This is a great video. Thank you for sharing. I have a JD 435 and the twine arm will not engage automatically. I have to manually engage the twine arm by pulling the outside lever no matter the bale size. I’ve been trying to figure out how to get it to work properly for a while with no luck. Do you know what could prevent it from tying automatically? Following your video instructions, I can now tell that the manifold plunger is not lifted up but I’m not sure what to adjust to make it rise.
How much air would you suggest blowing in? I have a 530, almost exact same twine system. The pump ram low on fluid friday night, and now the twine arm won't move. Anyone have any suggestions? I think I've narrowed it down to either the pump or the needle valve
@@beeffarmer8576 that is a good possibility. I’ve installed pumps from an 80’s Chevy 350 engine. Swap the relief out of the original one and put it in the new one.
We have JD 430 baler that randomly locks up during baling and shuts off tractor. You can dump bale and start over normally, but today it would get about 4 foot bale and lock up and shut tractor off. Have you had any experience with this issue?
Im stuck with a 430 I bought, it hasnt run in a few years. The pump looks new but was dry, try bleeding the hydraulics and managed to do so now the arm cycles but even after hitting the stop button the arm keeps traveling forward until the gear comes out of the rack thats actuated by the cylinder.. I tried sending you a dm but no luck doing that on youtube. is there any way I could reach you over the phone? Im in Mexico but can call international no problem.
What an amazing guy we were broke down in Ont canada with our 430 jd baler he called personally and led us to the fix
Thank you so much Brian
@@KenPrince-v9o thank you
Thank you i have a 530 very good video i was having trouble with my tie arm not returning.
Thanks for your insight on the 430. We are running one in Arkansas and she is holding tight!
This is a great video. Thank you for sharing. I have a JD 435 and the twine arm will not engage automatically. I have to manually engage the twine arm by pulling the outside lever no matter the bale size. I’ve been trying to figure out how to get it to work properly for a while with no luck. Do you know what could prevent it from tying automatically? Following your video instructions, I can now tell that the manifold plunger is not lifted up but I’m not sure what to adjust to make it rise.
Can you PM me in messenger.
Brian Craig
@@BrianCraig870 can you dm me somehow to discuss a 435 kinda lost on it
@@jacobfischer5728I’m not sure how to DM you
How much air would you suggest blowing in?
I have a 530, almost exact same twine system. The pump ram low on fluid friday night, and now the twine arm won't move. Anyone have any suggestions? I think I've narrowed it down to either the pump or the needle valve
@@beeffarmer8576 a good shot of air will usually get it going as long as the pump is good.
Ill try that. Thanks for the advice! @@BrianCraig870
@@BrianCraig870 tried air and no luck. At this point i think the pump may be shot.
@@beeffarmer8576 that is a good possibility. I’ve installed pumps from an 80’s Chevy 350 engine. Swap the relief out of the original one and put it in the new one.
We have JD 430 baler that randomly locks up during baling and shuts off tractor. You can dump bale and start over normally, but today it would get about 4 foot bale and lock up and shut tractor off. Have you had any experience with this issue?
Is the tailgate opening causing the baler to stop baling?
What kind of fluid goes in a 430 John Deere baler?
I use hydraulic fluid in my system
Im stuck with a 430 I bought, it hasnt run in a few years. The pump looks new but was dry, try bleeding the hydraulics and managed to do so now the arm cycles but even after hitting the stop button the arm keeps traveling forward until the gear comes out of the rack thats actuated by the cylinder.. I tried sending you a dm but no luck doing that on youtube. is there any way I could reach you over the phone? Im in Mexico but can call international no problem.
th-cam.com/video/xbiERetxHKA/w-d-xo.htmlsi=v2bdwayymXs0qvXO this might help you?
8599836744
Can you PM me in messenger and I’ll try to diagnose it for you. Brian Craig.