I’m new to this hobby but seen tons on videos while I built my 3”, and setup my mobula. Never seen this done before, thank you so much for showing us! Exactly what i need!
This helped me a lot. Thank you! One adittion, though: This will not work wit UR/US/UK65, because the battery holder is higher than the motors. Just use a cardboard box and cut a hole in it, just big enough for the battery holder. Place whoop on box, calibrate, done!
This was a super helpful video! By getting the quad calibrated in stabilized mode like this it then carries over to acro mode. Holy heck, what a difference between the two modes though!
I think you mean horizon mode where it will self stabilize but will also still flip if sticks are pushed far enough. In acro the accelerometer is not used for any self leveling.
Thanks, just got my first FPV drone, I flied in acro buy I will calibrate angle mode so friends/family can try it indoors (its rainy all the time) . Acro is quite hard :D Btw in moblite7 only trimming would work, because of battery, the drone is not leveled when sitting on the ground
@@edrone_ Eah didn't know that, is that feature called Smart Audio? I would love to look it up and learn it on my own, thanks again for helping us noobies out! ♥
set p_pitch = 65 set i_pitch = 80 set d_pitch = 50 set f_pitch = 96 set p_roll = 65 set i_roll = 80 set d_roll = 50 set f_roll = 96 set p_yaw = 65 set i_yaw = 75 set d_yaw = 0 set f_yaw = 100
Another thing is try to mount the battery so its always in the same position, the more balanced the drone is the less the motors need to fight to keep it from drifting so its more efficient.
It could be this is basically the same thing just inputting the commands via the transmitter once you get it set just save it with the save stick command and it should be fine
I think I might have worked it out, I have throttle reduced to 50% on 2 x 1s indoors. puting it up to 100% allows me to carry out the calibration, but now it wont take off LoL
Im able to do the accelerometer with the sticks but i dont get the beeps for when I try to trim it left or right. I have the mobula 6 qx7 frsky flight controller
I think i got it to work i saw another video with joshua bardwell and when he does it you dont hear a beeping sound. You just trim and test it to see if it still drifting
So when you connect to betaflight do you see the adjustments there also after the stick inputs? For instance if i want to reset it or something or see how much i've trimmed in the past.
@@edrone_ Thanks, i just got my mobula today and damn it looked easier than it is. I dont really notice any difference between flightmodes that's how noob i am.
If your using your radio for multiple models you dont want to adjust the trim tabs on the radio as your other models will be affected and possibly fly poorly, also you always want your radio trim tabs centered for optimum precision
I just got my mobula 7, and it used to arm just fine but drifted backwards like crazy. So I did what you did in the video, but now my quad won’t arm at all. It just starts quickly beeping. Any suggestions? I would appreciate any help
Can you do this with the FlySky version? I have the i6X transmitter, and the Crazybee F4Pro FS receiver or flight controller. I’m new to this all. The level seems to work well I got mine pretty stable, but the trimming I don’t think works. Also, can you recommend a good battery for these other than the Happymodel 0.25mAh HV 4.35V 30/60C that come with it? And a good charger, cause this 6 in 1 is cheap and inaccurate...
edrone thanks brother! By the way I tried this last night and it made the beep for the calibration for the initial level part and worked well. But now I can’t seem to get it to do it again. It will make the beeps when I try the trimming tho so I dunno. Also for that charger you recommended, is there a port for a wall plug instead of using the Lipo? I guess I could get the wall plug but with the XT60 adapter on the end. Would that be the 12V output one tho? I’ll send you a link of the one I’m talking about and see what you think. www.amazon.ca/gp/aw/d/B07B9TYN2K/ref=ox_sc_saved_image_2?smid=A1UO2CSKOWQ5H6&psc=1 EDIT: So I’ve now figured out that when I hold throttle top left, pressing down does nothing. Yet if it press left it beeps once, Up beeps twice, and right beeps 3 times. Any idea what functions that is activating?
Any idea why the stick command does not work for me. Mode 2. Is there any setting in betaflight i need to set. I tried in turn on flight acc cal in betaflight but not helping.
@@edrone_ QX7 Taranis. I think probably the end point of the stick They are less than 100 less then 2000, and 100 more 1000. Did stick calibration didnt help. And output screen from q7x doesn't let me change much. Will try betaflight command
@@edrone_ i found the extend limit setting from the tx and able to increase or decrease to 150% instead of only 100%, and able to get all min pmend point to 1000 and all max to 2000, all but not yaw. Yaw still around 100 less and more. Strange. Then the drone couldn't fly even i armed it. I then figured it out to change the throttle min point to something like 899 or max point to 1899, i forgot which one, should be min end point, then it can fly. That value was the old value it had before. Dont get it why. Now i can use the stick commands. So now the yaw is not 1000 and 2000, do you think it matters and better change in betaflight.
young betaflight sees 1000 as min and 2000 as max as long as your close within probably 10 or 15 points you should be fine any higher you may need to change in the cli just set your endpoints to whatever the value is in betaflight when they are all the way down and all the way up and it should make it read 1000 and 2000
@@binceproductions4352 there should be a trim adjustment in betaflight on the configuration tab i believe you can adjust that way to try and fix the drifting.
![☀ Cinewhoop - РАКЕТА. Лучший БК вуп с HD камерой. [Mobula 7 HD]](/img/n.gif)
I like the dog just chillin on the sofa watching the Mobula7. I've had my a quad chased by dogs several times, he seems like he's just cool!
Sean C. Haha yea my cat tried the first time, now she just runs or watches it!
My dog is still undecided as to weather my drone falls into the squirrel category yet.
I’m new to this hobby but seen tons on videos while I built my 3”, and setup my mobula. Never seen this done before, thank you so much for showing us! Exactly what i need!
This video is a life saver. I've been trying to deal with drifting on my whoop for weeks now. Finally I got the accelerometer calibrated properly.
Glad to hear please like share and subscribe!!!
This helped me a lot. Thank you! One adittion, though: This will not work wit UR/US/UK65, because the battery holder is higher than the motors. Just use a cardboard box and cut a hole in it, just big enough for the battery holder. Place whoop on box, calibrate, done!
Best method ever!! Saved me so much time and grief! Thank you!!
Thanks for your support! Please like and subscribe!!
THANK YOU SO MUCH!!! It was getting really annoying having the drift indoors
No way! How did you even figure that out?? Thanks for sharing this! Awesome.
Really? It's all in the docs. I always carry a printed version of the stick commands with me. Still nice to see it done in a video.
Thank you for this information. I have the QX7S and did not know this. Thanks again.
Thank you so much for this review. Just got my mobula7 a couple of day ago and this will surely help....Happy New Year!
This was a super helpful video! By getting the quad calibrated in stabilized mode like this it then carries over to acro mode. Holy heck, what a difference between the two modes though!
I think you mean horizon mode where it will self stabilize but will also still flip if sticks are pushed far enough. In acro the accelerometer is not used for any self leveling.
Woohoo brother!! Came back here to fix drift, you are the man Erik!!! 👊😎👍👍👍
Thanks brother its alot easier than trying with the micro USB plugged in
@@edrone_ absolutely!! Thanks again!!
Thank you so much for making this video!
Thanks. This was a very helpful video.
Thanks, just got my first FPV drone, I flied in acro buy I will calibrate angle mode so friends/family can try it indoors (its rainy all the time) . Acro is quite hard :D
Btw in moblite7 only trimming would work, because of battery, the drone is not leveled when sitting on the ground
That's so cool!
Is the stick function specific to the FrSky transmitter?
I hope not cause I'm using a Turnigy Evolution flying a Snapper 6 here
Im pretty sure its for betaflight so you should be able to use other manufacturers transmitters
@@edrone_ Eah didn't know that, is that feature called Smart Audio?
I would love to look it up and learn it on my own, thanks again for helping us noobies out! ♥
Thanks for the vid..
Thank you!
Great information thanks. Will this work for most of the smaller quad copters I wonder? Happy New Year and Happy flying.
As long as they are using betaflight yes
I love how you explain everything and hired George Bush as voice over.
Wow, great info. Thank you.
What are your PIDs please? And great video
set p_pitch = 65
set i_pitch = 80
set d_pitch = 50
set f_pitch = 96
set p_roll = 65
set i_roll = 80
set d_roll = 50
set f_roll = 96
set p_yaw = 65
set i_yaw = 75
set d_yaw = 0
set f_yaw = 100
Thankyouso much. Ill try this right away
Thanks for this vid. how do you go to mode 2?
Thank you 😊 In the radio setup menu choose mode 2 and then you should be good 👍
Nice tip, thanks!
Great video very helpful tips thanks for posting 1 new sub for you mate
Another thing is try to mount the battery so its always in the same position, the more balanced the drone is the less the motors need to fight to keep it from drifting so its more efficient.
Super! Thank You!
Thanks for sharing. Would drifting be completely resolved if calibration was done in Betaflight?
It could be this is basically the same thing just inputting the commands via the transmitter once you get it set just save it with the save stick command and it should be fine
Hi, Does this method also can be applied to other drones? 3 inch or 5 inch drone?
Yes as long as its using betaflight
i can not do it with my tina whoop and qx7
I have a Mobula 7 V2 in mode2 and that doesnt work for me.I cant see what I could be doing wrong.
I think it may depend on firmware version and different receiver types is yours frsky?
I think I might have worked it out, I have throttle reduced to 50% on 2 x 1s indoors. puting it up to 100% allows me to carry out the calibration, but now it wont take off LoL
@@edrone_ yes, im wondering if its a battery level issue. Ill have a play :-)
How do I get into mode 2
In the model setup page all the way at the bottom of the page is the change modes.
Im able to do the accelerometer with the sticks but i dont get the beeps for when I try to trim it left or right. I have the mobula 6 qx7 frsky flight controller
Is your beeper functions on?
Yes its on a switch
@@Takeover738 are the leds blinking when you make the trim adjustments?
I think i got it to work i saw another video with joshua bardwell and when he does it you dont hear a beeping sound. You just trim and test it to see if it still drifting
@@Takeover738 ok 👌 i could not remember if mine beeped or if the leds just flashed
So when you connect to betaflight do you see the adjustments there also after the stick inputs?
For instance if i want to reset it or something or see how much i've trimmed in the past.
Yes you will see the adjustments you made on the sticks in the Beta flight configurator in the configuration tab
@@edrone_ Thanks, i just got my mobula today and damn it looked easier than it is.
I dont really notice any difference between flightmodes that's how noob i am.
@@exposer3339 we are all noobs my friend lol
@@edrone_ Hej i just tried the stick controls but no luck for me, dont see any trim changes in betaflight, i have smartaudio enabled
@@exposer3339 are you getting a beep and a flash after doing stick commands?
Why not just press the trim tabs instead?
If your using your radio for multiple models you dont want to adjust the trim tabs on the radio as your other models will be affected and possibly fly poorly, also you always want your radio trim tabs centered for optimum precision
My head started spinning when I started to dig into onscreen settings. Any chance you could do a video on what the various configurations do?
Definitely
th-cam.com/video/bC1glNNlxIs/w-d-xo.html
Love u soo much sir
Thanks!! Please like share and subscribe!!!
Mine Yaws to the left, slowly spinning. How do I fix the yaw?
Check your controller and add deadband for yaw possible fix
@@edrone_ as hard as it is to get going in this hobby. The community really makes it all possible. Thanks.
@@seang354 happy to help 😊
I just got my mobula 7, and it used to arm just fine but drifted backwards like crazy. So I did what you did in the video, but now my quad won’t arm at all. It just starts quickly beeping. Any suggestions? I would appreciate any help
Sounds like possible battery issue or your throttle stick is not at zero when you arm possibly
@@edrone_ Turns out when i tried to trim it i messed up throttle settings which triggered the alarm. All fixed now
Thanks. This was a very helpful! subs
Can you do this with the FlySky version? I have the i6X transmitter, and the Crazybee F4Pro FS receiver or flight controller. I’m new to this all. The level seems to work well I got mine pretty stable, but the trimming I don’t think works. Also, can you recommend a good battery for these other than the Happymodel 0.25mAh HV 4.35V 30/60C that come with it? And a good charger, cause this 6 in 1 is cheap and inaccurate...
Not sure with the flysky I mean in theory it should work because its changing the trims in betaflight so I would try it and see
Charger: www.racedayquads.com/products/ultra-power-up-s6ac-6x4-35w-1s-ac-dc-lipo-lihv-battery-charger-with-micro-mx-mcpx-jst
Battery:www.racedayquads.com/products/rdq-series-300mah-1s-45c-hv-lipo-battery-ph2-0-plastic-head
edrone thanks brother! By the way I tried this last night and it made the beep for the calibration for the initial level part and worked well. But now I can’t seem to get it to do it again. It will make the beeps when I try the trimming tho so I dunno. Also for that charger you recommended, is there a port for a wall plug instead of using the Lipo? I guess I could get the wall plug but with the XT60 adapter on the end. Would that be the 12V output one tho? I’ll send you a link of the one I’m talking about and see what you think. www.amazon.ca/gp/aw/d/B07B9TYN2K/ref=ox_sc_saved_image_2?smid=A1UO2CSKOWQ5H6&psc=1
EDIT: So I’ve now figured out that when I hold throttle top left, pressing down does nothing. Yet if it press left it beeps once, Up beeps twice, and right beeps 3 times. Any idea what functions that is activating?
Interesting, l always used my trim tabs
Normally you want to leave all your trim tabs on your radio centered and trim your accelerometer
Is this FrSky protocol?
Yes
Any idea why the stick command does not work for me. Mode 2. Is there any setting in betaflight i need to set. I tried in turn on flight acc cal in betaflight but not helping.
What transmitter are you using?
@@edrone_ QX7 Taranis. I think probably the end point of the stick
They are less than 100 less then 2000, and 100 more 1000. Did stick calibration didnt help. And output screen from q7x doesn't let me change much. Will try betaflight command
@@kevchyoung9205 you definitely want your endpoints to be correct you can set them in betaflight cli if the transmitter settings wont get you there
@@edrone_ i found the extend limit setting from the tx and able to increase or decrease to 150% instead of only 100%, and able to get all min pmend point to 1000 and all max to 2000, all but not yaw. Yaw still around 100 less and more. Strange. Then the drone couldn't fly even i armed it. I then figured it out to change the throttle min point to something like 899 or max point to 1899, i forgot which one, should be min end point, then it can fly. That value was the old value it had before.
Dont get it why.
Now i can use the stick commands.
So now the yaw is not 1000 and 2000, do you think it matters and better change in betaflight.
young betaflight sees 1000 as min and 2000 as max as long as your close within probably 10 or 15 points you should be fine any higher you may need to change in the cli just set your endpoints to whatever the value is in betaflight when they are all the way down and all the way up and it should make it read 1000 and 2000
can it work for mobula7 HD?
Yes
@@edrone_ thanks bro
I'm using a TBS Tango 2 and looks like this method doesn't work.
Are you using betaflight?
@@edrone_ yes I do, but tried calibrating with the radio but seems like it doesn't work.
@@binceproductions4352 thats weird what drone are you using?
@@edrone_ betafpv meteor75
@@binceproductions4352 there should be a trim adjustment in betaflight on the configuration tab i believe you can adjust that way to try and fix the drifting.
😎👍
Curious, after you make these changes and fly a few packs, put everything away, does it retain the fixes for next time?
It does save the calibrations but may need adjustments in future flights from crashing and shifting around the flight controller
Just got a sub from me thanks
Dude it never sits flat on the battery and a ball of wires are you kidding me
That's why you trim The accelerometer
You have to save it
how do you save it?
@@joegirty6609 both sticks Down and outsides. (Left down to the left. And right stick down to the right)
@@Ike92 O.k. thanks. i'll give it a try.
Fly in acro and you don’t get drift. Problem Fixed.
I do fly acro outside however when the weather is not good I fly stabilized mode in doors on 1S it's not that hard to calibrate the accelerometer