Hello friend, I have that same icu in a 2002 Citroën C5, the signal does not reach injector 2 and 3, it comes from the computer. You will know which component you have to change.
Great job!!!! If i am correct because i don t know NOTHING about this ... Did you take the chip off the dameged one and put it on a jused one so you don t have to code it? I have a bmw module and i boucht another one but from the same car but not a cabrio but the number en is the same but it is fore electric use of the doors and windows and roof ... But the other is not a cabrio si will this work (every litle thing is the same inside ... Please help 🥴😅
Good job. How we can order SMD component all type I work in BMW all type modules. But I have no link how to get new component so I try with old modules
I did a larger bosch ic driver today. For anyone struggling, remove the backplate as this will sink all the heat youre putting in. Also, they are glued so when the solder is finally loose, you still have to forcefully yank it. Not fun
Hi. Can you tell me what was the error codes of the car? It's because I have a Peugeot 206 with the same ECU and the error is P0202 and P0203 and sometimes P0201 but it's not the injectors because I have substituted them. It only gives the error when I flore it rapidly. If I accelerate slowly it does not give the error. I can flore it to the red line and it stays good. It only throws the error is I am on low revs and flore it rapidly. I am puzzled by this because I think that if it was the driver the car would work on 3 cylinders or show some kind of failure and this does not happen. It only happens when I flore it from low revs. Thank you for your video and I will be waiting for your answer. Thanks.
Thanks for the reply.I play around alright but would like to get better understanding of components functionality and test methods.your channel is grate and knowledge to be able to fault find components 👍
Hı dear İ have Peugeot et3j4 1.4 16v engine İ have a question for u When my car warms up to 90 celcius. Start my car idle surfing up and down and sometime stop my car suddenly.. im very bored this problem.. We have 5 friends having the same problem. Do you have a solution for us 😥 ? And im sorry for my bad English Best regards
no sorry i dont this is all Electronics servicing to component Level - you can do electronic Engineering courses i guess would cover this , or just start to play around !
I read the comments and everyone said thank you, how could you thank a video that shows only garbage and waste of time that trying to desolder and resolder a chip? That was the most talentless soldering I have ever seen.
I thought exactly the same thing, I wouldn't be surprised if the new chip died from the heat the way it fried on it 🤦🏻♂️ Looks like his day job is a roofer and he used the roofing soldering iron.
Sir aapne fluks kon si company ka use Kiya jb hm IC ko soldering krte h to IC ki aaps me leg ek doosre se touch ho jati h
Question, is it possible to remove the board from the shield?
What function does that mar1909pd component have to do with the injectors???
In Toyota Yaris 2007 ECU where can I find immobilizer?
Hello friend, I have that same icu in a 2002 Citroën C5, the signal does not reach injector 2 and 3, it comes from the computer. You will know which component you have to change.
Great job!!!! If i am correct because i don t know NOTHING about this ... Did you take the chip off the dameged one and put it on a jused one so you don t have to code it? I have a bmw module and i boucht another one but from the same car but not a cabrio but the number en is the same but it is fore electric use of the doors and windows and roof ... But the other is not a cabrio si will this work (every litle thing is the same inside ... Please help 🥴😅
Good job sir. From the Philippines thank you for sharing.
What flux do you use?
I am really looking forward to your video, you do great work
Good job. How we can order SMD component all type I work in BMW all type modules. But I have no link how to get new component so I try with old modules
What was the problem symptoms on the car, that required this driver to be replaced? Thanks
I did a larger bosch ic driver today. For anyone struggling, remove the backplate as this will sink all the heat youre putting in. Also, they are glued so when the solder is finally loose, you still have to forcefully yank it. Not fun
hello what drive is for peugot 308 2009 and does bosch 30682 is a replacment for bosh 30680
thank you
Pro tip: if you dont remove the solder from the pin pads you can get the chip to just drop in place w/ the heat gun. 😜
Sometimes !
What kind of past are injectin there? Flux? Can you tell me the brand?
Hi. Can you tell me what was the error codes of the car? It's because I have a Peugeot 206 with the same ECU and the error is P0202 and P0203 and sometimes P0201 but it's not the injectors because I have substituted them. It only gives the error when I flore it rapidly. If I accelerate slowly it does not give the error. I can flore it to the red line and it stays good. It only throws the error is I am on low revs and flore it rapidly. I am puzzled by this because I think that if it was the driver the car would work on 3 cylinders or show some kind of failure and this does not happen. It only happens when I flore it from low revs. Thank you for your video and I will be waiting for your answer. Thanks.
Fuel filter??starvation?
Sir i have a mitsubishi pajero 1999 model after put wrong jump start wrong wire now chek light not showing what happened in ecu
Hi could you tell me what's the most common part on ecu that gets damaged due to short circuit?
I have a 02 Peugeot 607 and the computer is burned, I want to know what I should do.
Eek , that's a lot of aluminum to warm up . I'm guessing that's why you didn't use solder paste underneath ?
Nice repair there.
Hey man i have a 2008 peugeot 207 , they have common fault the the electronic power steering system , are you able to repair these ?
Wrong soldering method chosen. Bottom of IC was unsoldered (just ends) and will have problems with heat dissipation.
Oh yip, thanks for your comment
i think so
Hello Sir i need
f6a t/c 2wd 4at
33920-74G8 1 ka wiring diagram plz
can we ask some questions about the 7 to 14 pins of ecu to formatter?
Cooling fan is always on, even runs when engine is cold.. my mechanic said the problem is with the ECM board. is it so?
It depends on your car's whiring
What kind of Gel Flux do you recommend?
How did you figure out that was the trouble chip?
Thanks for the reply.I play around alright but would like to get better understanding of components functionality and test methods.your channel is grate and knowledge to be able to fault find components 👍
Peugeot which model ecu? Is it 308 or others?
what temperature did you use to desolder?
Sir plz make video on replacement of infeneon tricore 2nd generation mcu any fixing process
Send one in and il video it.
pretty cool.nice work
Hı dear
İ have Peugeot et3j4 1.4 16v engine
İ have a question for u
When my car warms up to 90 celcius. Start my car idle surfing up and down and sometime stop my car suddenly.. im very bored this problem.. We have 5 friends having the same problem.
Do you have a solution for us 😥 ?
And im sorry for my bad English
Best regards
Sorry cant help, I only repair what has been diagnosed
@@getelectronic8459 thank u for reply
MAF sensor (mass airflow sensor)
Those fluxes your using are same for removing and soldering
hi bro i have a cuestion, how many degrees use for desoldering de ic.
280 is what i use for ROSH or 240 for leaded Degree" C " also thank you so much for subscribing (: Welcome to Get Electronic
Get Electronic ok. Thanks.
Hi do you know of any good automotive electronic repair courses?Any help would be much appreciated.
no sorry i dont this is all Electronics servicing to component Level - you can do electronic Engineering courses i guess would cover this , or just start to play around !
What funtion is that iC ?
The drivers are responsible for the operation of the actuators, electrovalve egr, turbo, IAC, etc ...
Nice video😀
🇧🇷🇧🇷🇧🇷🇧🇷👏👏👏👏👏
Good lesson
the best sloving ECU board
💐 thank you sir 👍🏻
I read the comments and everyone said thank you, how could you thank a video that shows only garbage and waste of time that trying to desolder and resolder a chip? That was the most talentless soldering I have ever seen.
To je divne pajeni,tenky hrot a pajet od cipu a hned je hezky zapajene a ne tak cik cak do krize a zas odsavat moc zbytecne zkratovani .😮
I thought exactly the same thing, I wouldn't be surprised if the new chip died from the heat the way it fried on it 🤦🏻♂️
Looks like his day job is a roofer and he used the roofing soldering iron.
Nice job👍🏻
Kindly don't have the "music" we rather listen to you.
Nice info, thanks
Great job
Babyyyyyyy THAT THONG TONG TONG TONGGG TONGGG YEAHHHHHH !!!!!!!!!!! LIKE IF YOU LIKE SISQOOOOO
Nice VDO.
Nice hair!!!
ахренеть как долго и муторошно. на кой было убирать припой с дорог родной?
Делать ему нехуй.
Good job
İstanbul da yaşıyorum proton 1600motor otomatik şanzuman 98 model araba var beyin arızası var nasıl tamir edebilirim??
Professionalität kann man das nicht nennen, was hier gezeigt wird.
Ein Dachdecker bestimmt der nebenbei versucht auf Elektroniker zu machen 😂
Professional Job, not for the DIY Man!
EOIN henderson thank you for the feed back (: yeah it may be a bit up there in the difficulty level
ONE OF THE WORST WAY TO SOLDER THIS KIND OF CHIP ( HEAT SINK PADDED) YOU RUINED THERMAL CONDUCTIVITY
shit welds
Ok 👌 glad to have your feedback
is that signal input IC driver, that ypu replace?
Good job