Blades - Things I Wish I Knew Before??? | Must Know Info About Blades & Blade Sharpening
ฝัง
- เผยแพร่เมื่อ 3 มิ.ย. 2024
- Everything practical that you need to know about how to choose the best saw blade for you and how to get the most out of your saw blades. I also share the state of the art sharpening service that I have used for years to get my saw blades sharpened.
W.D. Quinn Blade Sharpening Service - quinnsaw.com/carbide-tipped-s...
My favorite Blades:
Favorite Miter Saw Blade - geni.us/YkCGKv on Amazon (commissions earned) (Sub-Micron Grade Extended Life Carbide and 6 degree hook) I USE THE SM6300 personally NOTE THE LM6300 is not as high quality carbide and his a more negative hook angle.
Favorite Table Saw Blade - geni.us/X3f128 on Amazon (commissions earned)
Blade Cleaning Solution - geni.us/RUUHWe on Amazon (commissions earned)
Blade Cleaning Brushes - geni.us/1rV93M on Amazon (commissions earned)
Blade Cleaning Plastic Container - geni.us/Wjumz68 on Amazon (commissions earned)
Rockler Blade Cleaning Container - www.rockler.com/router-bit-an...
(0:00) Common Mistakes with Blades
(1:04) WHERE TO GET BLADES SHARPENED
(1:41) WHAT ARE THROW AWAY BLADES
(2:38) HOW MUCH SHOULD YOU SPEND ON A BLADE
(4:29) USE INDUSTRIAL BLADES FOR HIGH VOLUME CUTTING
(5:04) MY GO TO MITER SAW BLADE
(6:00) WHY USE INDUSTRIAL BLADES
(6:50) LOW VS MID VS HIGH QUALITY BLADES
(7:52) CUT QUANTITY & BLADE LIFE
(8:28) BLADES THAT MAKE SENSE TO ME
(9:07) QUINN SAW CO ENGRAVES YOUR BLADES
(9:34) HOW MANY BLADES SHOULD YOU OWN
(11:06) STANDARDIZE YOUR BLADES FOR SIMPLICITY
(11:28) MY GO TO TABLE SAW BLADE
(12:16) MY BIGGEST BLADE MISTAKES
(12:57) YOU MUST CLEAN YOUR BLADES FOR MAXIMUM LIFE
(14:10) HOW TO CLEAN YOUR BLADES
(15:45) HOW TO TELL WHEN A BLADE IS DULL
(16:39) ALWAYS SAVE YOUR BLADE BOXES
(18:31) HOW TO SEND IN YOUR BLADES FOR SHARPENING
(19:09) HOW TO CLEAN YOUR OWN BLADES
(20:54) FINAL THOUGHTS
My Favorite Tools - Insider Carpentry Amazon Site - www.amazon.com/shop/insider_c...
Support more content like this by becoming a PATREON SUPPORTER - / insider_carpentry
INSTAGRAM - insider_carpentry - แนวปฏิบัติและการใช้ชีวิต
As a fellow carpenter I am shocked by the lack of likes on this video. This is the kind of valuable information that most of us probably don’t think about, but yet has a huge impact on money and time saved. Much appreciated.
All sounds like work to anyone under 45 yrs old. Why work when they are all going to be a rich TH-cam stars, or invent some POS and live like a Kardashian.
I don’t think most users know there are high end blades.
@@bret9741maybe. I think pros know pro tools and blades though. Home owners would probably think diablo is upper tier, so I agree on that front
When looking at the initial investment of buying a $50 blade vs a $100 blade you need to look at longevity of sharpness first. The Forrest/FS quality will outlast the Freud/Amana quality 2:1. It’s basically a wash in cost. However, when you get to sharpening you pay the same amount of money to sharpen cheap blades vs expensive ones. Every time you spend your $25 to sharpen the $100 blade you get a $100 blade. Sharpen it 5 times means you have spent $100+$125 = $225 to get $600 worth of blade which outlast the good quality 2:1. That’s without even talking about cut quality. Point being buy good blades they will last years of decent use.
We always buy them in pairs. One is on the saw the other is either at the sharpeners or is sharp on the shelf.
Well said!
Excellent blade tutorial. Thank you. Many years ago I adopted a European strategy that has enabled me to maximize flexible use of my tooling: I specified 30 mm bore when purchasing all my high quality blades. At the time, I ran a German combination machine with 30 mm arbor; others in my shop have 5/8", 3/4", and 1" arbors. By use of the appropriate saw bushing (I buy from Amana), I am able to deploy any blade on almost any machine, at times maximizing the usefulness of certain specialty blades (e.g. triple chip.) I also had custom 30 mm O.D. collars machined, one with 5/8" I.D. and another with 1" I.D., that allow me to deploy my 8" stack dado on either table saw, RAS, or shaper. I run mostly Leitz and Forrest blades, purchased in pairs. Care and maintenance such as you present in this video have allowed most to remain in service for decades. Besides regular cleaning, another key to optimizing cut quality (and minimizing power requirement!) is the use of blade stabilizers, especially on lightweight table saws. With stabilizer diameter equal to as much as 50% of blade diameter, the improvement in the performance of a thin kerf blade is dramatic.
This is one of the best videos I have seen. His presentation is flawless and his opinions are right on. Great job.
Most of the best answers are loaded with question. Thanks for your take on this topic.
Thank you so much for such a saw blade masterclass. I wish I could thumps up it 1000 times.
Very helpful Spencer. I didn't appreciate how important it was to keep blades clean. Thanks for the many tips and good advice I get from your channel. Mike (UK)
Dude, that was off the charts for TH-cam - Well done
Keeping your blades clean is a must. I just cleaned about half a dozen blades that had been relegated to the dull blade pile by others that have access to my table saw that came back to life after a good cleaning. I have been using the Freud blades for a bunch of years professionally and I have had 0 problems with them. I have them sharpened all of the time and they come back good as new. But then again I try and stay away from thin kerf blades especially on my hand held circular saws and even more so on my beam saw with it's 16 5/16" blade. As a matter of fact I have a whole stack that are ready to go to the sharpener right now. That's partly why I clicked on this video. Some of them where being tossed out on job sites and I grabbed them from the trash bin. They have never been sharpened before and I'll send them in and have a nice sharp blade for a third of the price when I get them back.
We've all been there - trying to outsmart ourselves and buying dirty cheap blades. Then you find a really good sharpening parlour and all of sudden end up with bunch of 200 Euro a piece blades. And it makes sense. Great video, as always. You've become a really good teacher.
Really helpful information! It shows how intentional and serious you take your business. It’s hard for some to sit back and perform maintenance but this shows it is necessary.
I have been sharpening my Dewalt blades with my Foley Sharpener for years. Always have excellent results.
Spencer,
Really enjoy your channel, your videos are well thought out and really show your knowledge base.
As an Engineer by trade I enjoy the way you make a process out of the job, the stop block video series really
demonstrates how you recognize efficiency for your company while increase your speed an accuracy on the job.
Look forward to more informational videos.
great info. never knew you should clen your blades. Love your videos. HVAC worker now but 13 yrs as a carpenter. Still do it just not on the daily. You always put out amazingly informative videos, thank you.
Excellent video! Best I"ve ever seen about saw blades on TH-cam!
Always great content. You are a reference in the field of finished carpentry.
Quinn and FS Tools just got 99,000 new customers when this video posted
I'm happy to send business to good companies that help us do our job better.
Much appreciated. You hit every question I’ve had. No more box store bargain blades.
Wow. That was interesting. The guy I worked for never have nice blades and we all just got used to cutting with them. The cleaning tip blew my mind as most of the time on my personal saws I changed blades because they had build up. Thanks for the tips
Hi Spencer - as I’ve watched more of you videos, I want to comment again.
I really like your take on means & methods - how you approach your work. Your balance of precision, efficiency and production repeatability is truly admirable. I recently came across your channel and have gladly subscribed.
In my younger days, after college, I apprenticed with frame and later trim carpenters for roughly five years. I later went to work in commercial cabinet shops, first in production and later as a project manager. From there I went back to architecture (what I studied in college). My orientation toward working with the tools is similar to yours, but my experience is less evolved.
As my architecture career developed, I moved around the country following commercial projects...and the tools went into storage. I’ve recently decided to settle in Eastern Indiana and gotten the tools out of storage. As I reconnect with my love for woodworking, I hope to synthesize my experience and develop a work style similar to yours.
Keep up the workmanship and the videos!
Man you just answered a bunch of questions I had, it's about like finish, it's a deep worm hole we get into...thanks for your time man .
One of the best channels on TH-cam.
f s blades are the best hands down. 27 years cabinet shop all i use. love your channel. you taughtme quite a few things
LOVE HOW DETAILED YOU ARE WITH YOUR DESCRIPTION AND LEAVE NOTHING TO QUESTION ! just stumbled across your channel. Recently retired from 35 yrs of emergency services work but started out carpentry work as a teenager and young man and I am looking to dabble again in my own house but am so pleased to find EXPERTS on you tube that are willing to share . After all these years it is evident that I have a lot of brushing and catching up to do BUT eager to start the journey with renewed enthusiasm and vigor & NOW MORE IMPORTANTLY ARMED WITH VALUABLE KNOWLEDGE to proceed with !!! thank you
I WATCHED YOUR SHIP LAP VIDEO and picked up some valuable tips !!!! because that is what I am using in my first project covering a beautiful natural stone fireplace and converting it to something more modern looking ( MAKES ME WANT TO VOMIT 🤮🤮🤢 ) having to paint the bottom stone white and cover the top with ship lap BUT as the saying goes HAPPY WIFE !!!!! LOL
You share sooo much through your experience and always improving and thinking about improvements ... and your channel has been a huge joy here on TH-cam. Cheers Spencer. Your excellence is inspiring
My pleasure 😊
You pretty much summed up everything I've been thinking about blade selection/ cleaning and sharpening. It's just nice to hear another professional come to the same conclusions! And, yes- the sharpening service is really only worth it when it's done by robots.
I bought 3 FS Tool saw blades from a place called industrial saw blades which was next door to where I was working. This was in 1990. I still have them today and use them regularly. The are excellent blades and I would recommend them to anyone looking for good quality Blades.
Great video! I’m a self employed carpenter and it’s funny when I worked for people before I never knew to clean blades. When I went on my own I realized my blades weren’t cutting well even though they where new and thought to clean it and it cut like new so I do like you said clean it quite often! In a pinch I use windex and a toothbrush on site.
Great knowledge and high quality work, thanks Lewis
Awesome info/recommendations! Thanks!
Love your content man. You really know what you’re talking about. I’ve learned so much from you, thank you!
My pleasure!
Great informational video. Keep them coming.
Thank you for the awesome information! Bookmarked the sharpening service for the next time. My local guy in NW Ohio does a good job, but it takes 6 weeks normally and costs much more!
Great way to end a Friday!
As an amateur, I have learned much from your videos. I am starting a new home build project and information from this video will be put to use. Your tip about blade cleaning will be also applied to the chain for my chainsaw. Similar issue with build-up on the cutting surfaces.
As always, you get what you pay for. Thanks Spencer..
a long time ago before track saws were invented ... I had to cut solid maple panels that were finished - face up with my Skil worm drive ... I asked the tool store manager IF they might have a saw blade that will give me the cleanest cut ? With out missing a beat , he showed me the TENRYU blades and he said , that YES they do cost more BUT they will give you the cleanest cut and they will last a long time before needing to be resharpened ! Well he didn't lie - every cut was perfect - no chips or splinters and no need to sand the cut smooth . Since that day I have only bought the blades that TENRYU makes . So unless your using a saw to do demo work - don;t waste your money on a cheap saw blade
Great information! Thanks Spencer!
So good! Great tips Spencer…thanks!!
Great tips to know I use 80t and 60t blades most of the time
Clean blades are a must. I also use the blade cleaning solvent. I wax my blades after I clean them. I have not had any more problems with pitch/glue build up with the added step of waxing. I wax the cutting platforms as we, like my table of the table saw. This content is extremely helpful and also accurate in explaining saw blade best practices. Great info.
Very informative video. Thanks Spencer.
i also user those fs tool blades because my local sharpener sells them, your the first person i've ever heard recommend them. A&H sharpens them close to 20 times, which i have sharpened bi weekly just because i've become so spoiled with sharp blades that i cant stand when they show any signs of dulling. glad i found your channel, you got a new subscriber
At first I was gonna say, you are NUTS paying $180 . For a blade. But after listening for the reason and use of it. I will be buying these blades too . Thanks much
Cool guy explaining cool details on cutting blades
Another great vid. Always learn something watching you.
Love the Tenryu Gold Medal blade and I've run a lot of blades. Super quiet and deadly sharp. I agree on sharpeners....none of this matters if you don't have a high quality knowledgeable sharpener.
Awesome knowledge you shared with us, greatly appreciate your efforts!
Matsushita was always blade of choice, cut better dull then most blades sharp, haven’t had good luck with reshaping, still have large inventory of pristine used blades, definitely going to try out your guys on one, high dollar blades make you cry if you hit a nail.
Thanks buddy
Just ordered both the 10"& 12" blades from your links...Happy to support this channel!...Keep the awesome content coming!
Much appreciated
As always, fantastic information Spencer. You've also triggered a ton of great comments from other experienced professionals. I'm not a professional, just a reasonably talented DIY'r. It's all good for a guy like me looking to up my game. I always look forward to your video drops, keep 'em coming!
Great video as always lots of good information
Great video, thanks Spencer!
Excellent video! Thank you.
Your videos are really first class. A gentleman and very professional tradesman. You are an example of what we should strive to be. An example for others who is knowledgeable and willing to teach. Thank you. Be well.
Thanks 👍
👍👍 I’ll definitely agree with cleaning and a high quality full kerf blade, do how ever do use separate blades for plywood, ... A high quality rip blade will often leave a glue ready cut. I was a part time cabinet maker, unfortunately my shop has been setting mostly unused for a few years due to illnesses.
Great tips brother. Thank you!
During my woodworking / carpentry career I chose to help (as an apprentice) an up and coming sharpening operation who had decades of experience, but was struggling to get his operation off the ground. It was one of the best choices I've made. We worked hard, in rough shop conditions, and ordered a lot of late night take out pizza. 20 + years later he passed his operation down to his son and they have expanded into a very successful operation. His gained knowledge was key to providing top quality services, and intelligent advice, to his customers which simply didn't understand anything beyond "dull and sharp". Having someone who knows the mechanics of cutting tools is huge.
Hamronale Carpentry
Thank you, this is a fantastic video with invaluable information.
GREAT content. Thanks
Great info, thanks.
Thanks Spencer. I was always sending my blades in to get sharpened to remove that *gunk* as I called it. It never occurred to me to research how to clean them myself. I used your link below to purchase the kit. Hope you got your commission. Andy
100K right around the corner.
Well done fella and Hi from Scotland
Awesome video! Thank you for the great content!
I learned that car door edge moulding fits the carbide teeth of a good industrial blade cut to fit for your blade diameter and put a piece of painters tape on the two edges where they meet and your carbide teeth are very well protected during shipping or storing them for future use
Very informative video. I really appreciate you sharing your lessons learned and expertise. Will definitely use your links for some of this gear. Thank you!!!
As a trim carpenter and cabinet maker for 30 years, kudos on this video. Years ago I bought a Forrest blade and have never bought another brand since. Their sharpening is amazing and they sharpen almost anything from saw blades, planer knives, router bits, lathe tools and jointer knives. As loyal, stubborn and old as I am, I might grab a FS blade.
Same, but I dare say, my experience has shown a professional sharpening is the key component. I think the heavier blades are better because of momentum more carbide. I really don’t think 90% of woodworkers could tell a difference in a cheap blade vs a quality blade after a professional sharpening.
Excellent video. Very informative. Thank you!
I’ve never thrown a blade away. I’ve always taken my low quality blades whether chipped or dull to get retoothed with high quality carbide to be sharpened. I’ve even had my blades teeth redesigned for optimal use on my table saw or miter saw so they cut smoother and faster. I’ve been using the same saw blades now for 20+ years. Cleaning for sure helps them last longer than you’d ever think too.
excellent. I've learnt quite a lot of important information. Thank you.
Great video, I also agree that you get what you pay for, I clean my blades with a table spoon of Spic and Span (one box will last a life time) with warm water, soak for about 15 minutes and clean with a brass brush, like new !
I think Freud and CMT get sold a little short. In our shop, we use mostly Forrest blades. However, there are several Freud blades in use, on miter saws and lighter duty tables saws. They perform quite well if used judiciously. Our philosophy is they get one sharpening, then out to pasture. Where the really good blades shine is in the mill. We have two big old Dewalt 14” radial arm saws, one for rough and one for fine. We also have an old Clement table saw with power feed for rough rips, and a big Tannewitz also with power feed, for all the fine rips. These four saws are in use eight hours a day, all year round. They have the highest quality blades we can get.
Thanks for your excellent content! You really spend the time to explain thoroughly. Your care and thoughtfulness is appreciated.
PS You mentioned Southern Yellow (Short Leaf) Pine. Years ago we ran a ton of that stuff for structural components. It’s the worst wood on tools I’ve ever had the displeasure to mill. But man is it robust!
I use Formax saw blade wax on my band saw, circular saw blades and bow saws for pruning green branches . Sometimes I'm sawing rough green wood I think it helps reduce pitch build-up.
Excellent video. Another good reason for keeping blades clean is to prevent blade warpage 05:51 due to resin/pitch causing excessive heat build-up along the periphery of the blade.
For sure, could not agree more, especially keeping blades clean. I decided awhile back to invest in a really decent sharpener, Hask Pro universalsharpener, to sharpen all my blades, 6 1/2" through 12" tablesaw and miter blades, plus being able to sharpen hole saws and router bits. Used a few sharpening compaines in my day and went through a few sharpening machines, but hopefully this will be my last one to purchase...
Excellent Equipment, a must needed at Home or Even for Working
Great content, as always!
good info. But one correction/disagreement. Freud blades are not the same as Diablo red blades (is they cheap big box store version). the Freud line blades are the higher quality industrial carbide blades which is what i use & they are great blades (years ago before they rebranded things they were synonymous, but now the Freud blades will usually say Freud Industrial and don't have the Red paint on them generally.). Not something you can buy at the big box stores.
Just bought a Freud for my SawStop 3.0. Waaaaayyyyyyyyyy better than I expected. $60 at Rockler.
I like The Tenryu as well. Makita eased to put them on their miter saws.
CMT has a high end blade that seems to work very well. Wisconsin Knife , forester of course.
Very informative, as always.
Thank you Spencer. I learned invaluably good information from you here... I am surprised I didn't think to clean my blades without being educated to do so, my attention to detail must be slacking. I clean everything else in my world pretty fastidiously. You've earned a new sub's. Carry on Sir!
Awesome job
thank you for your videos they are very helpful
Thank you for this info. I’ve been looking to upgrade from these thin Diablo blades. I just ordered the fs tool blade and I’m looking forward to deflection free cuts.
really enjoy your vids they are very helpful
Great info video. Thank you
Outstanding video! You just acquired a new follower. Thanks for the great info.
I am very happy with ridge carbide blades that stumpy nubs recommends.
I put a note on my blade storage box to remind me to send them to quinn when they need to be reshaped.
Nice video
I learned a lot, Thanks
Well, I finally dulled the stock blade that came with my new DW716XPS. I bought an FS Tools blade to go with it based on your recommendations when I bought it a couple months back. Threw it in last night so I could finish the walnut miters on my builtins and make the cuts for my mantle. Without a doubt, the smoothest, easiest, cleanest cuts I've ever made. It can't even be compared to the blades at the box stores, it's leaps and bounds ahead of them. It's going to be a joy to work with, should increase my efficiency, and my clients will get better results in shorter amounts of time. Thanks again for an awesome video and recommendation Spencer!
You bet. That blade spins so good on a 716. Probably my favorite cutting combo.
Great video as usual!
Great content in this video. Keep up the good work, sir.
CMT blade cleaner
& no mention of their blades, very informative video & thanks for your time
Great content. Keep it coming.
very informative video
Love these blades...well worth the investment
Excellent, excellent, excellent
Thank you!
Great review!
Appreciate the Great vid, I’ve always wanted better blades but unsure if I’m paying more for better quality...
Great video mate