The Ultimate Guide to Installing Engineered Hardwood Flooring
ฝัง
- เผยแพร่เมื่อ 16 มิ.ย. 2024
- This DIY engineered hardwood floor install tutorial is all about how to install engineered hardwood flooring from start to finish. This DIY wood floor install shows the entire process of how to install wood flooring properly with a flooring nailer and how to glue down engineered wood flooring properly on concrete. Plus see how you can install Engineered Wood flooring on stairs. Bring Your Own Tools (#BYOTools 213).
Huge thank you to Flooring Direct Warehouse for being our sponsor this week. Check out their amazing product line HERE: bit.ly/byot_nail_down
Apparel List:
-Georgia Boots (20% off with "BYOT"): www.georgiaboot.com/
-BYOT Shirt: bit.ly/36tsgE0
-Knee Pads: amzn.to/3y2T0XT
-Full Face Respirator: amzn.to/3yP2Lsp
Material List:
-Wood Flooring (Canyon): bit.ly/byot_nail_down
-Eco Underlayment: thd.co/3NYtgEC
-Blue Painters Tape: amzn.to/3tgKoLF
-Flooring Adhesive: bit.ly/3OIZ2WH
-Pin Nails: amzn.to/3MtlDoe
-Roberts Wood Putty: amzn.to/3EDnhkm
Tool List (Amazon Links):
-Fein Shop Vac: amzn.to/3I5sbY3
-Floor Installation Kit amzn.to/3hs3E1B
-Oscillating Multitool amzn.to/2ZQqSsC
-Rubber Hammer amzn.to/30xK4dN
-Table Saw amzn.to/2X3uN2i
-Chop Saw amzn.to/2VDC4W5
-Carpenter Square amzn.to/2XHVADw
-Tape Measure amzn.to/2Q6axKS
-Grinder: amzn.to/3ENqjCp
-Grinder Shroud: amzn.to/3KdHGh0
-Grinder Cleaning Wheel: amzn.to/3MuC1oh
-Tread Template: amzn.to/3OvXgYE
-Pin Nailer: amzn.to/3k7xFHs
CHAPTERS:
0:00 - Intro
3:56 - How To Install A Hardwood Floor Underlayment
4:37 - How To Install Engineered Hardwood Flooring
16:04 - How To Install Custom Floor Vents
17:19 - How To Prep Concrete For Glue Down Flooring
19:05 - How To Glue Down Wood Flooring To Concrete
27:33 - How To Prep Stair Before Installing Treads
30:34 - How To Install Stair Treads And Risers
42:50 - Finish Shots
MUSIC from www.endlessnoise.com/ & www.chernebeats.com - แนวปฏิบัติและการใช้ชีวิต
Exactly what I wanted and needed out of a video for engineered hardwood install. Thank you.
43 minutes video! It's Christmas morning! 🤣
Haha! Enjoy and thanks for watching as always :)
This is great timing. I have installed vinyl plank before but didn't really know how to install wood flooring on a concrete slab. Thanks for another great video!
Amazing to hear. Thanks so much for watching and hope the video helps.
WOW!!! This is an amazing job! It looks beautiful and so well done. Congrats!
Truly appricate the kind words and all the support.
Great work as usual, love it. Thanks for sharing your skills. You make my day.
LOVE hearing that and thanks so much for watching and all the support Nigel.
Am I having de javu? I remember this video from a few years ago just edited a bit differently. Anyways. Great video. I watched the whole thing again. Great flooring choice and perfect installation. Thanks again Brett!
Thanks so much for mentioning that Roger and YES you are 100% correct. This is an old video series but it was broken up into three different videos and I wanted to repurpose it to be one cohesive video structure so all these valuable tips are in one video. FULL disclosure to be honest with the BYOT audience is that I'm having some difficulty with a current project that is taking longer then expected to complete. Don't want too many weeks to go by without a post so I occasionally repurpose old videos that deserve a re-edit in order to make a more cohesive video structure like this one for larger projects. Hope that makes sense and thanks so much for watching and all the support.
@@BYOTools Good thinking. I remember now the 3 parts and it worked well making one video combining them all. Well done and I love watching them all. And your voice is NOT annoying!😁👍
Great video!! Very informative and well paced.
Thanks so much for watching and all the support. Keepup the great work on your channel as well.
What happens if you were to have floated the floor instead of gluing?
looks awesome!! And your videos are so enjoyable to watch :)
Thanks so much for all the support and kind words. Keep up the great restorations on your channel.
I like this working I have 10 year's experience UAE now I need job
Nice job
Would you glue and staple 1"x12"x16' pine tg on wood subfloor over crawalspace or vapor barrier w staples? Great work!
“With staples you get twice the penetration for a single hit… and I appreciate that” starting at 10:36 .. mastery
Hey! I live in Long Branch, NJ and was impressed with your work. In 2023, I founded my sand and install flooring company, IAC - American Floor, and am seeking advice on how to expand my business and find more job opportunities. I am open to any suggestions or guidance you can offer. Thanks in advance!
my 2 cents:
Don't buy the $4 pry bar from harbor freight if you value your eyesight
Use the scrap piece/ oscilating tool to cut the door jamb too, not just the casing, then slide floor under.
You can use the rubber end of the mallet to send the board home, although you used prefinished floor so I understand the precaution. But this goes for closing gaps near walls too.
Once you chalk the line to get your initial run, you can screw down a straight 2x4 or 2x6 to that line on the subfloor to be sure the floor stapler can't move the board off your line.
Then after a few more runs past that you can unscrew the 2x, put underlayment down and put a spline (a piece of tongue you put in the stair tread) in the groove and go the other direction with the floor stapler until you're too close to the wall.
If you need to make splines with your table saw they're about 3/16 thick and 3/8 wide.
Good video!
Where did you buy this material?
He got it free.. This is an AD....
here's a link to the exact product I used on this project: fdwflooring.com/product/antique-canyon/
Yes they are the sponsor of the video but did you watch and learn anything? You can utilize this video when installing many different engineered hardwood flooring products out there. Don't discount FDW for actually supporting creators. Thanks for watching.
🙏👏👍💪
Thanks for always being there and watching Alain.
I've never heard someone call baseboards, "wall base" before.
Where do you live? pretty common where I live.
@@BYOTools upstate NY, but I also lived in TN and only ever heard baseboard. Googling wall base though brings up a totally different style of trim, that I kind of like.
Aria vents will burn out your furnace fan motor; you will not get proper CFM without too much pressure. They look good but they are no good for HVAC systems edit: they know go by Fittes
Thanks for mentioning that. Has there been a comparison test that can be referenced?
@@BYOToolsLet me preface that I'm not an HVAC guy, first youtube video that I found with analysis was th-cam.com/video/1hfmbLiL0i4/w-d-xo.html. If your system was designed from the ground up with it in mind, maybe it'd be fine? They look absolutely phenomenal, but for my own house, I had to go a different route.
omg it's the "heighth" guy again lol
I am about to be 40 and just found out that isn't a word lol..
I have two damaged fingers that ached with every shot of the table saw used without a push stick. Please be careful, complacency can bite back.
100% agree and must be extremely careful when cutting boards on a table saw. Thanks for watching and mentioning this.
Per manufacturer and the wood flooring association, any engineered floor has to be glued down and stapled if it's over 5" wide, using the glue assist meathod or full glue down...
Not sure you need to glue if you are laying a "floating floor". Also considering this chap does not allow for expansion, he is demonstrating a total lack of knowledge.
@@stewartgranger7674 pretty sure most if not all manufacturers say you can not float a wide plank enginerered floor.
'Promosm'
You use words like "exactly", "perfectly", "extremely", and "very" wayyyy too often, you should try to cut down on them