2011 sr5 was the opposite but was helpful the connection I try out before do the final attachment so it was just 1 min to adjust the right color wire thank you
Bless you for making this video. I'm glad I got the plug and play harness so I didn't erroneously start splicing wires. Your instructions were backwards for my 2008 Tundra Doublecab limited but I couldn't have figured it out without you.
Thank you for the video. Yours is the only one that I found that shows the same plugs and wires that mine has. I was going crazy trying to figure out how to hook it up. Not even pop and locks website has the correct instructions. Very aggravating. Thanks again!
Thank you for putting up a video. Today I install power lock tailgate and using your video for installation. It is working straight out perfect. Thanks
Worked like a charm on my 2011, saved me a bunch of time! But the wiring was reverse for me, blue to blue, white to green. If anyone has issue where the unlock bottom will lock and lock button will unlock, just flip the wires around!
Thank you for this comment, this is my issue as well, lock unlocks and unlock locks. Also I have an aftermarket cheap tailgate handle (had to replace the original)…. The actuator skips over the little lever on the lock mechanism…. Solution was to wedge something under the actuator to the right of the bolt (when looking down at the actuator)…. Because when tightening the bolt down the actuator arm lifts slightly higher, the wedge prevents this from happening when tightening down the bolt
@@ocin311 ahh yes I ran into this too! I had to drill a tiny hole in the actuator, as there is a little plastic piece sticking out on the tailgate handle which causes the actuator to lift as you tighten. I wonder if I also have an aftermarket handle, or perhaps any handle will have this issue?
Thanks for the video. Looks like the harness for 2007-2010 are the same. The instruction that came with the kit were for newer tundra which didn’t match mine. I got it working after watching your video. You rock!!!
Myself and others had a different experience. Did you try following the instructions it came with? Or another video? If you solved your issue you should post the solution.
On my 2007 the lock and unlock are reversed as well. Blue goes with blue and green goes with white. Thank you for this video though it is the ONLY one as far as I know and super helpful.
Someone out there needs to thank you. I looked high and low for a Tacoma video. Only found 1. Haven’t seen too many Tundra videos either.
Thank you this worked for 2009 tundra!
2011 sr5 was the opposite but was helpful the connection I try out before do the final attachment so it was just 1 min to adjust the right color wire thank you
Bless you for making this video. I'm glad I got the plug and play harness so I didn't erroneously start splicing wires. Your instructions were backwards for my 2008 Tundra Doublecab limited but I couldn't have figured it out without you.
Thank you for the video. Yours is the only one that I found that shows the same plugs and wires that mine has. I was going crazy trying to figure out how to hook it up. Not even pop and locks website has the correct instructions. Very aggravating. Thanks again!
Thank you. You helped my finish my install
Thank you for putting up a video. Today I install power lock tailgate and using your video for installation. It is working straight out perfect. Thanks
Worked like a charm on my 2011, saved me a bunch of time! But the wiring was reverse for me, blue to blue, white to green. If anyone has issue where the unlock bottom will lock and lock button will unlock, just flip the wires around!
Thank you for this comment, this is my issue as well, lock unlocks and unlock locks.
Also I have an aftermarket cheap tailgate handle (had to replace the original)…. The actuator skips over the little lever on the lock mechanism…. Solution was to wedge something under the actuator to the right of the bolt (when looking down at the actuator)…. Because when tightening the bolt down the actuator arm lifts slightly higher, the wedge prevents this from happening when tightening down the bolt
@@ocin311 ahh yes I ran into this too! I had to drill a tiny hole in the actuator, as there is a little plastic piece sticking out on the tailgate handle which causes the actuator to lift as you tighten.
I wonder if I also have an aftermarket handle, or perhaps any handle will have this issue?
Thanks for the video. Looks like the harness for 2007-2010 are the same. The instruction that came with the kit were for newer tundra which didn’t match mine. I got it working after watching your video. You rock!!!
Thank you
The guidelines say keep it respectful, Sir.
Thank you for your help
I wired my 2010 per this video and my lock/ unlock are reversed.
Myself and others had a different experience. Did you try following the instructions it came with? Or another video?
If you solved your issue you should post the solution.
On my 2007 the lock and unlock are reversed as well. Blue goes with blue and green goes with white. Thank you for this video though it is the ONLY one as far as I know and super helpful.