@@TheRealMonnie k... We're talking about simple miters! it is not freaking artistic expression... There is a difference between being creative and being ignorant...
Monnie Holt 😂😂 Do you know the reason we do certain things the same way for centuries? Because it’s the proven to be the best way. Ever heard the phrase, no need to reinvent the wheel? That applies here.
You can also measure down from your cutting edge the diameter of the pipe. A 45° cut will always be the diameter of the pipe. 2" pipe; measure down 2" on both pipes. 4" pipe same thing.
Good tip! A 45° angle is just the classic rise-over-run equilant of 1unit rise/1 unit run. This comes from geometry and the equation for a line: y = mx +b, where m is the slope of the line and is defined as: (change in y coordinate)/(change in x coordinate), in other words rise/run.
@@jeremiahmccutcheon3234 you're bigger pipes are usually cast iron and concrete line for water can't be welding when you got concrete and just destroys the concrete then you get rust you have to use a mechanical joint even if it wasn't concrete line can weld cast iron but it would destroy if it was a concrete line which all water lines are
@@mikesmithey1892 actually I am speaking on industrial pipes like at any refinery ,pipeline, chemical facility. Most of those pipes are stainless , incomel monel. Exitic metals. Definitely not cast iron.
That is handy when using an angle grinder to cut the pipes for right angle joints like what is done in the video. Of coursse doing so would be esier and faster on a miter saw if one has it.
Not everyone has miter saw smart guy. This video is useful for people with angle grinders and simple tools and for small projects OR when the pipe is too big for the miter saw (didnt think about that, did ya?). The point is to display practical and creative skills thought out of necessity. By your logic "everyone" can just use a pipe guide and mark it up smoothly and cut up everything in one go.
Nice way to approximate the layout. ALTERNATIVE With those two tubes held in the magnetic square, one straight cut across both ends simultaneously, by disk grinder or portable band saw, will yield a joint mitered to give a perfect 90 degrees. Even if your chop is not at a perfect 45, the error will cancel out on assembly, giving a perfect right angle. No layout, one cut, done.
That's the first thing I thought in the first few seconds of the clip. You would need a clamping jig that holds the two pipes perpendicular. That little red magnetic square won't do it because of two reasons: magnets don't hold as strongly as an actual clamp, and that square extends all the way to the end of the tubes, the clamping jig would have to grab the tubes a little further from the ends just in case the saw comes too close (gotta allow about 1/8 for the kerf). Still though... just get a bloody miter saw already.
Am I missing something here? If you make a 45 degree cut in a round pipe, and rotate 1 side through 180 degrees bringing the 2 cut edges together you form a 90 degree angle just like this. Exactly like this. No template. No marking out. If you want a 60 degree corner you make a 30 degree cut and so on. Just saying.
@@markharmon4963 all the time. I am a fitter/fabricator and 99% of the time I’m in the field working on a job, I have no access to a chop saw or mitre band saw, so everything is done with a grinder. Maybe Alan has never done field work before, so he assumes it’s just as easy as setting up a saw to cut whatever angle he wants. Knowing how to lay out cuts on the material is a very valuable skill.
A lot of people say to use a chop saw, ok that may work until you are working on and modifying existing pipe work with little room to move And every cut is by hand, this is as good a way as any, thanks for posting..
That is a very cool method, altho very complicated, i like to just stack the pipes on top of each other at 90 degrees and cut thru both at the same time
@Roger Paul, astute, and the voice of experience. I just wrote something similar. The key to your method is shown in the first scene; the mag square. One chop across both ends at the same time will give a perfect 90, self correcting for small errors in eyeballing the cut at 45 degrees
So, if one needs to join pipes of diameter smaller than 10" and one doesn't have 'specialised tools' readily available, you recommend "don't even try"?!
@@Fordgroup00 Regardless of cost, is a 'chop saw' not designed for the specific and sole purpose of cutting at precise angles?! Can a 'chop saw' be used to lop the top off a 30ft tree?! Is a 'chop saw' not considerably more 'specialised' than what was used in the video - to successfully achieve the same result that a 'chop saw' would produce?! I'm at a loss to understand why soooooo many people -predominantly Yanks - have got their frilly pink knickers in a twist over my use of the word 'specialised'. Maybe you all need to consult a dictionary before going off on a peurile rant. (For your assistance - 'specialised tool', a tool designed and developed to perform one particular task.) Regardless of what tool would perform any task faster than 'basic' (I hope that word doesn't trigger more aggression) tools and regardless of how one describes that tool, if it's not available to you at the time and location you would like to have it, are you just going to sit on your arse and cry?! This video demonstrates a simple, very basic, procedure to resolve a, very simple, problem using VERY basic tools. So, as we say in Aus, pull up your pants and give your mouth a go - ie stop talking out of your arse. Over and out.
Sure, if you 100% of the time have access to a mitre saw. The fishing boats I used to work on had minimal tools, never a mitre saw. I like to learn new ways of doing things I already know how to do. You never know when it might come in handy.
@@vandalsgarage it's called a fucking speed square. If you don't own any tools how are you going to weld anything without a fucking welder? Just fold a piece of paper diagonally and you have a more accurate square than 99% of the Chinese junk they sell at Homeboy Depot.
Mitter circular saws work only close to half the diameter of the circular saw but if the width of the object material is bigger than the diameter of the circular saw then it doesn't cur all the way through but this is perfection of another way of cutting a 90 on any pipe size, that is if the craftswo/man has the right saw and or other tools if not.
I cut 35 pieces of 3" pipe at 45-degree angles and saw this was still life hacking a "never told before trick". There is a reason why it was never told....
I’ve made that cut freehand with a torch thousands of times. Mostly 2 3/8” drill stem. Many miles of pipe fence on my ranch. BUT, your method is an excellent idea for the beginner!! TEXAS!
I only scrolled down a couple of comments but, the simplest solution is to get a copy of the Pipefitters handbook and wrap a piece of material around the pipe, cut the material that is now the circumference of said pipe. Fold it and unfold it then use the measurements on it, connect the lines, cut it out, and you've got a template for later use.
You could save yourself the work of making the cutout and just use the end of one pipe to mark the other and vice versa. You could also take a hole saw or something of similar radius to roll it around the curvature and mark the cut better. Either way, this method is just an approximation, so it doesn't matter much.
The subject of this video is not complex or hidden. It addresses how to DESCRIBE a 45 degree angle on pipe / tubing without using 'specialised' / 'conventional' tools. The process / method works regardless of the material from which said pipe / tubing is manufactured and / or the diameter of said pipe / tubing. For whatever reason, the piping / tubing might not actually be cut. A 'cold saw' is designed and intended for cutting METALS - including in pipe / tube form. If the pipe / tubing one intends to cut is made from flexible plastic or rigid PVC, how doe a 'cold saw' help me to DESCRIBE the angle to be cut?! Do you recommend using a 'cold saw' for actually CUTTING flexible plastic and / or rigid PVC pipe / tubing?! Do you know some alternative process / method for DESCRIBING a 45 degree angle on pipe / tubing - without resorting to using 'specialised' / 'connventional' tools? If so, please post a video so that we may ALL be educated.
@@trueaussie9230 what are you talking about? This video is obviously about cutting metal. And yes a mitre saw would make it easier and much much quicker.
Honestly I've cut my share of pipe in the past but I'd never thought to do it like this! That was sooo cool!!!! I'm going to have to remember this little trick the next time I need to do some pipe cutting. Thank you for a very informative video Budak. You now have a new subscriber and I hope to see more of your amazing videos.
I've got some 6 inch stainless pipe that needs cutting at a 45. Thanks heaps. And nevermind the haters that can't understand that learning different ways to do things has immense value!
45° is a special angle. Always equal rise equal run. Measure down whatever the width of the material is and go straight across for a 45. However, using the welding magnet is a nice little trick that I need to start using, thanks for that!
Plenty of nay-sayer jack holes here. Yes know-it-alls, we can use a miter saw. But there's more than one way to skim a cat. Maybe a guy doing a project doesn't have a miter saw, this can be his next best option. Quit hating people for not doing things your way. And this was a very cool video!! I want to try this to, maybe give my saw the afternoon off!!
Thanks, neat trick will have to put it into my notes. I had made a fixture for different angles, but this would be easier and faster to set up for a cut now and then!
Yep , I'd say just get a chop saw if you're going to make a bunch of angle cuts , cutting out a bunch of circles trace them onto the pipe and cut just seems a little too ocd for me . Really I can use a speed square and eyeball angles within reason and make up any imperfections with a mig . And if I needed the perfect cuts , like for no filler rod if I learned TIG (I want to soon) , I'd just go the extra mile and buy a chop saw if I didn't have one .
@@trueaussie9230 I don't mean to dismiss your problem , but if you have a welder and other fab tools , then you should invest in a cheep chop saw . Even a hack saw can make 45's . The main thing is having a decent jig design . And if you are MIG welding or stick you can repair any imperfections from the cut . But if you have a clean place in your fab area to play around with paper and cut outs ? Knock yourself out . I don't know your situation , but when you are a long way from a town you need to work on increasing your tools , unless you're just hobbying , then I guess the circle is a good thing .
Милый человек хоть я вас не знаю.Мы не знакомы .Но по отзывам вы светлый человек И просто хочется сказать .Будь просто счастлив .Спасибо за все что вы делаете для людей .Здоровья вам на долгие годы.Надежных и преданых друзей .Что бы вы всегда были нужны кому то .И вас всегда ждали на этом большом шаре .Всех вам благ .Спасибо за вашу проделанную работу .Потраченные силы нервы время .Так держать.Низкий вам поклон .Респект и уважение
Used for big pipe, never seen it done on anything less than 100mm. Even then the cardboard template isn't used. Just mark down to the same measurement as the diameter.
Another good method to have if you don’t have anything else to use you can use a big leaf in place for this. The point he is making here this is a method to get professional joints. No excuse for shit work. Thanks for posting!!!!!
Find the middle of the magnet and draw a line then push the pipe until the line matches with the outer side of the pipe, the one that isn't on magnet much easier this way in case you don't carry saw miter in the field or having one in your shop.
@@trueaussie9230 a chop saw is cheap and very basic. Anyone that does any type of metal work at all, especially someone that is cutting and welding tube will have one.
@@JohnDoe-ud2cc So, are you saying when someone finds, for the first time in their life, they need to cut metal pipe / tubing a 'chop saw' will just magically appear - regardless of where they're located at the time?! Are you saying that, simply by OWNING a 'chop saw' it will always make itself readily available to you wherever you're located at the time of needing it?! Damn. That's some seriously MAGIC tool. (Have you NEVER found yourself in a situation where a tool that you OWN and need for the situation you unexpectedly find yourself in, is not readily available to you - perhaps because it's in your toolshed and you are 50 miles away from it?!) The technique demonstrated - ie for DESCRIBING a 45 degree angle on pipe / tubing - is applicable regardless of the material from which the pipe / tubing is made. So, for someone who works with PVC pipe / tubing and NEVER works with metal at all, how does that magic 'chop saw' help them?! Will it still magically appear to assist with DESCRIBING the 45 degree angle. (I don't know about you, but I wouldn't recommend CUTTING PVC with a 'chop saw'.)
@@trueaussie9230 man did I touch a nerve, a bit sensitive are we. I can come back and use your same argument back on you. What if a person doesn’t have a cut off wheel or grinder, a welders 90 magnet, a welder, paper, a sharpie, or even electricity for that matter.
@@trueaussie9230 bro you’ve commented to every person that mention any type of tool other than a pencil. Just let it go, let them miss the interpretation.
Recently I had to make such cuts but miter saw broke. I marked similarly, the marking was good but the problem was that I couldnt cut so straight with handheld grinder. Even best marking template wont help you when your hand is not trammed perfectly...
@@Exotiq. what about if you dont have pencil or pen? Or you dont have paper? Oh wait, what about if you dont have saw 😂 That plastic box is cheaper than your saw, so what an excuse? You have welder there to weld 45 degree iron, bur you dont have mitter saw? At least you have 45 degree guide. This video is nonsense and you defending the nonsenesnes. Welcome to the world 🤣
Unless you have the proper tools and are only cutting two. This is quite useful and faster if you're cutting plenty of pipes at right angle, since you have a template already. You dont even need the magnet.
@@trueaussie9230 You could literally accomplish this with a mitre gauge and a hand saw, both of which are not specialized. You can make a mitre gauge in half the time it takes to use this method to mark the pipe. This is overly complex for no reason other than getting views on TH-cam. Probably one of the dumbest methods I’ve ever seen to accomplish a 45 degree cut.
Nice work, but no need for paper, and all this time, just calculate the width of the pipe and start cutting the pipe to the other edge at angle 45, you'll get the same result.
Your magnet already has the necessary 45ﾟ angle obviously.. If you attach your tube and let it overhang overhang the edge of the table you can simply use the table edge to scribe your line without having to do any of the paper and marking Tricks
It never ceases to amaze me how many people do not understand simple 45° angles.
Tim tel
Yep
That's exactly what I was thinking. Simple and quick lol
Yup... I thought it was going to be some weird 3 piece shape and angles... nope ..nothing a Harbour freight mitre gauge won't solve
Username checks out
That is by far the most complicated method for cutting a mitre I’ve ever seen.
You telling me, too much work
My chop saw: 😴
Creativity is the mother of invention. You keep doing things the same old way and watch your creativity diminish.
@@TheRealMonnie k... We're talking about simple miters! it is not freaking artistic expression... There is a difference between being creative and being ignorant...
Monnie Holt 😂😂
Do you know the reason we do certain things the same way for centuries? Because it’s the proven to be the best way.
Ever heard the phrase, no need to reinvent the wheel? That applies here.
You can also measure down from your cutting edge the diameter of the pipe. A 45° cut will always be the diameter of the pipe. 2" pipe; measure down 2" on both pipes. 4" pipe same thing.
aye, that's what I was gonna comment!
Good tip! A 45° angle is just the classic rise-over-run equilant of 1unit rise/1 unit run. This comes from geometry and the equation for a line: y = mx +b, where m is the slope of the line and is defined as: (change in y coordinate)/(change in x coordinate), in other words rise/run.
Yes that would be the normal way, or you can waste your time making a paper template
@@SparrowHawk183 Buzz kill, you had to bring in math.....lol
@@seymourwrasse3321 math is OK, as long as its numbers, but the guy has to bring in the letters. Damn nerds and their letters.
I could see this being useful on larger diameter tubes/pipes that won't fit into a mitre box or saw.
You can make a miter box faster than this method, and use a hacksaw
Pipes that are so big that won't fit in a miter box usually use a mechanical joint
Not necessarily mechanical joints for larger pipes if that was the case we wouldn’t need pipe welders
@@jeremiahmccutcheon3234 you're bigger pipes are usually cast iron and concrete line for water can't be welding when you got concrete and just destroys the concrete then you get rust you have to use a mechanical joint even if it wasn't concrete line can weld cast iron but it would destroy if it was a concrete line which all water lines are
@@mikesmithey1892 actually I am speaking on industrial pipes like at any refinery ,pipeline, chemical facility. Most of those pipes are stainless , incomel monel. Exitic metals. Definitely not cast iron.
Let me get this straight. Play with paper. Mark up the end of the pipes. Cut both pipes at a 45° angle on a miter saw. ✔️
That is handy when using an angle grinder to cut the pipes for right angle joints like what is done in the video. Of coursse doing so would be esier and faster on a miter saw if one has it.
Not everyone has miter saw smart guy. This video is useful for people with angle grinders and simple tools and for small projects OR when the pipe is too big for the miter saw (didnt think about that, did ya?). The point is to display practical and creative skills thought out of necessity. By your logic "everyone" can just use a pipe guide and mark it up smoothly and cut up everything in one go.
Nice way to approximate the layout.
ALTERNATIVE
With those two tubes held in the magnetic square, one straight cut across both ends simultaneously, by disk grinder or portable band saw, will yield a joint mitered to give a perfect 90 degrees. Even if your chop is not at a perfect 45, the error will cancel out on assembly, giving a perfect right angle. No layout, one cut, done.
I was only six days late, should have read all the posts. I agree with ya tho !
That's the first thing I thought in the first few seconds of the clip. You would need a clamping jig that holds the two pipes perpendicular. That little red magnetic square won't do it because of two reasons: magnets don't hold as strongly as an actual clamp, and that square extends all the way to the end of the tubes, the clamping jig would have to grab the tubes a little further from the ends just in case the saw comes too close (gotta allow about 1/8 for the kerf). Still though... just get a bloody miter saw already.
@@paul_fredrick, yer a geometrician!
My old school buddy taught me your technique
We have a winner!!!!
Am I missing something here? If you make a 45 degree cut in a round pipe, and rotate 1 side through 180 degrees bringing the 2 cut edges together you form a 90 degree angle just like this. Exactly like this. No template. No marking out.
If you want a 60 degree corner you make a 30 degree cut and so on.
Just saying.
I'm pretty sure the end result is off a miter/chop saw. Stupid interwebs making up some bullshit content to get us to watch commercials. Cool.
This video was showing you how to use a single square of paper to lay out a 45 degree mitre cut.
Obviously a mitre saw cuts mitres.
@@Turin-Fett Exactly. And sometimes you need a layout before you cut.
@@markharmon4963 all the time. I am a fitter/fabricator and 99% of the time I’m in the field working on a job, I have no access to a chop saw or mitre band saw, so everything is done with a grinder. Maybe Alan has never done field work before, so he assumes it’s just as easy as setting up a saw to cut whatever angle he wants. Knowing how to lay out cuts on the material is a very valuable skill.
Wouldn’t a combination square do the same thing? It’s what I always used to make 45 degree cuts.
I'm more impressed with the stability on that angle grinder. Very, very clean edge.
Coward.
Flap disc off camera probably
It's always good to know more than one way to solve a problem.
i just love it when they don't talk. so peaceful
A lot of people say to use a chop saw, ok that may work until you are working on and modifying existing pipe work with little room to move And every cut is by hand, this is as good a way as any, thanks for posting..
Almost anybody can purchase tools, but hand Skills can’t be purchased. Great job! In showing us another skill of yours 👍🇨🇦
You have to earn skills.
That is a very cool method, altho very complicated, i like to just stack the pipes on top of each other at 90 degrees and cut thru both at the same time
how do you hold them while cutting?
@@Sunrayman123 they have these cool new things called clamps.
@@davedammitt7691 😅
@Roger Paul, astute, and the voice of experience. I just wrote something similar. The key to your method is shown in the first scene; the mag square. One chop across both ends at the same time will give a perfect 90, self correcting for small errors in eyeballing the cut at 45 degrees
Wow, that's all I can say, many thanks for taking the time to make this clip. This is really handy information. Triple thumbs up.
At your service sir 😊😄👍
Keep this technique for large pipe projects more. In case you need to do this with 10 or 12 inch pipe.
So, if one needs to join pipes of diameter smaller than 10" and one doesn't have 'specialised tools' readily available, you recommend "don't even try"?!
@@trueaussie9230 one Aussie to another That's what he is saying!!!
@@trueaussie9230
A chop saw that cuts 45d is not a specialty tool 😂
@@Fordgroup00
Regardless of cost, is a 'chop saw' not designed for the specific and sole purpose of cutting at precise angles?!
Can a 'chop saw' be used to lop the top off a 30ft tree?!
Is a 'chop saw' not considerably more 'specialised' than what was used in the video - to successfully achieve the same result that a 'chop saw' would produce?!
I'm at a loss to understand why soooooo many people -predominantly Yanks - have got their frilly pink knickers in a twist over my use of the word 'specialised'.
Maybe you all need to consult a dictionary before going off on a peurile rant.
(For your assistance - 'specialised tool', a tool designed and developed to perform one particular task.)
Regardless of what tool would perform any task faster than 'basic' (I hope that word doesn't trigger more aggression) tools and regardless of how one describes that tool, if it's not available to you at the time and location you would like to have it, are you just going to sit on your arse and cry?!
This video demonstrates a simple, very basic, procedure to resolve a, very simple, problem using VERY basic tools.
So, as we say in Aus, pull up your pants and give your mouth a go - ie stop talking out of your arse.
Over and out.
Great👍
That seems a hundred times more work than a mitre saw
Sure, if you 100% of the time have access to a mitre saw. The fishing boats I used to work on had minimal tools, never a mitre saw. I like to learn new ways of doing things I already know how to do. You never know when it might come in handy.
@Brandon Rivera i wouldnt even do that, id just use the piece to place the mark. no fucking around measuring or little bit of paper
@@vandalsgarage it's called a fucking speed square. If you don't own any tools how are you going to weld anything without a fucking welder? Just fold a piece of paper diagonally and you have a more accurate square than 99% of the Chinese junk they sell at Homeboy Depot.
There is a tool for this called a chop shaw lol
Way Faster!!!
Mitter circular saws work only close to half the diameter of the circular saw but if the width of the object material is bigger than the diameter of the circular saw then it doesn't cur all the way through but this is perfection of another way of cutting a 90 on any pipe size, that is if the craftswo/man has the right saw and or other tools if not.
Well for those that don’t have one yet this is a good alternative lol
A square...
This method is way more affordable. Next time the chop saw goes out and only a few cuts to go, now you have an affordable way to finish the job.
People are talking shit but..... Everybody doesnt own a chop saw. I own a welder but no chop saw. I really appreciated this video. Thanks.
Well done, an excellent method for a close fitting at 90 degrees
I cut 35 pieces of 3" pipe at 45-degree angles and saw this was still life hacking a "never told before trick". There is a reason why it was never told....
I’ve made that cut freehand with a torch thousands of times. Mostly 2 3/8” drill stem. Many miles of pipe fence on my ranch. BUT, your method is an excellent idea for the beginner!! TEXAS!
0p
I've done the same with the torch. Your torch skills are probably better than mine so I migrated to a grinder and free-handed it.
Все гениальное просто мужик благодарочка, помог, здоровья тебе. Пламенный привет с МОЛДОВЫ !
Wow. What an extra long technical way to do a simple job!!
I only scrolled down a couple of comments but, the simplest solution is to get a copy of the Pipefitters handbook and wrap a piece of material around the pipe, cut the material that is now the circumference of said pipe. Fold it and unfold it then use the measurements on it, connect the lines, cut it out, and you've got a template for later use.
You could save yourself the work of making the cutout and just use the end of one pipe to mark the other and vice versa. You could also take a hole saw or something of similar radius to roll it around the curvature and mark the cut better. Either way, this method is just an approximation, so it doesn't matter much.
Thanks for the opinion 👍
A pen-mark helps you design and measure before you are ready to cut.
..thanks for sharing this, mate.. i do really need this knowledge for my new job..
At your service sir 😊😄👍
Get yourself a cold saw with adjustable angle. Everything will be easier. Great method and cut though 🤘
The subject of this video is not complex or hidden.
It addresses how to DESCRIBE a 45 degree angle on pipe / tubing without using 'specialised' / 'conventional' tools.
The process / method works regardless of the material from which said pipe / tubing is manufactured and / or the diameter of said pipe / tubing.
For whatever reason, the piping / tubing might not actually be cut.
A 'cold saw' is designed and intended for cutting METALS - including in pipe / tube form.
If the pipe / tubing one intends to cut is made from flexible plastic or rigid PVC, how doe a 'cold saw' help me to DESCRIBE the angle to be cut?!
Do you recommend using a 'cold saw' for actually CUTTING flexible plastic and / or rigid PVC pipe / tubing?!
Do you know some alternative process / method for DESCRIBING a 45 degree angle on pipe / tubing - without resorting to using 'specialised' / 'connventional' tools?
If so, please post a video so that we may ALL be educated.
The rage was one of the best investments I made. Loud, but quick and efficient.
@@trueaussie9230 what are you talking about?
This video is obviously about cutting metal. And yes a mitre saw would make it easier and much much quicker.
@@yallawallahalla
Whatever you say, boss. 😉😆
Oh yea, works great every time!!!!!!👍👍👍👍👍
Me quito el sombrero ante los Buenos Profesionales 👍👏
100 por cento correto o cara é muito ninja milésimo de milímetro certeiro . parabéns rapaz . aqui de Quipapá Pernambuco Brasil .
Honestly I've cut my share of pipe in the past but I'd never thought to do it like this! That was sooo cool!!!! I'm going to have to remember this little trick the next time I need to do some pipe cutting. Thank you for a very informative video Budak. You now have a new subscriber and I hope to see more of your amazing videos.
Thank you my friend 😊👍
this is the best of all the comments i got...❤️
@@bkscreative Any time. I love watching these kinds of how to videos. There are a lot of great ideas that can be used. Keep up the good work.
Use chop saw with metal disc
I've got some 6 inch stainless pipe that needs cutting at a 45. Thanks heaps. And nevermind the haters that can't understand that learning different ways to do things has immense value!
That was I mean, this trick actually work better on a big size pipe😊😄👍
Nice job, thanks for the demonstration.
45° is a special angle. Always equal rise equal run. Measure down whatever the width of the material is and go straight across for a 45. However, using the welding magnet is a nice little trick that I need to start using, thanks for that!
Sir your video super 💐 brilliant easy trick sir 👌👌👌💐
At your service sir 😊😄👍
Hermoso trabajo! LO HIZO SIMPLE Y LÓGICO. MUCHAS GRACIAS POR SU ENSEÑANZA!!!
Thanks Brither.. This video is helper for me...
Plenty of nay-sayer jack holes here. Yes know-it-alls, we can use a miter saw. But there's more than one way to skim a cat. Maybe a guy doing a project doesn't have a miter saw, this can be his next best option. Quit hating people for not doing things your way.
And this was a very cool video!! I want to try this to, maybe give my saw the afternoon off!!
it's also possible that guy only had a small piece of paper and an old grinding machine😂
I mean, I'd just pick my folding rule up and measure it out..
I enjoy it when my catamaran is skimming over the water.
Skim a cat? Does it have a layer of pool sludge on it?
First time I learn such a useful trick… only due to projection of the first tube on the second one… thank for this.
Thanks, neat trick will have to put it into my notes. I had made a fixture for different angles, but this would be easier and faster to set up for a cut now and then!
Your welcome sir 😄
Very nice technique...I like the you did it...perfect tricks...
Thank you my friend ❤️
Impressive !! I have made thousands of cuts for pipe rail
And never thought of the paper template !!
Why? Just cut a 45deg angle. Boom done. This is the same thing with extra steps.
Bhai xenon ka ye product he ise kya bolte he plz batao
Looks like a lot of work.
Yeah. It's easier just to pay someone else to do it - especially if you're stuck in a remote location and your life depends on it. 🤣🤣🤣
Yep , I'd say just get a chop saw if you're going to make a bunch of angle cuts , cutting out a bunch of circles trace them onto the pipe and cut just seems a little too ocd for me .
Really I can use a speed square and eyeball angles within reason and make up any imperfections with a mig . And if I needed the perfect cuts , like for no filler rod if I learned TIG (I want to soon) , I'd just go the extra mile and buy a chop saw if I didn't have one .
@@johnjay5143
And when the nearest 'chop saw' is 500km away?!
You don't get out much, do you?!
@@trueaussie9230 I don't mean to dismiss your problem , but if you have a welder and other fab tools , then you should invest in a cheep chop saw . Even a hack saw can make 45's . The main thing is having a decent jig design . And if you are MIG welding or stick you can repair any imperfections from the cut . But if you have a clean place in your fab area to play around with paper and cut outs ? Knock yourself out .
I don't know your situation , but when you are a long way from a town you need to work on increasing your tools , unless you're just hobbying , then I guess the circle is a good thing .
@@trueaussie9230 Alright , I doubt your life will ever depend on an angle cut in ANY material . Geez , let's drop the drama . Lol
Милый человек хоть я вас не знаю.Мы не знакомы .Но по отзывам вы светлый человек И просто хочется сказать .Будь просто счастлив .Спасибо за все что вы делаете для людей .Здоровья вам на долгие годы.Надежных и преданых друзей .Что бы вы всегда были нужны кому то .И вас всегда ждали на этом большом шаре .Всех вам благ .Спасибо за вашу проделанную работу .Потраченные силы нервы время .Так держать.Низкий вам поклон .Респект и уважение
This was cool. ( cooooool ) Great fun watching. I suppose you can do something similar to notch the tube. tHanks for the video
Good job very nice because of your vlog tutorial I got some knowledge from you
Great tip thank you!
Thank you my friend 😊
Excellent work!
That’s the most painful way ever. 🧐
Dude! I smashed that like button. Thanks for sharing.
Thank you my friend 😊😄👍
It's a good idea, not only this method is useful for round pipes, similar concept would work on any other shapes. Thank you.
So true Dan
Danke, wirklich gut gelöst!
Used for big pipe, never seen it done on anything less than 100mm. Even then the cardboard template isn't used. Just mark down to the same measurement as the diameter.
People have been ‘eyeing’ stuff and getting it real close to right for thousands of years.
Put the tubes into the 90 degree thing, cut across them flat, straight across then roll the tubes over 180.
this was badass, good job
Another good method to have if you don’t have anything else to use you can use a big leaf in place for this. The point he is making here this is a method to get professional joints. No excuse for shit work. Thanks for posting!!!!!
I like it, good method it u was in a tight spot
Find the middle of the magnet and draw a line then push the pipe until the line matches with the outer side of the pipe, the one that isn't on magnet much easier this way in case you don't carry saw miter in the field or having one in your shop.
Looks like a good way to mark rocket fin locations!
Nossa muito perfeito parabéns e obrigado por ensinar
Cara yang sarat manfaat. Trims atas ilmunya 👍👍
If I saw a employee laying out a simple 45⁰ cut like that, I would fire them on the spot.
😂
No shit. Way too much work for a 45 degree cut. Work smarter, not harder.
Your a cheapskate! If you had a chop saw they wouldn’t have to do it this way!
do you have employees ?
Excelente gracias por compartir
Saludos
A chop saw at a 45 degree would do the same thing in about a minute
So, you're dependant on having every ''specialised tool' readily available at all times.
Good luck to you.
@@trueaussie9230 a chop saw is cheap and very basic. Anyone that does any type of metal work at all, especially someone that is cutting and welding tube will have one.
Unless you bought it at Harbor Freight.. yeah, you can guess how I know.
@@JohnDoe-ud2cc
So, are you saying when someone finds, for the first time in their life, they need to cut metal pipe / tubing a 'chop saw' will just magically appear - regardless of where they're located at the time?!
Are you saying that, simply by OWNING a 'chop saw' it will always make itself readily available to you wherever you're located at the time of needing it?!
Damn.
That's some seriously MAGIC tool.
(Have you NEVER found yourself in a situation where a tool that you OWN and need for the situation you unexpectedly find yourself in, is not readily available to you - perhaps because it's in your toolshed and you are 50 miles away from it?!)
The technique demonstrated - ie for DESCRIBING a 45 degree angle on pipe / tubing - is applicable regardless of the material from which the pipe / tubing is made.
So, for someone who works with PVC pipe / tubing and NEVER works with metal at all, how does that magic 'chop saw' help them?!
Will it still magically appear to assist with DESCRIBING the 45 degree angle.
(I don't know about you, but I wouldn't recommend CUTTING PVC with a 'chop saw'.)
@@trueaussie9230 man did I touch a nerve, a bit sensitive are we. I can come back and use your same argument back on you. What if a person doesn’t have a cut off wheel or grinder, a welders 90 magnet, a welder, paper, a sharpie, or even electricity for that matter.
I am so happy I took the time to watch this.
i want my time back
@@tomstiel7576 I was being sarcastic. That 'trick' is about as old as welding.
Do you know how to use a speed square?
yes i know but i dont have it😅
Do you understand the purpose of the video?!
FYI - to demonstrate how one can survive without 'specialised tools'.
@@trueaussie9230 you and your stupid ass "specialized tools" rant. you are an idiot.
@@trueaussie9230 bro you’ve commented to every person that mention any type of tool other than a pencil. Just let it go, let them miss the interpretation.
@@Inpaintballwetrust
Whatever you say, boss.
Super cool...I just use a pipe saddle templates, and steel chop saw.
Why not cut the pipes at 45 degrees, then weld?
Sometimes the pipes cannot be moved. And sometimes you need to mark and measure before you cut.
Will this work for cutting a 180° angle??
LOL
So thankful for my cheap miter saw and the 10 different ways I could think to do this much easier and faster
Recently I had to make such cuts but miter saw broke. I marked similarly, the marking was good but the problem was that I couldnt cut so straight with handheld grinder. Even best marking template wont help you when your hand is not trammed perfectly...
Wouldn’t it just be easier to cut them on a 45?
um get a miter saw set it to 45* clap in pipe cut then repeat. it would take the same amount of time as just marking your layout.
Век живи век учись 👌
th-cam.com/video/TTCPmeMgqFU/w-d-xo.html😍
wihh ga nyangka budak tambuk bikin video gini wkwk, mantap omm, lanjutkan 👍
Terima kasih lur 😄
There is a short and this is a loooong method. 45deg so basic cutting either in carpentry or metalcrafts.
If you know of a better solution - without resorting to 'specialised tools' - please post a video and educate us.
@@trueaussie9230 you really are a turd. how about the rest of the specialized tools? other than yourself. O.o
i remember seeing a saw with a revolving vice -fix the tube, swivel the vice 45deg and cut both tubes, then weld
Now do a 22 1/2°.
Should only take about half the time! 😂
@@c.w.bookout7506 imagine having to do more than one.
Gracias amigo por tu video .
a su servicio señor😊😄👍
You made that way more complicated than it had to be… just set your drop saw at a 45• miter and send it
Yes. I'm not seeing any advantage to all that trouble?
But what about the people that don’t have a chop saw yet lol
@@Exotiq. there is plastic guide 45 degree angle for that
@@ZuNunchaku oh ok cool well I guess if you have a 45 degree plastic angle guide then cool, but if you don’t have one then this is is useful too
@@Exotiq. what about if you dont have pencil or pen? Or you dont have paper? Oh wait, what about if you dont have saw 😂
That plastic box is cheaper than your saw, so what an excuse? You have welder there to weld 45 degree iron, bur you dont have mitter saw? At least you have 45 degree guide. This video is nonsense and you defending the nonsenesnes.
Welcome to the world 🤣
What cutoff wheel was that?
Dica maravilha
Otima dica de TRASAGEM do anGULO de 45°,SIMPLES E FÁCIL,OBRIGADO.UM ABRA"O.
lol u got no appreciation u got a weak brain
You aren't really cutting any corners doing it that way. Might even take a little longer.
'CUTTING CORNERS'...
... GET IT??
Unless you have the proper tools and are only cutting two. This is quite useful and faster if you're cutting plenty of pipes at right angle, since you have a template already. You dont even need the magnet.
Wonderful idea😊🎉
Wow I need to get rid of my miter saw and start doing this instead 🙃
Can you be certain your mitre saw will be available to you at all times?
If not, be grateful you now know how to survive without it.
@@trueaussie9230 oh shut up. can you be certain you'll have paper available??? or a marker??? see how that works? O.o
Чувак, всё это нарисовал, о потом на торцовке? Молодца! 😉😂😂😂
Or you could just cut the pipes at a 45 degree angle and save the paper scissors and marker for your kids art project
I think so...😂
I was thinking the same
And how do you propose cutting a precise 45 degree angle, without 'specialised tools'?!
Please, post a video to educate us.
@@trueaussie9230 You could literally accomplish this with a mitre gauge and a hand saw, both of which are not specialized. You can make a mitre gauge in half the time it takes to use this method to mark the pipe. This is overly complex for no reason other than getting views on TH-cam. Probably one of the dumbest methods I’ve ever seen to accomplish a 45 degree cut.
If one piece was cut at a 45* angle wouldn't the cut pieces fit together when turned ?
I guess you didn't have a 45° miter cutter.
Yes😄
it's good tutorial especially if you only have a hacksaw... actually it's good enough guide how to do it.
45 degree/ 45 degree makes 90 degree. This technique was overkill
Nice work, but no need for paper, and all this time, just calculate the width of the pipe and start cutting the pipe to the other edge at angle 45, you'll get the same result.
Your magnet already has the necessary 45ﾟ angle obviously.. If you attach your tube and let it overhang overhang the edge of the table you can simply use the table edge to scribe your line without having to do any of the paper and marking Tricks
sangat bermanfaat...
terima kasih sudah berbagi...
That seems way harder than just cutting a 45° angle in it and rotating it around 🤣🤣🤣
very good tecnik greetings from Indonesia
Thank you sir 😊
I'm Indonesian too😄
Safe to say: if you can’t eyeball a 45, then you ain’t gonna be able to figure out this origami project of yourn
Good job and thanks for the idea
Thank you my friend❤️❤️❤️