HONDA CBR REPLACEMENT FUEL PUMP & DOES IT START MARK SAVAGE

CHANGING THE FUEL PUMP EASY DIY

[@ianalexander716]

I love the excitement, that’s how I am completing my bike

[@yikenscot]

That brillo pad thing is in fact a debris filter comes as standard helps stop larger debris blocking fine filter.

[@marksavage]

yea i now know but doesnt look right lol

[@vazza7504]

Great video again Mark, electrical components fully immersed in fuel will not explode due to the lack of oxygen, same as fuel level sender unit in a car fuel tank, bare variable resistor sending fuel level is bare with 12 volt connection, never the right ratio of fuel and air to cause an explosion. That set up reminds me of set up in rover 75 1.8 petrol tank when replacing the pump in one of those. Thanks for your time making this vid Mark, enjoy watching you fixing stuff. On another note my zzr1100 c1 has fuel level sender unit inside tank, again a bare unit with 12 volts going to it and no explosions :-) the fuel pump lives outside underneath the carbs. Tip, if your two red fuel level warning lights on zzr1100 c1 it is probs your oil pressure sender unit not working, obvious if no oil light illuminates when you first turn the key to on. £22.00 to replace, single wire to unit on sump, not much oil weaps out no need to drain oil just undo and replace, to check it works before you replace it just unbolt cable and hold it to engine/earth with ignition on and a helper viewing the dash the oil pressure switch will come on and the 2 red fuel warning lights will flash on and off. The relay making a clicking noise is located in the tail unit. :-)

[@marksavage]

To me as you see it just didnt seem right but it is lol
Thanks for watching bud
Finished one out next week once the panels get here lol
Take care bud

[@StuntbikeOzy]

So you just cut the wires of the oem plug and connected them to the new provided plug right ? And just taped them up ? Looking to do the same.

[@bbriankb1086]

The "steel wool" in the bottom of the tank around the filter, might be to minimize fuel sloshing when the tank is almost dry?

[@stevewoodw]

Great to see you working on a bike again - not those silly car things....!

[@marksavage]

Theres a few on this cbr and the finished project soon
Thanks for watching bud

[@grahamsmith8122]

That might be the way forward on the RC45 im stuck with?

[@st8kout961]

6:22 I just finished replacing the fuel pump in my BMW sedan and I too was questioning plugging in the two wires to the fuel pump INSIDE the gas tank, immersed in gas. Turns out, gas does NOT conduct electricity. Of course, if you create a spark next to the gas tank where the fumes can ignite, then it's goodbye mark.
Now I need to replace the pump on my Honda, and from what I've seen, the BMW is MUCH easier and faster, maybe 20 minutes if you're slow.

[@ivangreat133]

The steel wool is a fuel return filter and should be put back on. Comments on your last video sadi this too.

[@marksavage]

Yes bud I made this after that video and before being told what it was , so I'm not stupid lol

[@jacob-no4tf]

Hi mark. that stainless steel wool is to trap air bubbles from drawning into the pump. the air bubbles produced by the pump return hose cause of cavitation.

[@marksavage]

Some had said this but still odd to find it in the tank lol

[@Noel127]

safer connection for wiring submerged in gas are self sealing solder that use heat to melt and seal the solder with insulating glue.

[@grahamsmith8122]

All the intank pumps come with the scouring pad, not sure why?

[@marksavage]

odd but yea bud , me neither

[@sekou3758]

For the gasket at 6:11, do you need to apply anything to the pump assembly before putting it on? On you just put it on normally

[@redleadervfr-v4906]

Well done Mare she sounds real good mate. Look forward to the next video buddy.

[@marksavage]

Out next week bud , should be a good turn out

[@dord1954]

Sounds great well done, I like the retakes that you shoot and then leave the original in too 😀😀

[@marksavage]

Lol , just like to show that I don't get it right
It did run well and still has now all serviced
Thanks for watching bud and next week the finished project

[@hoomannili]

That washing scrub is for suppressing vibration/noise.

[@andrewonmyway8184]

Well done Mark. Another plan sorted. Look forward to your next installment.

[@marksavage]

Just waiting for the panels and the last video will be uploaded
It should look amazing bud
Thanks for watching

[@gradysantiago8533]

I dont mean to be so offtopic but does any of you know of a way to get back into an instagram account..?
I was dumb lost my account password. I would love any tricks you can offer me

[@salvadorbeau4415]

@Grady Santiago instablaster ;)

[@gradysantiago8533]

@Salvador Beau thanks for your reply. I found the site thru google and Im in the hacking process atm.
Looks like it's gonna take a while so I will reply here later when my account password hopefully is recovered.

[@gradysantiago8533]

@Salvador Beau It did the trick and I actually got access to my account again. I am so happy!
Thank you so much you saved my account :D

[@adamcr_0691]

Could you tell me the manufacture that sold you your pump?

[@mark_mackaravitz]

Hello mark, I have a leaking fuel valve running off the gas tank on my
cbr 600f4, I don’t understand why because when I fill up it leaks and then continues to leak until I’m at a half tank of gas. Could you help me?

[@marksavage]

Patrol tank off bud as it sounds like either it's rusted and corroded half way , or could be rusted or damaged breather pipe
Guessing but get it off and view bud

[@MrDachampAli]

Where is the relay for the fuel pump? My fuel pump works with direct power from a jump

[@MsMicheal12345]

great video there mark ,crazy having wires in the petrol tank cannot get my head round it .

[@marksavage]

Mate tell me about it pmsl ,

[@JaysScript]

Mine is a 2006 and doesn't run off the vacuum system aka the air pump. I use a manual fuel tap. I have done everything and it's not starting. Any tipss

[@marksavage]

it can be a few things but would have thought you would need to have the vacuum system running as with carbs

[@tomnwoo]

Mark, as the comments in the last video stated, the "Kitchen Scrubber" is a pre filter to extend the life of the filter on the pump, Honda put it there, unless you are better at fuel system design than honda, read the manual and put it back

[@tomnwoo]

www.cmsnl.com/honda-cbr600f-hurricane-2006-6-england_model7999/filter-fuel-retur_16714mbg000/#.X0pmndNKiBQ. Thats the original Honda part

[@d.b.1419]

Great watch enjoyed it very much. Keep it up 👍

[@marksavage]

Thanks bud

[@TranceElbow]

Hi Mark - I had 1999 CBR600-FX, which was one of the last carb models and had a fuel pump failure. That one was mounted on the frame outside the tank and was held on with 2 bolts made of cheese. It took longer to drill those one than replace the pump. My local Honda dealer wanted £149 for a new one, so I got a used one on eBay for £15. Sorted.
I hope I never have the same problem with my CBF1000-A8 as it too is in the tank. Although you have given me the confidence to try it myself. Out of interest, how did you find that copy pump?

[@marksavage]

Good as gold , run it for a bit now and it runs fine and starts and primes every time
I do these videos to give people like you a little bit of help so you can do it
Thanks for watching bud next video
All finished and worth a watch

[@kx250braap]

That steel wool is supposed to be in the tank it's for the fuel return I guess I opened mine up today because my fuel pump quit working and was in shock when I seen that but after some research aka google forum search it belongs there I was in shock thinking that was my issue but it wasn't unfortunately now I need to buy a new pump

[@marksavage]

Yea but just seems odd being in there lol

[@stuart6420]

Good vid Mark. Keep the entertainment coming :)

[@4x4quadbike]

Well done .... love it when a plan comes together... 😁

[@marksavage]

Yes bud its all good

[@moreclips805]

May i ask what symptoms you were experiencing prior to the replacement? You mention you had power to the sender unit, was it just not priming? My bike primes and starts, but bogs under acceleration

[@marksavage]

i don't know what it was doing before as it hadn't been on the road for a long time, but i look at carb first
you are using E5 and not E10 !

[@LesroyBuckley]

Mate - ace video, ive just stripped mine down and it has the exact same metal scouring pad wrapped over the fuel filter. Must be a Honda factory ting?

[@marksavage]

So many have said but I left it off

[@LesroyBuckley]

@marksavage well mate, I cannot thank you enough for your excellent video 👍🏼 did you replace the fuel filter too just out of interest

[@marksavage]

@@LesroyBuckley I did bud as it had old fuel in it for many years

[@dominikkorycar5003]

HI Mark
Those strange looking wires you found in tank is fuel return filter. Its a original part and you will need to put it back in fuel tank.
Take a look on schematics on this website:
www.motorcyclespareparts.eu/en/honda-parts/2006-cbr600f-motorcycles/f-14-fuel-tank
Or try to google "16714MBG000, FILTER, FUEL RETURN, Honda"
Regards
Dom

[@marksavage]

Really looks odd but have been told this last week but I made this video after
Still odd to find it in there !!!

[@h22eh6]

Did the return line filter go back?

[@tallboy2234]

Great job, Mark!👌😁

[@marksavage]

Thanks bud

[@AJC762]

Mark, my Piaggio nrg mc3 front forks are rock solid. What can I do?

[@marksavage]

Change bud they are knackered

[@flatfour7506]

Thank you, all of us with EFI worry when this will happen. Rebuild or new? If anybody is gonna screw up our bikes it might as well be us. You did good, but why do you have to be So Funny?

[@hyp3_d138]

This is officially my the tutorial im using on my 954 lol

[@hyp3_d138]

@mark savage is it still running good with out the pre filter

[@marksavage]

@@hyp3_d138 perfect and runs very well, it's not in all on them and I hadn't seen one in any other motorbikes I've worked on and that's a lot of them
Found out that they did use them but with today's fuel etc a good filter works much better anyway

[@adrianscott614]

How did it run without the random piece installed?

[@marksavage]

As in the other videos on here bud much better

[@calumtroy3511]

Hi Mark bit irrelevant to your video but I just bought a suzuki gn125 having a new head a piston put on it today... How should I run it in properly?? Any advice be much appreciated

[@marksavage]

Ride it just a little slower through the gears and not full for the first tank full
You do need to get up to speed but then slow down to 50 again.
It settles the piston in better then next tank full open up to top speed just not giving to too much
That should be fine for the next full tank to ride as before
Keep an eye on the oil

[@calumtroy3511]

@@marksavage OK mate thanks so much for your time once again many thanks

[@calumtroy3511]

@@marksavage and how long should I ride it for each time I take it out for a run? Sorry for asking so much just had a headache to get it sorted wouldn't like it conking out again lol many thanks

[@marksavage]

@@calumtroy3511 starting and letting it run fir a good 10 mins then a shirt ride and home to check all the nuts and bolts
Let it cool for an hour
Start back up and a longer ride ,check over and ride like normal

[@calumtroy3511]

@@marksavage OK mate thanks I took it out yesterday for 10 mins and again just now for 15 sounds and feels good ill keep revs low for first tank of fuel should be fine thanks mate appreciate all the help and videos are wicked take care speak soon

[@bigeazy1591]

Why was your bike whining

[@marksavage]

first start in 9 years , camera mick, shed displacement of the sounds but it does sound like that and runs very well

[@tyronelee6235]

I have a peugeot speedfight 2 100cc engine that, i have totally rebuilt, new crank, piston rings bearings.... Do you want it?

[@marksavage]

Comes down to money and where you are bud to essex

[@tyronelee6235]

@@marksavage you can have it

[@tyronelee6235]

I'm in Essex all the time my family are in Southend and Romford

[@overthetopbiking523]

Mark I’m looking for a 50cc moped were can I buy one

[@marksavage]

Facebook sale , ebay or dealer bud
Just watch my videos for help

[@anthonyscott7806]

Hi mark ive got a lexmoto xtrs and i have no spark but power too the ht cap the whole bike has power however its not reading neautral would this contribute

[@marksavage]

This will be the problem, it has to read neutral to start bud

[@anthonyscott7806]

mark savage thanks for your help i just sorted the neutral situation out and my battery is dead so still got too wait so gutted about this good work on the videos me and my fiancè really enjoy them.
She has a lexmoto arrow and she has the same issue however she has a neutral reading and a brand new coil pack

[@anthonyscott7806]

mark savage okay so battery charged still no spark any suggestions

[@marksavage]

@@anthonyscott7806 so you have power
Out of gear , green light on
Side stand up
Engine kill switch on
It turns over
Did it work OK before
How did it run
What changed
What did you do ??

[@anthonyscott7806]

mark savage yes it has power and is out of gear green light is on and there is no side stand switch or connector for one
The bike did not run before i got it infact it disnt even have a plug for that matter
Killswitch is set too on position
I replaced missing parts like reg rek and spark plug cleaned carb and re assembled following your videos i have wired electrics up properly as the bike didnt even turn over when i bought it and i have tested coil pack with multimeter along with my new spark plug i have tons of compression power too the ht cap but no spark the cdi unit is fine because im fairly sure that it wouldnt turn over otherwise ive traced all wires and made sure theres no breaks in loom
I really aprecite your time thanks a lot for this

[@gabrielgalaxygh]

Did this now it starts but Boggs out when you give it throttle. I have a vid on my page if anyone thinks they can help me. Thanks

[@marksavage]

Did it do it before you did work on it ??
What did you do to it bud
Does look clean bike bud

[@gabrielgalaxygh]

@@marksavage it didnt even start before the fuel pump.
So far it has a new quantum fuel pump and filter, spark plugs, oil change

[@gabrielgalaxygh]

@@marksavage thank you for responding

[@marksavage]

@@gabrielgalaxygh
Tank off and go back over all of it making sure its all as it should be
Make sure the pump is in and on ok
Fuel lines ok and all air pipes and connectors back on as there's a few that can pop off
Plugs in ok and coil packs on
Theres the common rail too and all washers in and tight bud

[@gabrielgalaxygh]

@@marksavage I'll try it out and double check everything. Thanks again

[@Runitbackgabe]

Dude be my unc

[@ferreiraaveiro3908]

Wife caught you dancing? Lol

[@marksavage]

PMSL OH YES!!

[@ferreiraaveiro3908]

@@marksavage lol we cant live without them

[@TheDervMan]

I nearly stopped watching when you said "There might be anymore Mark Savage" :-o

[@marksavage]

Well I'm still here as it didn't go bang pmsl , panels coming tomorrow so Friday you'll get to see if I've done a good job of it .
Take care Steve

[@SSRooster]

Lol.... scrubber 😂😂 not pre-filter...

[@marksavage]

I've had both sides telling it is and it's not !
I took it out