@@CGOD That's my next step lol. We decided to buy a house before another vehicle. Looking to get one by the beginning of next year. I've had my car for 7 years, that hooptie ain't going nowhere.
It’s my brothers truck but pretty much he drilled holes in the bed floor to be able to extend the wires and fuel lines and hooked the tank up like normal
hey bro I was wondering if you had any problems in the front? did you rub on 7 inches? I ordered 3 inch lowering springs but I have 5 inches rn so I’m thinking or wondering if it’s gonna be a problem going 8 inches in the front with 22s
@@CGOD Ohh I really appreciate it bro, I might have to get some thinner tires and hopefully be able to run 22s with the 8in drop and relocate the fuse box, if not I might just have to go with 20s
@@CGOD I have 265/35 rn hopefully it does fit and is the relocation with the fuse box hard to do? and how much did you end up cutting the fender? like a good amount or most of the front fender? also really appreciate you for responding man 🙌🏼
@@chrisluvsu relocating it isn’t too hard, usually the entire inner fender is cut out. You could take it a step further and tub the fenders then it’s possible to just lay the fuse box on top
I did a 4/6 drop on my GMC Sierra and I have the damn Chevy lean.... It’s sitting lower on the drivers side than the passenger side.... I cut a 1/4 inch of the coil off but she’s still has the lean.... I’m thinking maybe I should cut another 1/4 inch off....
Crippin’ 4 LYFE idk man, I’ve heard of people running one drop shackle at 2” and the other at 1” to even it out also. Or a stock shackle and a 1” drop shackle
Hey bro i got the exact same truck but in the front my sway bar links keep bending and then snapping off in half any ideas on what it could be i went about 6 inch drop
I have the same drop on rear but some how my rims still fuck my bed up is it due to taking off the plastic wheel well that comes on the bed? Do u have the same probelm?
This truck being a step side the bed has no wheel tubs inside. Your wheels might be the issue though. 10” wide will barely fit and rub sometimes. Narrower wheels will clear easier. But yes if anything is rubbing you can remove it or cut out your wheel tubs inside the bed if you have a fleetside
I would say narrow your differential, if not then you can shave the metal off with a sanding disk aswell. Some people say it makes it flimsy but atleast it would clear
@@CGOD yeah thats why I haven't grinded it down I heard the same about it making it flimsy. I might try the baseball bat trick lol. Until I can get smaller tires and 9" wide wheels. My current set up is 22x9.5 wheels with 305/40 tires. Shits to wide
hey bro I have texas carbon 24 on the rear and I got the same drop, how come my bed is like hitting my wheels like I can’t even stick a dollar bill in there it’s so tight lol is that how urs is and you just live w it or what
Obviously the alignment is gonna be off because you cut the tie rods like some fools instead of marking them before removal like normal people. You could have put the new ones one same place you took the old ones off
rmartinezg93 does it really matter? We had to adjust the toe anyways after lowering the truck more. Original tie rod placement would’ve been changed anyways
Juan Colunga just a billet antenna off eBay bro www.ebay.com/itm/Chrome-Billet-8-High-Gain-Radio-Antenna-Ford-Chevy-GMC-RAM-Truck-RECON/172281232465?epid=2205191801&hash=item281cc2fc51:g:dzMAAOSwgotcQfuS
Nice
Real dangerous mfs 😂 premium content
Never cut your springs kids
You can do whatever you want to your stuff
“Ole 7/11 ass nigha” 😂😂😂😂
That's a clean looking truck man. I really need to get me a truck now. I've had a car for way too long now.
05 P71 I’ve always been into cars too, had a family and needed shit moved. Had to get a truck lol
@@CGOD That's my next step lol. We decided to buy a house before another vehicle. Looking to get one by the beginning of next year. I've had my car for 7 years, that hooptie ain't going nowhere.
I had to buy a truck to move all my shit to my house lmao
Looks super clean
Nice content, good seeing some fools that actually know what theyre talking about
Coronitas thanks bro! We try
Just found your channel, picking up an 03 5.3 silverado soon. Great content hope to see more vids 💪🏽
Content is a little slow but I plan on making new videos weekly eventually lol need to start working on my truck again
9.1M views is a 5.3 the best motor to get on these trucks?
StepSide GanG 🤘
I ain't a big fan of the extended cab's, but that mfr looks good sitting like that🤘🏽
Bitch is clean. I just bought a truck just like this but all stock . Hard to find them like this.
Hell yeah man!
Did u have any problems with the drive shaft
Sorry for the late reply but this truck had the crossmember notched to clear the driveshaft with no issues
You have a 1 piece drive shaft or 2 piece
random saulo_vlogs it originally came with a 2 piece driveshaft, we did have to notch one of the crossmembers for it to clear.
You can tell these vatos are from texas w that llanta talk...😂😂😂
Dpmode TapiaBeltran haha we from Kansas bro!
😂😂😂 definately not Cali😎😎 nice truck tho
Sickkk truck G
J owens thanks for the love!
Bro could you make a video on how you ran your gas tank up there?
Like a walkthrough I guess please ?
It’s my brothers truck but pretty much he drilled holes in the bed floor to be able to extend the wires and fuel lines and hooked the tank up like normal
Damn that truck sounds sick af what kind of muffler you have?
Erick Medina it’s running an SLP loudmouth
@@CGOD stupid af
What you drop it in the back with
It’s on 6” flip kit, 2” shackles, and 3” drop blocks
Sick👍
Damn, safety glasses are like 2 dollars, your eyes are not.
joshua6200 what can I say, he’s a wild boi
Cute drop
Where’d u get that cowl hood ???
My brother ordered it, I’m not for sure from where
What kind of rims are those
Ruben Aguilar they’re 24” Yukon replicas
Truck looks clean i bet changing the oil is a bitch but truck still looks clean
for the 11” on the back did you have to adjust the shocks?
Jaime Barrera yeah it has shock extenders with small shocks, we wanna do custom shock mounts on it eventually
hey bro I was wondering if you had any problems in the front? did you rub on 7 inches? I ordered 3 inch lowering springs but I have 5 inches rn so I’m thinking or wondering if it’s gonna be a problem going 8 inches in the front with 22s
If tires are too big you’ll rub on the inner fender. This truck had the inner fenders cut out and fuse box relocated
@@CGOD Ohh I really appreciate it bro, I might have to get some thinner tires and hopefully be able to run 22s with the 8in drop and relocate the fuse box, if not I might just have to go with 20s
@@chrisluvsu 22’s on 265/35 should still work, it’s just the bigger wheels and tires that’ll be your problem but truck will sit real low to the ground
@@CGOD I have 265/35 rn hopefully it does fit and is the relocation with the fuse box hard to do? and how much did you end up cutting the fender? like a good amount or most of the front fender? also really appreciate you for responding man 🙌🏼
@@chrisluvsu relocating it isn’t too hard, usually the entire inner fender is cut out. You could take it a step further and tub the fenders then it’s possible to just lay the fuse box on top
0:38 *osha didn’t like that*
Drizzylsd definitely not OSHA approved!
Hey bro howd you guys set the pinion angle on this ?
sadam bomb I think he’s running a shim in the back for pinion angle but I’m not for sure
Ku ku bro thanks !
I did a 4/6 drop on my GMC Sierra and I have the damn Chevy lean.... It’s sitting lower on the drivers side than the passenger side.... I cut a 1/4 inch of the coil off but she’s still has the lean.... I’m thinking maybe I should cut another 1/4 inch off....
Crippin’ 4 LYFE idk man, I’ve heard of people running one drop shackle at 2” and the other at 1” to even it out also. Or a stock shackle and a 1” drop shackle
Just get a leaf spring lift shackle for the low side
I have the djm lift shackle brings it up 1in
Is it anyway you would have a link for that exact hood bro I checked summit racing but can't really tell what's the right one
i dont have a link but its the only cowl hood available for 03-04 silverado
Was there any issues with the tank back there ? Im doin that to mine and im just wondering, and how did u guys extend all that ?
1slo_ext _ no issues so far, we just used gas line to extend those and the same size wire to extend the wiring
CGOD thanks for replyin bro !
Did you just have to buy more of the same plastic line and what fittings do u buy mines 8 in rear right now but need to move the tank to go another 2
We just extended the original lines so we used the same fittings. Just used fuel hose and hose clamps to extend them
@@CGOD ok cool so just use rubber house and i guess brass barb fittings and clamps
Would it hit the top of the tub bad when turning ?
This truck had the tubs cut out and some stuff relocated under the hood to not rub
Do you need tubs on the front
MOPAR_LSX _SVT_JDM for this one we just cut out what we could without relocating anything. Clearance is minimal
Hey bro i got the exact same truck but in the front my sway bar links keep bending and then snapping off in half any ideas on what it could be i went about 6 inch drop
You’ll have to get relocated sway bar links for it to work properly
Where can i get those at?
@@Joshsotojustss I’m not for sure, my brother said he used stock links and didn’t have any issues
@@CGODthanks bro for replying your gto is sick asf too
What are those wheels called
They’re Tahoe replicas
How u install the corners of yo wing?
Miguel I think they’re installed with screws
I have the same drop on rear but some how my rims still fuck my bed up is it due to taking off the plastic wheel well that comes on the bed? Do u have the same probelm?
This truck being a step side the bed has no wheel tubs inside. Your wheels might be the issue though. 10” wide will barely fit and rub sometimes. Narrower wheels will clear easier. But yes if anything is rubbing you can remove it or cut out your wheel tubs inside the bed if you have a fleetside
Sick truck! Did you guys roll the rear fender? If so how you do it
The rear fenders on stepsides are plastic, we used a sanding disk on a grinder to remove the lip so the wheels don’t rub
@@CGOD yeah I got a regular bed and it has a metal lip thats shredding my tire. Trying to figure out best way to fix this issue
I would say narrow your differential, if not then you can shave the metal off with a sanding disk aswell. Some people say it makes it flimsy but atleast it would clear
@@CGOD yeah thats why I haven't grinded it down I heard the same about it making it flimsy. I might try the baseball bat trick lol. Until I can get smaller tires and 9" wide wheels.
My current set up is 22x9.5 wheels with 305/40 tires. Shits to wide
I wouldn’t roll it with a bat cause it’ll make the bedsides look wavy, I would shave it and leave a little material so it stays strong
hey bro I have texas carbon 24 on the rear and I got the same drop, how come my bed is like hitting my wheels like I can’t even stick a dollar bill in there it’s so tight lol is that how urs is and you just live w it or what
The bedsides were shaved on this one to clear.
@@CGOD I shaved mine too but they’re still touching
@@zenah7248 I’ve seen some people extended the bedside mounts to kind of “widebody” it and clear. This truck had a plastic bed cause it was stepside
@@CGOD yea mines stepside too, hm i’ll see
@@zenah7248 fack, best option is to narrow the differential
Do you have problems because of the wheel base going over speed bumps?
Angel Zavala usually try not to take it over speed bumps
Where y’all located let’s link?
Pablo Hernandez we in Garden City, KS
CGOD let’s link bro I got a 08 ram
Pablo Hernandez my truck is still a work in progress, my bro would be down to cruise probably. I just got my Lincoln right now
Obviously the alignment is gonna be off because you cut the tie rods like some fools instead of marking them before removal like normal people. You could have put the new ones one same place you took the old ones off
rmartinezg93 does it really matter? We had to adjust the toe anyways after lowering the truck more. Original tie rod placement would’ve been changed anyways
What year is the truck ?
Saul Solis it’s an 03
What kinda hood anyone know ?
Nathan Ogliastri cowl hood for 03-05 Silverado
What type of hood is that I know it's a cowl hood but what's the specs on it an the name of it for that year truck
Zavier Cope yeah man it’s just a steel cowl hood for 03-05 Silverado
@@CGOD ok thanks bro
4wd or 2wd ?
2wd
Nice video dude. Didn't realize his bed was like that lol that things sweet
Thomas Hoang thanks man! Yeah, it could use a notch cover lol
What is the name of the antenna? Link?
Juan Colunga just a billet antenna off eBay bro
www.ebay.com/itm/Chrome-Billet-8-High-Gain-Radio-Antenna-Ford-Chevy-GMC-RAM-Truck-RECON/172281232465?epid=2205191801&hash=item281cc2fc51:g:dzMAAOSwgotcQfuS
Sik asf I proudly got gapped by it
What did you use up front to get to 7 inch and not have a shit load of camber
Jorge Lozano it’s on 2” lowering spindles and the springs are cut quite a bit. No camber adjustment yet
@@CGOD thats crazy i lowered mine to 6 and had insane camber
This one has some camber but it’s not too noticeable. Helps with turning and since we aligned the toe it shouldn’t wear the tires too fast
@@CGOD how does it ride with the cut springs? I'm thinking of cutting my djm springs to get another 2" drop
It rides pretty good, the DJM springs would be better I’d say
How did you extend the gas tank fuel line ?
Jorge Lozano we just used fuel lines and hose clamped them to the original lines
What tire size you got bro
the lazy boy this is 275/30/24 all around
@@CGOD thank you