow. So glad i didn't chuck my ms170 to the trash bin. I've probably cut about four or five cords of almond and fig wood since installing my ignition coil with your help. Again thank you.
I would like to add to my previous comment,what is really astounding about you is this you take the complex an make it simple!!!!👍
Great troubleshooting video. Thanks for running the saw. Always nice to see the repair all the way through. For anyone passionate about IC engines, we always love to see them come alive.
Great video had no idea where the ignition module was and troubleshooting a grounded ignition,fixed myself on the farm saved me time and money thank you very very much
Dan
Excellent video Dony. Your production quality is right up there with DIY tv shows. It's obvious you spend a lot of time getting your shots just right, and editing the videos very well.
I passed silver school but your videos really help better than the modules on icademy
I tested my spark plug using your method. It was just a bad wire connection to control module and that fixed my Husqvarna's saw starting problem. Thank you so much!
Thanks for all of these videos. Neither my MS180C nor my 026 Pro would start after sitting for a year. Using your diagnostic tips and some relatively inexpensive parts, I have them both up and running.
So if I have spark after removing the positive, it's an electrical problem. What would you think the electrical problem might be? Do you have another video that might cover that?
Great video Dony, However, I would like to add one more tid-bit of advice. I have a Poulen 2250 that was driving me crazy. I had checked for spark and the spark plug was sparking fine but it would not start. Even with starter fluid it would not start. The carb was good, the gas lines were good, good compression, the spark plug was sparking but it would not run. Then I noticed an unusually large gap between the ignition coil and the flywheel. Why or how that happened I’ll never know. After I properly gapped the ignition coil the old 2250 runs like a new one. Thought I would share that with you so you can pass it on.
Thanks Dony! My saw won't start. No spark. The shop is two weeks out to repair it. But; thanks to you, I'll order a new coil kit and fix it myself and save a bunch of money by doing so.
this hus 240 has me stump no spark replaced coil/flywheel removed ground lead also check coil to ground new spark plug and still no spark turn flywheel with drill motor approx 1500 rpm and still no spark any suggestion
Great teaching! Very clear and no wasted time. Thank you!!!
I especially liked the tip about disconnecting the positive wire isolates it to the coil exclusively. That made me much more confident to order a new coil. Thanks!
You made my day after my Ms660 stopped working when hot. I thought I had flooded it, but no spark, I had a coil on hand, with your instructions it was back at work within 15 minutes. It started 1st pull the next morning. Thanks.
I liked the way you diagnosed the problem and fixed that chainsaw. I have a Stihl chainsaw which is hard to pull over and don't want to start for me. The saw have been in the shop several times and I still have problems with it. After the problems I have had my solution is to never buy another Stihl saw again.
Thank you for the video. Great job, straight to the point with no rambling on how to replace the module.
Best no nonsense chainsaw tutorial channel.
New subscriber here, I have a 044 Stihl chainsaw. Recently, it only ran when it was cold and shut down once it warmed up but now it won't even start no more. I strongly believe it's the ignition module, haven't replace that for many years. Thanks for the info video.
thanks, is an ignition coil the same as a magneto? The retail shop said my ms250 magneto was bad.
This video is one of the best I've seen in a while. I learned quite a bit watching.
Thank you so much for your time and knowledge. You have given me the confidence to this seventy year old timer to rebuild my Stihl MS180C. You do a great service. Denny, Caope Cod
You make it look easy, sometimes things will fall into place and some times not so much.
hay dony thanks for donate your time to help others, you make the world a better place.
Another great and helpful video.
I have this same saw and can’t figure out how to plug
the hole for winter operation. Am I missing a part to cover the hole for summer?
dony boy is a great technician.very helpful
Very good. You explain the process and reasoning very nicely.
Precise and explained simply . Top job :)
Thanks Don. The coil on my little MS211 seems to have gave up. This video was exactly what I needed.
Excellent presentation simple/short and clear.
Thanks, helped me quickly diagnose a Chinese 6200 62cc chainsaw where the on off switch was bad right new from the factory. Once I unplugged that black wire from the coil the spark plug was sparking while cranking. I'm sure that definitely means they don't do quality control or start each one up before packing them up. Anyway, ordered 5 new switches from ebay for half the price that one would cost shipped from a USA seller. While it's probably gonna take up to a month to arrive, I just turn it off with the choke, they turn off fine that way too.
great video again Dony. I am working on a new MS261C m-tronic saw that has no spark. I also found that when the chain break is engaged you cannot pull the recoi. I pulled the break cover off and found one of the tension springs was broken. I wounder if that may have contributed to the no spark issue. I'll do some more troubleshooting and make sure it's the coil.
Excellent video. Step by step and very clear with great tips.
Thank you. Excellent presentation.
Excellent Help. Following your instructions to replace the MS 280 ignition module it now starts right up. However, at one point you mention starting problems could also be in some other part of the electrical system. Now, some time later after cutting a cord or two my saw will not TURN OFF when I move the switch to the OFF position. It sure would be nice to see more info about the other parts of the electrical system and what kinds of problems they might typically have.
great video and super presentation skills. To the point, clear explanations and FREE. Thanks a lot.
Dony thanks you so much I had a weak coil it would start some time had me question what was wrong. Your videos are easy to understand God bless you.
Great video Tony, very informative and super easy to follow.
Thank you for the very descriptive video. I don't know small engines at all and all other vids say magnets at top, but don't say what they are. So thank you from a new home mechanic for the great video!
thank you for showing us how easy it could be to find the reason with ignition problems! Great job !
Is ignition module failure a known problem with the MS 270, MS 280 saws? I've had an MS 270 for at least a dozen years, and I just had to replace my 5th module. This last one cost $160 from the Stihl dealer. I use the saw, maybe, 6-8 times a year, so it's not like it's getting a ton of use. I'm just getting frustrated at having to keep replacing a module, when I could buy a brand new equivalent saw for 3 times the price of the module. I'm tempted to just buy cheap aftermarket modules, because, if nothing else, I'll feel like I got my money's worth if it fails in a year or 2. Any thoughts?
Great instructional video. Thank you!
I picked up a dolmar PS 420 that won't start only pops once..has spark. Immediately suspected the coil..checked flywheel key just to be sure...great video thanks
hey pal, southern cally big dood here, i kinow theres naysayers in our world, but after THIS video, why would ya want to do a thumbs down.
Great Great info.
Blessings as always, snj
Superb, clear advice, thanks very much, job done, my saw is back running so I am a happy boy again.
These coils are expensive. I have been looking for an aftermarket. But no luck. Thanks Don. Great video. I recognised the part # in the your comments.
One of the first things I check is the position of the bayonet lug on the end of the spark plug wire. These can be undone by users pulling the spark plug wire, haphazardly. I usually take my carb adjustment screwdriver and insert it in the boot and feel for the bayonet lug in the bottom of the boot. A lot of times it has been pushed back down the end of the boot where it can no longer connect the spark plug If this happens, I pull it out of the boot , connect it back on the spark plug wire and inset it back into the boot and re-check it for spark. A lot of times this fixes the problem, sometimes not. I then troubleshoot the coil if I still do not have spark, but this is my first check.
.
After replacing the ignition module I tried testing for a spark by turning the flywheel rapidly using my hand. When I did not get a spark I assumed the problem hadn’t been fixed. Come to find out you can’t turn the flywheel quickly enough by hand to get a spark. Once I reinstalled the recoil starter I had a good spark.
Excellent tutorial, I will try on my non-Stihl chainsaw as its not starting.
On the Stihl 048 AV electronic chainsaw, what is the proper name for the circular part that is under the flywheel? and how do you test it to make sure it is good or bad.
Thanks for your time
Hello
I have a chainsaw homelite 340, its coil ignition burns, I have not found on the market a replacement for the same model, can I use another model of a
other brand?
thanks for your vide
I have the same problem with an echo kiuritz cs302! There should be a workaround on that...
Obviously I'm having these problems since I'm here. I have an MS271, but mine looks newer. I looked up both, ignition module, which I bought and searched coil. Photos online look like the same exact part. I anticipate mine is headed to a repair shop.
Nice video. Informative, high def, good camera work, Good naration. Thanks!
Thanks Danny for making the universe make sense again. 😊
4:40 I dont know on witch side i have to put the paper to make space. Thank you for all video you share with us.
Great video. Does this apply to a MS 291?
Really good, helpful and informative guide. Thank you
Great video, easy to follow and understand.
Thanks a lot brother have a blessed day 🙏
I am a stihl tech i like how the inside of the saw was clean
I have a Poulan P3314 chainsaw. I have a electrical problem with saw. Saw looks new, I'm going to have replace fuel lines and filter. What do I need to check or might need to replace with electrical problem?
Doc I got a got a stihl fs80r trimer 4137 3401 and put a new ignition coil 4137 -400-1350 and switch is good but no spark? Thank you for the videos you doing a good job!
Running saw & suddenly lots of smoke , now won’t start , no spark at plug . Do you reckon the module has overheated & needs a replacement? Is there anyway of testing it ?
A business card is usually fine for setting the air gap, as long as it is .010 thick. Some are thicker. The Stihl spec is .15-.30mm, or .006-..012 inches, so a .010 thick business card is fine.
Hello Donyboy73 thank you for your videos, I have an ms170 and the spark plug always carbonize and the air filter looks clean, I see bad combustion and the carburetor does not adjust, I wonder what is the problem with this saw.
check spark arrester screen
Thank you, it was completely plugged
Question, Several older family members cannot pull their lawn mowers due to compression.You earlier showed a compression release on a chain saw. Have ever heard of anyone installing a compression release in the head of a lawn mower? Due you have any suggestions? Thanks for the videos.
Hi Donnie. I have a sthil Ms 251. No spark after installing new coil, new coil and new spark plug. Can you help? Love your podcast. Thanks
Thanks donnyboy after watching several of your video's I gained enough confidence to rebuild an old jonsered 2150 and she runs well
Hi Don. I have a Stihl MS211/C chainsaw in Australia that I have to replace the flywheel on. I accidentally sheared the key on my old one when I was trying to remove the clutch by trying to remove it the wrong way. (I had a severe brain fade ) .. I now have a new flywheel and wonder if you need to remove the ignition coil first to provide clearance and the correct way to torque up the nut on the flywheel . I would follow your advice by using a business card to provide the correct flywheel magnet/coil clearance. If you know the correct torque specs it would be useful to confirm. I think 28 Newton Metres ?. I have been looking on your site for flywheel removal / installation but not having too much success. Any help would be much appreciated.
Thanks, I did your test and unplugged the black wire and then checked and it had plenty of spark. I think the problem might be in the switch. Any videos on switch replacement/and further checking of the wires.
Thank you for all the valuable information... you inspire me to fix my own equipment... thanks again.....
Do you not get a shock when holding the spark plug cap & pulling the cord ?
Any idee why these ignitions typical stop working after about 5 min use ? I like to know/understand the physical problem occuring in the ignition coil when warm ...
Great video Dony!
Question I have a stihl 024 Av starts great runs great until you raise it above your shoulders then it dies out. Fresh gas it has . Dealer has it claims coil ignition but does it take 3 weeks or longer to get part?
I was replace the seals on my stihl 025 and the piston like ur video u had on yt. I have no spark with credit card gab...about 1,10 mm. So on internet i figure out the gab must be for my saw 0,2-04 mm. Now I have spark but is poor. I try 0,20, 0,25, 0,30 mm gab but its the same. That means I have to change ignition kit? Ty
possibly yes
I have a question. I have a stihl 210c that had a melted clutch. So I ordered a After market gas tank/engine cover. The problem is that the holes that mount the ignition module are not the same. Any way of figuring out what updated module would fit in new saw body? Thanks for your help..
I've had the spark plug close to the opening and pulled the rope, it does make a pretty good flash when the fuel ignites..lol
I have lost arm hair from that!
On an older unit which has points which may be problematic, is there an easy way to determine whether the coil is the problem without having to to go all the way into the points?
What is the gap on the plug?
Thanks
Matt
Great channel Donny 👍🏻
I have a homelite 45 cc 20" cut i put a new carburetor on it and i do have spark but changed the plug anyway but the saw will not start
You are a excellent teacher - thank u 4 your help & God bless u :)
hi, followed all yr instructions, change the module, but still no spark. What should i look for then?
Thank you I took this apart and needed help, getting it back together appreciate the detail
Great to hear!
My Stihl blower SH86c does not spark. The blue cutoff switch wire is also broken. Does that broken wire prevent spark at the plug? I personally do't think so because the cutoff switch hasn't worked for a long time and the machine still was able to start. I would flood the motor to get it to stop. Would the blue broken wire really prevent it from starting at this point? Thanks for responding back.
As you've done a video about a rev limiting issue with one in the past, I thought that I'd ask you about the OEM coil for a 2007 Stihl MS361. As you may recall, the coil in question is the Stihl 1135 400 1300. This is the third time we've had issues with this expensive ignition module (coil), so I was wondering if Stihl ever came up with a better coil for the MS361? If not, do you know of a coil that came in a different Stihl saw that's a suitable substitute for the 1135 400 1300? Thank you.
All good info. one bit you should mention , that is the Spark plug is a Resistive type and that if you use a none Resistive Spark plug or HT lead type then you will damage your control board.
my old homelite xl has no spark. new spark plug change ignition module, carb looks clean what do i do next?
thanks a lot sir good teaching big help tnx boyet in philippines 👍
Imagine how many Stealerships must hate you for giving us all this good information.
However, they don't have to worry as 99% of people out there will never try to repair their own equipment. Too busy, or too scared, or too lazy.
Thanks alot for your video it helped me fix my saw it was the coil awesome job
excellent video very easy to follow very helpful thanks so much
Both wires were open and frayed before taking it apart, good chance that could be the problem, also double check with multi meter...
Plus the gaps were way different
Good job
I have the same saw and exact problem. I installed a new ignition coil and still no spark? Weird. What else could cause no spark