Pro Tips for Fast Square BASEBOARD INSTALLATION - To Cope or Not To Cope???
ฝัง
- เผยแพร่เมื่อ 27 ก.ค. 2024
- In this video I give some work flow tips and advice for installing square base with production speed and accuracy.
Baseboard Tools Amazon Store List - www.amazon.com/shop/insider_c...
Leica DISTO D2 New 330ft Laser Distance Measure - geni.us/aHc6 (Amazon)
ProSensor 710 Precision Stud Finder - geni.us/dZSOACH (Amazon)
Occidental Leather 9525 M The Finisher Tool Belt Set - geni.us/EBkGr (Amazon)
ProKnee Knee Pads - geni.us/O5yL (Amazon)
2-Piece Stainless Steel Pry Bar Scraper Set - geni.us/lQqSO (Amazon)
My Favorite Tools - Insider Carpentry Amazon Site - www.amazon.com/shop/insider_c...
Intro (0:00)
Always Use a Headlamp (0:33)
Use Two Cutlists (0:50)
Toolbelt Setup for Baseboard (1:58)
How to Measure Accurately (3:35)
Number Ever Piece of Base & The Wall Where It Goes (7:49)
Splicing Runs Over 16' (9:04)
A Must Have Flat Bar (10:14)
The Best Knee Pads Ever (11:37)
Nailing Off Base Production Style (12:13)
Should You Cope Flat Base? (17:51)
The Value Mindset of Quality Production Trim Work (17:51)
Support more content like this by becoming a PATREON SUPPORTER - / insider_carpentry
INSTAGRAM - insider_carpentry - แนวปฏิบัติและการใช้ชีวิต
THANKS FOR SUPPORTING THIS CHANNEL BY VISITING THESE AMAZON AFFILIATE TOOL LINKS!!!
Baseboard Tools Amazon Store List - www.amazon.com/shop/insider_carpentry?listId=2SDL8QSJPKV7A
- Leica DISTO D2 New 330ft Laser Distance Measure - geni.us/aHc6 (Amazon)
- ProSensor 710 Precision Stud Finder - geni.us/dZSOACH (Amazon)
- Occidental Leather 9525 M The Finisher Tool Belt Set - geni.us/EBkGr (Amazon)
- ProKnee Knee Pads - geni.us/O5yL (Amazon)
- 2-Piece Stainless Steel Pry Bar Scraper Set - geni.us/lQqSO (Amazon)
- Support more content like this by becoming a PATREON SUPPORTER - www.patreon.com/insider_carpentry
Seasoned finish carpenter here. Really enjoy your videos!
I am a well seasoned finish carpenter. Although I've installed thousands of miles of base over the years. I really enjoy watching this video, and your others this channel. I think you're somewhat the Bob Ross of carpentry for me. You have a fantastic attitude and you are really enjoyable to listen to. You also are a very good instructor. The new wave of carpenters coming up now are lucky to have this resource, and would benefit greatly from watching your channel. I've been at this a long time, and I'm not ashamed to say that I've learned some valuable bits from your channel. I've always liked learning new processes and techniques, as well as, seeing that the some of the ones I employ still hold up. Lastly, with the stresses that Covid has brought and the insane work load I have these days. I've been grudgingly going to the next home to start the next project. Somehow you've inspired me to tool up with a fresh and positive attitude again. And for that I thank you.
Thanks for taking the time to comment. 👊👍 You’ve mutually motivated me to keep making content like this. 👍
Your comment has me subscribed. I'll check out more videos from this guy.
You know you've done alot when you describe it in miles instead of feet💪
If you can install thirty five sticks of baseboards per day, forty hour week. It would take forty one years to go a thousand miles
@@randywilder2797 he doesn't know how much base he has installed so he just says miles. It's some way of pretending your elite in your craft.
This is by far the best baseboard tutorial on the internet. Would love to see more of these "workflow" style videos
This was the most complete explanation, on how to install baseboard from a professional point of view, that I have found on the internet. Thank you for sharing your Wisdom and Experience with us...
I think the only thing he could add to it would be scribing base to fit a existing floor.
I had to do that recently on hardwood floor transition.
Every one of your videos that I've clicked on I've though "I do this stuff daily for years now. What could he possibly teach me about installing base, or installing doors, or whatever" and then you start dropping tips to solve problems that I usually don't put too much thought into. Your attention to detail makes me ashamed that I ever say "good enough" just found your channel today and instantly one of my top 5 favorite channels. Keep it up man and thanks for sharing the wisdom!
I've been a carpenter (broad-spectrum) my whole life and at 56 I still like to learn something new, even from someone much younger. I'm not a trim carpenter by trade but we all do it at some point. Already I have picked up many new tricks. I enjoy watching people who know their trade and do it well, it is how I learned most of what I know. Watch, comprehend, repeat, perfect. Enjoying your videos!
as a drywall guy if I came into a new build and someone already marked my studs and pipes I would find that guy and buy them a nice meal or case of beer
For real. Hahah coming from a drywall guy hahahaha
On jobs I manage, I'll use a piece of 1/4" plywood with a cutout of 1 1/2" wide by 2" deep and attach to a stick roughly 3 feet long. A can of spray paint and setting the cutout next to each stud makes short work of marking each stud on a job. It saves time for every trade from framing on and in my opinion, is time well spent to do.
@@personalfavoriteshill7547 It's nice when the tradesmen respect each other! As a painting contractor, I hate when a carpenter shoots so many nails into the trimwork that you swear he came off the battlefield and was shooting a machine gun!
Exactly! U could be in a ruff mood and come in to a marked it house! Makes the day a bit better!
@@pointedspider YOU need to learn how to spell.
Pro knees are a godsend to floor covering installers ! No more strap pain , rotating and slipping down ! I forgot mine on a job and had to use the foam and hardcap type ! It brought back painful memories ! Nice tips for people who WANT to improve in their trade !
I've never heard the value principal so superbly articulated. Great job! Awesome video.
Another great video. Knowing when to produce perfection is key . Especially as a subcontractor.
I love your work flow. I’m an old school carpenter and always find something in your videos to step up my game. Thanks for the tips
Thanks for sharing man it’s refreshing to see someone talking about the real parts of the job instead of fluffing it up to look more extravagant than necessary
While I only work on my own home, I do see a lot of efficiencies built into your workflow. I used to make signs. I had to bust out a lot of signs in a short timeframe. Economy of motion and organization while still providing a high-quality product is the name of the game. I, too, watch every second.
This is absolutely one of the most comprehensive videos for base-boards. Excellent work, excellent video.
My wife and I recently (April 2019) bought our first home. We got into a bit of a loggerheads over whether or not to cope the baseboards (entire house is being remodeled). Simple 5-1/4" with and 1/8" roundover. I won't say who's side is supported by your experience, but I will thank you for making it clear and giving us confidence to move forward!
Reallly appreciate how you share your experience and what you have learned through out your career. You do a superb job explaining how you have grown as a carpenter and what works
Some great tips, especially about the return pieces behind doors. I totally agree about the Franklin Finder; it's the best.
As a retired finish carpenter your tips are very beneficial and time saving. The kneepads should be required. I'm having knee surgery in 2020 because I neglected pads.
Keep up the professionalism. You are a true craftsman in the old style.
I haven't seen true craftsman like this since the 80s. Yes I also should have used knee pads.
I have yet to have an electronic stud finder last more than a month or two for over a decade. I gave up and went back to stud buddy magnets. I take care of my tools too. One day, they just don't work anymore. Very expensive drawer full of stud finders. Good job as always!
You may actually the best on TH-cam. Nice job. I’ve not see anyone be so concise and so complete. I learned something every sentence. Really nice work that I appreciate. I’m not a tradesman, but I’m doing my own home, making my own woodwork and installing it along with the built-ins. I have what I considered adequate tools to do my work. I was wrong. I will likely be purchasing several of the tools you have in your bag. Again- thx for this video. All the best to you.
Thanks man. 👍👊
Really enjoy your channel and I always learn something new. I also appreciate your down-to-earth attitude and the reasoning behind the choices you make. It makes me respect the expertise that goes into this line of work all the more.
I am planning renovations on parts of my home. Your "value" tips are especially helpful to assure I can stretch use of my dollars as far as far as possible and definitely details to keep in mind. Thanks for posting.
Not much to say but well said! It's satisfying to see another carpenter's workflow to confirm your own workflow
This is why I love what I do. As a remodler. Usually I attach drywall and the bottom screw marks the stud and is never filled with mud. Gives a real spot and we can get the stud really easy. Where I'm at floors and paint are completed usually before you can trim.
Excellent video with invaluable insight. I really appreciate how you explained that coping in this instance wouldn’t benefit the customer. This is a philosophy I learned years ago and it has helped me in so many ways. So many decisions over the years on what to do where the deciding factor was “Does this benefit the customer?” that ended with success. You are a true professional. Thank you for sharing your knowledge
It's nice to find a skilled young craftsman, other carpenters (slow, marginal carpenters) are always telling
Me " you can't do that ", it's all about speed and end results, I will say in my area pre painted white millwork called "complete"is prevalent, adds another level of techniques, I haven't used orthodox techniques in years and still trying to be more efficient every day, folks on TH-cam are lucky you give out your tricks, you the man. (Been at it since high school class of 80).
Pete
Great video bud! A lot of good tips! One little thing I do is I always add a little line next to my number 9, that way 9 and 6 never get mixed up because something got flipped. You truly are a master at your craft! Keep the great content coming!
Thanks for the video. Perfect timing as I’m just about to start trimming out our new house and was looking for some tips on how to be the most efficient with the use of time and material.
Great Video! Also nice to hear someone being practical and honest about quality vs. value. That stud finder looks great. It's going on the Xmas wish list for sure.
Labor-to-value discussion was gold. Excellent work. Thanks for sharing.
I really like how you phrased that about if what you're doing isn't adding value, good way to think about it
I like when I get to the end of a long video and realize I didn't skip one second. Nicely done!
That makes me happy. 👍
This is pure gold for the ears. After watching this video I bought some of the tools you recommended, most from your link, and what a difference in the process time, quality and level of enjoyment. Thank you for putting this content out🙏🏾
I appreciate the support. 👊 Glad the content is helpful. 👍
Id love to see your process with stain-grade trims. Great info as always. Thanks man.
Your pitch for knee pads is spot on. I’m 64, did not wear pads. Now I limp, can’t kneel, don’t sleep well becuz of bad knees.
Having replacement knee surgery this year😢.
Those little details about where to put the nails as far is one on the top and one of the bottom it said a lot about you thinking on the guy that comes after you to fill those holes and prep for painting , less filling holes and being more productive, thanks! I really enjoyed your videos!
"Value engineer the job" comments are spot on. Very impressive video.
I don’t think you realize how much that quote changed my outlook on approaching a job,
Thank you for the professional point of view. Well done.
I subbed I work with a general contractor learning his every move and thought lol. Thanks for taking the time to edit all this and put it up we do a lot of finish carpentry but really anything at all we don't mind. I loved your stave shim video that's going to helpe me so much with stain grade!
May God richly bless you and your family
I cut the longest pieces first, leaving any outside miters rough to be marked directly, & standing up the off-cuts so it's easy to select lengths for little waste. Then cut & install the furthest & most visible pieces in each room wall to wall. I take all measurements wall to wall, noting "-TK", ">", or "L" on the cut list for needed cuts.
Pre-sanding will make the finish come out better, & a micro bevel on the bottom edge helps the painter keep paint off the finish floor.
You are the best channel for your trade on TH-cam! Your channel is going to make me better at what I do. Thank you for that!👍👍
Watch @ finish carpentry tv on you tube that guy is the best. I'm sure you'll enjoy his knowledge. His workmanship is next level. Enjoy, tell him tony hernandez recommended
Love this channel! More videos please!!! It has helped me as a new contractor so much I love it.
I'm not a carpenter, I don't do carpentry, I have no interest in carpentry but I ended up watching this whole video and found it fascinating. Great job!!!
I'm feeling real smart this morning! I run my own Handyman biz and do lots of baseboard work but it's usually not an entire room, so I learned a few things from you so Thanks! I feel smart because other than those knee pads I use the EXACT same tools that you use across the board and for the same reasons you mention. We could literally trade tool belts with no differences. Love my pants with built-in knee pads vs those beasts you use but I'm going to check them out anyway!
You sold me on that stud finder. I have never been able to move fast with mine. You cruise right along. 👍 I'll use your link.
Dude,,, you Sir are a Beast.
You are specific, and to the point. It’s like your gift is in acting. Every word is carefully crafted to minimize waste of motion too.
Value upon value and l just found your channel today. Appreciate your videos ✍🏼.
I am glad that you made the point of how it is done in the industry vs people doing it at their own house
I wish I would have used knee pads in 1991 when I started doing trim work. Fast forward to 2018 when I had knee replacement surgery. I am grateful to be able to stand on the shop floor and build some cabinets 3-4hrs on a good day. I'm 47yrs old and on disability and it's 100% caused by being the tough man who .... out of a combination of ignorance and ego didn't take care of the most important tool you have.
Great video.... I wish I'd have had TH-cam 30yrs ago!!
Dude congratulations you are doing a very good job, and for sure helping a lot of people, please make more videos like that
Good advice on the knees. I'm 51 and definitely feel it. Also running those same guns. Had good luck with both
Thanks for this video. I'm in the process of removing all the old baseboard in a 3 story home and replacing it. You've given me some great tips to do a better job. One of them is using a laser to measure I always measure corner cuts wrong. I going to buy a good tool for this.
Your vids sure have come a long way! Thank You.
you are one hell of a carpenter i know this because i am a carpenter as well
I am with you 100%. I install this type of trim the same way, no issues whatsoever. 🙏🏻👍🏻
Thank you so much for your help and insights to the carpentry trades. Extremely helpful and appreciated by myself as a young guy trying to start a business and I’m sure thousands of others. Thank you and big respect for your skills.
Thank you for the lesson.... valuable information you are passing on!
As a builder I try to mark all of my studs with paint for the trim crew. Great video
Thanks for this very informative video. Started a side job today doing some base and shoe and this made it so much more efficient then how I have done it in the past during my full time job.
I really like the minimalist nailing. Whoever did our baseboard trim hit it the way roofers nail shingles....bam bam bam bam bam bam bam. Move a few inches. Bam bam bam bam bam bam bam. And the little bullnose pieces at corners? The first one I pulled off looked like a little 5" porcupine.
You're right about the value of what we homeowners notice. The only place I'm really picky about the baseboard is the bathroom...because I have time to sit there and stare at it!!
Spencer!!! I own a cabinet installation business, I run lots of crown and lots base and lots of right rail trim. Your videos have helped me and my business grow substantially. Your tips and tricks have saved me lots of time and money, I appreciate you and your skill set.
Happy to help Edward! 👊
Any tips for running crown on top of full overlay cabinet's?? I've been building my "crown platform" on the ground then cutting all my crown to match my platform and assembling it and taking it up in one piece, just wondering if that's the best way to do it or if maybe you have anothe idea
You’re incredible! Thank you for sharing!
Job well done I'm also a carpenter and i like watching your videos because believe it or not i actually learned a few thing from you so NICE WORK AGAIN AND KEEP ON GOING!!!!
Thanks for the tips as im just staring off doing side work to pay the bills and the info on your videos have been awesome in being cost and time efficient.
That was very well explained, thanks!
I think I might rip my house to shreds just so I can take advantage of the skills you have taught on your videos. Amazing!
I would love to see a video of a stain grade flat profile trim like this used. As we all know when it's painted there's a lot of forgiveness.
Butt joining flat stock like this is the best way to keep the corners tight. I’ll never forget a customer I had years ago who was surprised I wasn’t mitering inside corners with this kind of material.
This video has added value to my perspective. Thanks.
Excellent video and great advice. Thanks for sharing your experience.
As a trim and handrail contractor myself I agree with you on how much fine detail is needed or not needed on some things. Trim now a days is for the most part, paint grade. So there’s a painter following behind you filling your small gaps. But I don’t install trim with the mentality of “try your best...caulk the rest”. Pride in work and efficiency is your only key to success.
Right. For the stuff like baseboard a good carpenter should be able to make it look perfect the first time every time at a production pace.
LOVE all of your videos bro!!
First off I think your videos are great. You are definitely a skilled and knowledgeable craftsman and I appreciate the time you take to share with us all. My comment is about the gap that almost always occurs in the lower portion of the baseboard at the inside corners. I work from left to right so before I install a room I go to every left inside corner and shoot a 15g -2.5" nail down low and at about a 45° angle into the bottom plate. It will stick out proud. If I am going from the corner to corner I will go slightly strong on my next measurement and when I install I fit the two corners and bow out the middle. When I push in the middle the nail will give a little but just enough that the fit is tight at both top and bottom at the inside corner. Throw some thorns in it and move on! Can't remember the last time I ever had to use a bar to pull the bottom of a baseboard out after I tried this. Works for square base and coped base. Just my 2 cents for what it's worth. Cheers!
Great tip. I'll definitely give that a try.
You made some good points at the end about value. I like that square baseboard too.
Great video and advice. Thx for sharing the tips.
As always, amazing video! I would still love to see why you switched from DiamondBack to Occidental's ! Thanks for taking the time to make these!
Stay tuned. That video is on the list to make for the near future.
Thanks for the great comments on job value.
Best trim video ever. Period.
Great video - nice insight into what constitutes value, and giving quality where it is not needed diminishes putting time where it is.
"always good to take your time and not do dumb stuff". Probably the best advice I've ever heard, lol!
I wish I had seen this two weeks ago. Great Video 👍
Clean work, Great advice as always.
When faced with that 1" ish piece behind the door, I nail it to the long trim from the rear corner & use chalking on wall. Never breaks and solid connection.
That's a great technique also. I've that done as well.
@@InsiderCarpentry pop I made this suggestion a year ago
Will delete one
Great job with your channel Spencer. I have done a lot of trim carpentry, but not nearly as much as you have. It is something I enjoy and strive to be the best I can be, but I no longer do it for a living full time. I did some remodeling and trimming for about 5 years and have gotten better, but I love your videos, and have learned a ton from you. Thank you. Keep up the good work. The one thing I have yet to get on board with is using a laser distance measure... I have a Milwaukee, but i'd love to see YOU do a video review of this distance measure. I'd love to own the Leica as I have used Leica optics and they are the finest in the world. Thank you for some awesome content. Ben Langton
Thanks for sharing great insights
So much great info!!!! Thanks for the knowledge!! Cheers!
Thanks for sharing your knowledge.
Nice! What I try to do..is do the external mitres first, that way, it gives you a bit of lee-way to to get the mitres fitting perfectly...then, your now shortened base board gaps at the internal corners can be filled with filler no problem. 👍
Thank you. Videos like yours are a godsend. 🙏🙏🙏
Nicely Done 📐🔨
Great Job
Thanks again Spencer - always a wealth of knowledge.
Great outlook on value and process!
Great tips and very well explained....thanks
I never thought of using a stud finder, so much faster, I would find a stud then mark the rest , takes a lot of time and unnecessary moving, I always lay all the flooring first then trim is the last...love all the tips
Thanks for some very good tips
Your very humble. You are very good also. I am also a trim carpenter . I really enjoy watching your videos.
Spencer, this may start sounding a bit strange coming from an 80 year old auto mechanic but ! I wish I had mechanics working for me that thought like you do carpentry. That being the away you approach your work . Seems to me you constantly are evaluating the job, “how can I improve, the ,quality, the speed , give my customer more value by selecting me , and make a good living at the same time”. Your common since approach and constant effort to refine your skills is a rare quality in the work force no matter what the industry. I doubt there are few nights your go to bed and not think about those things. You are a rare bird. , Mike
Rare bird indeed. LOL
Thanks for this video, very informative for me. I appreciate ya fella! Hope you have a blessed Holiday season.
Thanks! You too. 👍
God bless you. You are a good person for sharing your videos.
Great video, thank you!
When I learned framing layout, I was taught to lay everything out from left to right. This is helpful to know when nailing base. From left to right there is stud every 16”. That eliminates the need for stud finders.
Awesome work! Square butt insides always turn out the best with flat stock. As we know coped corners are the best corner. Another good tip to save a large amount of time is never numbering the walls or pieces. I always draw out the floor plan measure clockwise cut clockwise then distribute counter clockwise. I even save more time not crossing each number off my cut list. Only when I go to distribute the material or leave my cut bench for any reason I mark the next piece on my list so I know where I left off. Been doing it for 15 years lots.of time saved! Great videos keep up the good work. I love being able to pick up other peoples tricks of the trades.
I don’t like how the straight cut butts into the piece that’s been round over.
Coping corners was 2020 were not doing that in 2023