My Rears came with out the 3M adhesive tape and the contact sheet did not have a cutout to follow. I didn't notice until I had already installed the fronts so I struggled thru it vs. returning.
Impossible to remove the paint protection from the sheet its on without almost destroying it. A 2 year old must have put on the double sticking tape. Two were balled on mine and one folded up on itself. A bitch to get off. Glad I had some extra in my garage. Spring clips are WAY WAY WAY WAY WAY WAY to small with the factory flares. Did not use any of them even after I widened them as the instructions said you MAY need to do. Just add a 3rd screw for each one if you have flares and keep the clips... Husky will save money. The instructions said you need a drill motor and 1/8" bit....no mention here. On the good side they fit well and blend in on the front with the Ford factory steps.
This video is misleading. It is not at all that easy to install. The instructions that come with the mudguards are also different from the video. The ones i got had a print error so there was no drawing. Worst however is the clips. There is NO WAY they fit over both the mudguard and fender flare without prying them open. You husky guys need to find some better clips!
Agreed, they are kidding themselves if these clips fit with the oem fender flare, there is a reason they didn't show a close up of those being installed. With the boiler plate reply on both comments, it's fairly obvious they aren't listening. Similar issues with their fender liners I purchased too. I think they should stick to floor mats...
Buyers beware! Bought these for a XLT 2020 f150... as others have commented the clips are near impossible to get on over the stock fenders. They also damage the paint just as bad as if you drilled! Once installed the clips don't look sturdy enough to enough to handle snow or a lot of mud. I returned them shortly after.... horrible mounting design.
The instructions in the box are worthless. These are not much better. Installing the spring clips is a huge PITA because they aren’t long enough to easily install.
My Rears came with out the 3M adhesive tape and the contact sheet did not have a cutout to follow. I didn't notice until I had already installed the fronts so I struggled thru it vs. returning.
My front passenger side one fell off. Gone forever. Good purchase. Probably should have had AT LEAST one screw in them...
SHAME ON HUSKY!!!
Impossible to remove the paint protection from the sheet its on without almost destroying it. A 2 year old must have put on the double sticking tape. Two were balled on mine and one folded up on itself. A bitch to get off. Glad I had some extra in my garage. Spring clips are WAY WAY WAY WAY WAY WAY to small with the factory flares. Did not use any of them even after I widened them as the instructions said you MAY need to do. Just add a 3rd screw for each one if you have flares and keep the clips... Husky will save money. The instructions said you need a drill motor and 1/8" bit....no mention here.
On the good side they fit well and blend in on the front with the Ford factory steps.
This video is misleading. It is not at all that easy to install. The instructions that come with the mudguards are also different from the video. The ones i got had a print error so there was no drawing. Worst however is the clips. There is NO WAY they fit over both the mudguard and fender flare without prying them open. You husky guys need to find some better clips!
Agreed, they are kidding themselves if these clips fit with the oem fender flare, there is a reason they didn't show a close up of those being installed. With the boiler plate reply on both comments, it's fairly obvious they aren't listening. Similar issues with their fender liners I purchased too. I think they should stick to floor mats...
Wish I had read this before purchasing
HUSKY MISSED THE BOAT ON THIS ONE - TERRIBLE TO INSTALL!!!!!!!!!!
Buyers beware! Bought these for a XLT 2020 f150... as others have commented the clips are near impossible to get on over the stock fenders. They also damage the paint just as bad as if you drilled! Once installed the clips don't look sturdy enough to enough to handle snow or a lot of mud. I returned them shortly after.... horrible mounting design.
The instructions in the box are worthless. These are not much better. Installing the spring clips is a huge PITA because they aren’t long enough to easily install.
SPRING CLIPS ARE TOTALLY USELESS - NEARLY IMPOSSIBLE TO INSTALL - AND ONCE INSTALLED "DO-NOT" HOLD WELL :((
One more thing, HUSKY sent me a SOLID CONTACT SHEET - WHY!!!!! Am I to decide how to cutout?? NOT LIKING HUSKY!!!!!
dj p the same thing happened to me....
Happened to me too on the rears. GRRRR!