NEW Bearing Separator MAC TOOLS
ฝัง
- เผยแพร่เมื่อ 16 พ.ค. 2023
- Join this channel to get access to perks:
/ @fluffymexicanik
MILWAUKEE RIGHT ANGLE IMPACT:
amzn.to/3DOtTxc
PUSH PIN PLIERS:
amzn.to/3XhaUSs
INGERSOLL RAND 1/2 AND 3/8 BUNDLE
amzn.to/3RJh39e
MOUNTAIN WRENCHES:
amzn.to/3U587uC
COIL SPRING COMPRESSOR:
amzn.to/3fhBMSx
SMALL TORQUE WRENCH
amzn.to/3SOe2D6
CONTROL ARM HOOK
amzn.to/3DbP3Ec
DIE GRINDER
amzn.to/3thpPj2
MILWAUKEE STUBBY IMPACT
amzn.to/3zVqAC3
DISCLAIMER: I AM AFFILIATE IN A PROGRAM WITH AMAZON TO HELP DRIVE SELLS IN THE PRODUCTS I USE, AND I DO GET A SMALL PERCENTAGE OF THE SALES WHEN MY LINK IS CLICK ON AND COMPLETE PURCHSE IS PERFORMED. IF I DO NOT TRUST OR LIKE AN ITEM I WOULD NOT RECOMMEND IT!! THANK YOU
-FMFAM - ยานยนต์และพาหนะ
Those separators are a life saver, but when you use it, use those flat pieces of metal and turn the separator side ways to support the silver parts don't use the bolts like you did because those bolts will bend then you wont be able to open it for larger bearings and those bolts are expensive and I don't think MAC will warranty them.
Haha can you tell it was my 1st time using 1, makes total sense
Before I got my bearing separator I had to score the inner race with a cutoff wheel and split it with a chisel. The bearing splitter really sped up the process. The splitter got a lot of use as I used to rebuild SAAB 900 5 speeds. Worked great for removing the inner pinion shaft bearing.
The new compressor is pretty quiet for such a big unit.
Thats basically how we would do it...but im trying ro be more professional lol but in reality theres a little more to the reasoning lol
Damn homie needed a small screw driver tool truck comes on Wednesdays my guy
Who needed 1? Lol
Dam good video bro. That look like the same setup use on our small Jeeps. Imma show you the tool I use for the knuckle..lol..if I can find it. I think it was a manufacturer tool tho..But I got a knuckle here that was in the trash I will use for the video. Some mechanics just do the complete knuckle cause they lazy. Lol
Lmao im telling you my dude, you be a bad influence, just cause i seen the ease when u did that PT i was like ohhh yupp im game 😅🤣 and apparently i used it wrong lmao which im glad the comment on this video was more imformative than bashing cause it definately was my 1st time buying or even using 1 lol not afraid to admitt it
Ill be looking out for that video though 💪
@@FluffyMexicanik lmao
ill be picking me one up soon thanks
Lmao didnt mean to influence the bad decision my dude 😅🤣
@@FluffyMexicanik ain’t no thing I got a job coming so I can use it
You shouldn't be pressing on the new bearing inner race FM. Take the OLD bearing and sand down the outer edge all around, about 1/2 inch deep. Use the OLD bearing to press in the NEW bearing by the outside edge / diameter. By sanding down the edge, it won't stick in the knuckle bore at all.
Did i presson the inner??? Oops i grad what i could...didnt realise i hadd the old bearing next to me until after....butttt i cant hindet the old bearing....*whispers* it was warranty 🤫🤫 dont tell nobody 😅🤣
@@Howtoautorepair Good physics application 😁👍 Bravo
@@FluffyMexicanik 😶
@Porch munkey absolutely. Old cars from 80's had 2 snap rings in knuckle. You could pull OR push the bearing in or out... Too easy a design. Had to make it a challenge 😡
Real mechanic sh1t right here! Gotta do what you gotta do sometime to make it work, I’d definitely say this is a great example on how Harbor Freight is a useful store to have around.
That compressor is a bad sumbich Fluff, twin recips on what? a 350 gallon tank? I'll post one of the new Screw Compressor I just installed here. 25hp, 100 cfm with an oversize refrigerated dryer. Bearing separators are a must around here, I bet Mac got a big markup on that one though.
I think its 250 shit frosty im not sure lol our previous was 150gal and this 1 engulfs it 😅🤣
In reality they should have a hydraulic press that you dont have to hand pump, than less time comsuming
True but having a feel for it i feel is important
@@FluffyMexicanik yes you are also correct
that tool needs to be turned sideways, to how you did it, so the bolts arent taking the force.
Yea somebody else mentioned that.. and makes total sense...it was literally my 1st time using 1 and thats how id seen it done so maybe thats why i was so unsure about the tool all along lol