How to Replace Filters in MJJC Pro 2 & MTM PF22.2 Foam Cannons + Routine Maintenance
ฝัง
- เผยแพร่เมื่อ 19 ก.ค. 2024
- Intro 00:00
MJJC Filter Replacement: 00:56
MTM PF22.2 Filter Replacement: 10:19
#mjjcfoamlance #foamcannon #carcleaning #cardetailing #MTMpf22.2FoamCannon #AutoDetailing #MJJC
Original MJJC Pro 2 review video: • MJJC Foam Cannon Pro 2...
In this video, I show you how to replace the filters in the MJJC foam cannon pro 2, and the MTM PF22.2 foam cannon. Plus I have to do a little extra troubleshooting and maintenance with the MJJC foam cannon. I hope you find this video useful!
Please make sure to like, subscribe and ring the notification bell so you know exactly when future useful, helpful and informative videos like this are published! Thanks for watching!!
Visit us on the web for our package and service pricing, and check us out on social media! Please like, follow, and subscribe!
www.turnermobiledetailing.com
/ tmdetailingpa
/ turnermobiledetailing
/ @turnermobiledetailing
Tools and Products used/shown in this video:
Purchase the MJJC Foam Cannon Pro 2 here: www.mjjc.com/collections/foam...
MTM PF.22: clean-garage.com/mtm-pf22-2-f...
Purchase MJJC Filters here: www.mjjc.com/products/mesh-fi...
MTM Filter: clean-garage.com/mtm-stainles...
MTM Rebuild Kit: clean-garage.com/mtm-pf22-foa...
Plyers: www.amazon.com/Gerber-Dime-Mu...
Hex/Alan Key Set: www.amazon.com/AmazonBasics-H... - ยานยนต์และพาหนะ
Thanks for replying. I got it removed. It’s just a bit of force with a flat screwdriver on cut out piece nearest to the bottle end and it pops out (and then pops back in easily). Thanks again. 👍
After replacing the MJJC filters, I had the same moderate improvement. I punched out the filter in the weighted ball with a syringe and got the same results you got at the end. I'd rather bypass the dip tube altogether even if it means replacing the internal filters more often.
Yup, if you can have the weighted ball but no filter hinderance, should be golden.
The mtm probably has the best but worst nozzle to take off 😤 . It would be interesting to see if using the MJJC mesh filter inside the MTM would create better foam. Anyways nice job
same thoughts here, i would really like to know the answer to this
Nice work on this video. Thank you for showing how to replace the filters on these popular foam cannons. I have saved this video to a special playlist so I can find it later when I need it. Lots of work went into the editing! Good job.
Thanks very much, happy to help!
Good video i like this hack🎉
It's crazy how up until I found and watched this video, I had no issues with my mjjc foam cannon. Then I went to wash my car and had runny AF soap. Opened it up, adjusted the filter (until the replacement arrives) and it's kind of working. But it's just weird that until this video popped up on my TH-cam recommendation list, I had no issues with it at all.
Lol, strange phenomenon
@@TurnerMobileDetailingsadly the fixes didn't work for me. I have a 1.2gpm 1800 psi pressure washer and the foam is runny. I've ordered a replacement to see if my pressure washer is the problem or the foam cannon
@@TurnerMobileDetailing
I have a question buddy. Will that 3 piece filter fit any foam cannon, ? For example I have the red Bear Force clear bottle stainless steel foam cannon,would that 3 piece filter fit the bear force foam cannon? Would love to try it
Good question, and I’ve gotten the same question before. My answer is I don’t know, I’ve never tried that. I just use the factory suggested replacement filter. You can compare size specs for each filter and if they’re the same, it could work.
Thanks. Straight to the point!
Thanks a lot for this man, my mjjc pro v2 starts to just spit out water, i changed the filters and seems to work but still sputtering, I will clean out or modify the ball filter as in your video.
Great video, thank you.
Bro bro bro you are really doing a great work❤️❤️❤️…i dont think anyone else make such detailed videos like you…keep it up❤️❤️InshaAllah you will get more success❤️
Thanks so much!!!
Thanks a lot bro❤
Great video i have both cannons and might have to do this soon. 👍🏾 What pressure washer do you use?
I’m using an ARBC 675 Pro
Thanks for the video - really useful.
I have the MJJC. I recently dropped the cannon and broke part of the nozzle… only the black part. I ordered a replacement from MJJC. I see from your video how to remove the red and the black parts together (to replace filters) but do you know how to separate the black from the red (since I only need to replace the black part). It seems like brute force but I don’t won’t to break the red part also! 😮😮. Many thanks for your thoughts.
Cheers
Honestly I’ve never had to do that. I took a look at mine and didn’t see a clear way to separate the two. If they sent you the black part only, hopefully seethe piece on its own will give some indication as to how they come apart and go back together.
I’m gonna put the MJJC filter I bought online from them in my Adams premium phone cannon.
Let me know how that works
I like to put the mjjc filters in my cannons whenever they need a change. I don't have a pf22 though so I'd love to see how it performs after such a swap.
This video shows the after results from each cannon
@@TurnerMobileDetailing sorry for the confusion I meant I'd be curious to see if the MTM foams any better with The MJJC filter since MJJC claims that's where a lot of their foamy magical goodness comes from. I've replaced the filter in lots of my cannons with the MJJC filter and I do notice better results but they were all ready pretty crappy cannons to begin with so I was just curious what a good cannon would do with the MJJC filter.
@@muchachogrande2019 interesting, maybe I’ll try that next time they both need a filter change.
Would soaking the MJJC main filters in a vinegar solution clean them up like it did to the 'ball' filter?
Might save a few $$$.
It’s possible, it sounds worth it to save money on new filters. Let me know if it works.
Did it work?? Was thinking of cleaning mine out that way. Until I order new ones..
Nice video, it sure would be a lot easier if you had a Punch Set lol
That’s weird i been using mine for almost 3 years never had a problem still foaming good i use to fill it with warm water after i finish foaming my car and let it run for almost 20 seconds maybe that’s the trick😅
So if we want to be a little proactive, is it better to use filtered water to dilute the snow foam concentrate?
Filtered water still contains minerals. If you want to go that route you would use distilled water in the reservoir. However, you’ll still be running regular water from the hose, unless you have a reverse osmosis system.
I have buy a new mjjc v2 pro but do only water😂😂 so what i have to think? They have send me an used one? I use karcher k5 and mafra pre wash, and if i use the 12€ foam gun by karcher i got a very nice foam -.- i dont know how to fix this
Did you mention what snow foam product you're using?
Which one foams the best?
th-cam.com/video/4Omjn8P7tHQ/w-d-xo.html check out this video. These are two good foamers, Koch Kemie Super a foam foams well too if you’re looking for something stronger.
Excellent video. Well done.
Is there a link for your filter supplier or retailer?
Yes, all links are in the video description. Are they not working for you?
@@TurnerMobileDetailing Not at first. I kept clicking the "More..." but, nothing would happen. But, it works now.
My plan is to get an Active 2.0 and an MJJC foam cannon this summer so, I'm making a list of parts suppliers for the future.
Thanks for everything. 👍
@@imdeplorable2241 your welcome, glad it worked for you!
About what size would be the o ring for the quick connect part for mjcc s v.3.0?
I’m sorry I don’t know. I’m pretty sure you can purchase new o rings from mjjc
I have a MJJC myself. Not sure if it’s the same issue hope it is . But my MJJC won’t foam when I max the top nob all da way. I have to minimize the nob to get some watery foam . Hope you can tell me if this is the same issue you had ? Should I start with the filters first like the video ?
How many times have you used it?
@@TurnerMobileDetailing
I been having the foam cannon for about 3 months i use it on the weekends constantly. So I wash 2 to 3 cars every weekend.
@@mariaacosta7428 at that rate I’d say it’s probably about time to change the filters and clean or remove the filter at the end of the dip tube. Try that and see if that works
I had the exact same issue. I opened it up and pressed the filters using my finger towards the nozzle. That seemed to work but I ultimately bought new filters. Still not getting good foam though so I'll try removing the weighted ball and see if that helps
@@mariaacosta7428did you figure out what the problem was?
have you tried cleaning the MTM or MJJC filters probably keeping in distilled vinegar for couple of hrs and reuse?
I have not, let us know how it goes?
@@TurnerMobileDetailing I tried soaking in vinegar for couple of hrs 90% of all mineral and alkaline deposits will get cleaned out with that, then just add a spoon of baking soda and the reaction will remove remaining 10% acidic and hard alkaline deposit residue - it gets 100% cleaned, no need to buy filters unless it is damaged. Also I dont use the allen key to push the filter out that creates a depression and damages it.
@@kashi2843 which filter did you clean?
@@TurnerMobileDetailing mesh filter inside the cannon which you need to push out to access. I don't use the ball filter at all
Can you use an MJJC filter with the MTM PF22.2?
I honestly don’t know, i think they’re the same diameter so it’s a possibility. I’ll have to try it next time my filters need changed.
Is that the Brookyln 99 theme song in the beginning
No idea
Why can't you fill the bottle of the foam cannon with a cleaning agent and pull the trigger to flush out the filter?
I guess you could in theory. The foam filters inside the MJJC might not be flushable multiple times as they’re a fine grade foam and not stainless steel, thus less durable.
Has anyone put a filter from MJJC into the PF22?
Hid, did you find a way to remove the filter & attach the weighted ball. I am having problems with my Mjjc too.
Honestly no, I haven’t had a chance to put any time into that. I just removed the weighted ball/filter and left it off, it works great, I don’t think having a filter there is a big deal anyway, but the weighted ball was nice. I’ll get back to it eventually lol.
@@TurnerMobileDetailing Thanks for your reply & yeah i don't think a filter is a big deal either. I have just run a 2.5mm drill through the outer end of the ball to break through the end of the filter, so clearing out any debris & effectively making the filter defunct, then i have just re-attached the ball to the pipe. Not tried it yet but i will let you know if it's a success. 👍🏻
@@alantaylor2 good idea man, let me know how it works
@@TurnerMobileDetailing Tried it today & it’s as good as new if not better 👍
How did you remove the weighted ball? I feel like I’m going to rip the “plastic straw” when pulling on it lol
How to buy the filters
There are links in the video description
Hole punch and a hammer….instead of the Allen key.