TOP 10 ELECTRONICS PROJECTS USING CD4017 IC
ฝัง
- เผยแพร่เมื่อ 16 ม.ค. 2022
- Hi ,
This video is a series of top 10 CD4017 IC based electronics projects.
◾ Buy CD4017 - amzn.to/3qOL9fw
◾ Buy NE555 - amzn.to/3qSl8vH
◾ Buy Resistors - amzn.to/3tV7Al4
◾ Buy Transistor kit - amzn.to/3AsDzKD
◾ Circuit diagram - drive.google.com/folderview?i...
#top10 #ESTechKnowledge - วิทยาศาสตร์และเทคโนโลยี
people that do want to learn electronics, must in the first place learn to read a schematic. A schematic tells way more than thousand video or speech
I agree 100%. without a schematic this is just mindless Entertainment. If you're an EE or have a lot of electronic experience you can figure it out and draw the circuit on paper. I wouldn't attempt to build anything without a schematic.
Bonjour, bravo pour ces petits projets incroyablement propres ! Ça fait plaisir de voir le soin apporté aux connexions !
Un grand merci à vous pour la mise à disposition des schémas ! 😉
Hi I want to make a toggle switch with 4017 with 2 different loads. I want to shift between white and RGB led using push button switch. Can you please help me out?
EXCELLENT VERY NICE AND NEAT WE BOARDS VERY WELL MADE AND MUCH LEARNED FROM YOUR GREAT EFFORT THANKYOU AS USUAL INSTANT SUB AND THANKYOU
Thank you for Circuit diagrams
Sir RGB 5mm 4pin jisme 4017 ki do ic laga kar 10 channel ka chaser banaya hai video me to BC 547 Ka use kiya hai lekin circuit diagram me BC 557 Aur BC547 ka use kiya hai samaj me nahi aa raha hai please video ki hisab se circuit dijiye
No current limiting resistors on LEDs ?
4017 max sink-source current isn't a reliable way to control the LED current.
I checked the schematic there is no limiting resistor. I expected to see a 270-330 ohm with the 5 volt power supply, but none.
Rick Hunt no resistors required if the voltage is low !
@@pufango4059 clearly it works without buying up the led and the chip. for 5 volt I would have thought a 270 ish to 330 ohm would be used for the common on the leds.. It's not so much about voltage as it is current. for a red led. supply voltage - 1.7/ 10ma = limiting resistor. that's what I was going by.
@@pufango4059 I noticed he only used a 3.7v battery so well within the 3-5v range.
thanks for the great effort.
Bhai nice project hai aapke sare
Thanks, great job.
I have noticed at the start of each project, you show a Zero PCB, of which you don't show the size of the board and that would be helpful. It will just save us having to count the holes. The projects that you share with us are awesome, and some of which i will use, great job indeed. I would aslo like to know what wire you are using to connect your pins with please. Thankyou
I use single string of 1.5mm wire.
You guys shorty do like the LED lights!! I'm having problems trying to figure out what type of 555 timer I'll need or want! Or CMOS logic or inverter !! For high voltage generator and other high voltage consumptions. Of that nature!
In six one can I use a relay and connect a 220v bulb
Nice work
Thanks for the great efforts, I am try to do the same.
Can we use any other ir reciever? Or we should use the same which you used in the video?
You can use other IR sensor too.
Great👍
Which gouge of copper wire did he
Use? 21:47
Anybody knows ?
Amazing my friend ♥♥♥♥♥
Nice to meet you ♥♥♥♥♥
Best wishes for you ♥♥♥♥♥
Keep it up .............. ♥♥♥♥♥
Or How can I build a VFD control for a 3phase 1500kw water cold spindle motor!
🔝10 👍
Couldn't you find a bigger soldering iron?
I was thinking the same
Nice. Very nice if v get ready made board from u.
Где схеми? Къде е схемата на проекта с 4017 на зарядно?
I have used the 4017 alot
very good👍👍👍
Please explain how to connect more than one LED in each channel...I.e., minimum 10 LEDs to be connect for designing.
Use a 555 timer on a rf with 2 diff resistors..
Well done 👍..but share the diagram
Available in the video description
Pcb ka Don 😂
there are a couple of projects in this clip that i don't know where they could be used, i cant remember which ones they are. Can you maybe put on the screen as to what they might be used for please and thankyou again ?and does the wire you use have flux on it ?
Ba que vidio ralado cade o diagrama
For des 2. You have diagram
Good ..bhai g diagram share kia karo
Circuit diagram link is available in the video description.
Nice work, please can I get exp 5,9,10 circuit diagram please
Available in the video description
Thankyou letme check it out
Pls make fm reciver
Don't have any idea about fm receiver
1st like
Good video but far too long, should have broken it into 4-5 smaller videos
Bhai hamesa led project hi kyun?
Cause other videos doesn't get much views
@@estechknowledge yes i think so
Circuit diagram required
You *NEED* a new soldering tip! 😉
😁
Schematics missing... Hard to see the connections on this pcb masuhp - wires and more wires...
Dukan se saamaan laane ka footage bhi add kar dete.. just crap
led projects are boring.
we need
1 cell service jammer.
2 police digital communication jammer.
3 EMP to disable moving vehicle or kill every device in a city block.
3 GPS jammer.
4 cell phone sting ray router.
5 long range microwave ray.
Definitely NOT LED.
why ypu don't share the schematics ?
It's available in the video description sir
@@estechknowledgeHi, I followed the whole video, but no diagrams are visible, you only see how you mount everything.it is a tremendous effort to follow the components as you connect, what does it cost you to put the diagram too?
WARNING: No narration, and no schematics. Useless.
Agreed. Totally useless, and boring.
My video
Tq
Keep it up you channel 🤠😁
boss dk iske siwa kisi bhi youtuber ko aur kuch aata nhi kya...ek hi ic mili hai dunia me
Recommended video - th-cam.com/video/eZDOGXlPn2I/w-d-xo.html
@@estechknowledge bhag lode
Can you send me the circuit diagram of project no 2 on my email address