HVAC: Supco Super Boost Installation (Supco Super Boost Relay And Hard Start Capacitor) SUPCO SPP6
ฝัง
- เผยแพร่เมื่อ 17 มิ.ย. 2022
- HVACR (Heating, Ventilation, Air Conditioning/Refrigeration) Supco Super Boost Installation (Supco Super Boost Relay And Hard Start Capacitor) Supco SPP6 / How To Install Supco Super Boost SPP6 / How To Wire Supco Super Boost Relay And Hard Start Capacitor / Supco Hard Start Kit / How Do You Install A Super Boost Capacitor / How To Wire A Capacitor / How To Install a Capacitor / Capacitor Installation / Capacitor Wiring / HVAC Compressor Not Starting / AC Compressor Not Starting
How To Wire/Install A Hard Start Kit For AC/Refrigeration Systems (SUPCO 3 N 1 Installation)
• HVACR: How To Wire/Ins...
Applications:
Use on any single phase air-conditioner or refrigeration unit
Low voltage situations
Hard starting compressors
Specs:
Operating Voltage VAC: 90 to 277 VAC
Recommended Range (HP): 1/2 - 10 Horse Power
Capacitor size (µF): 130 to 156 MFD
Torque: 500%
Features/Benefits:
PTC Positive Temperature Coefficient Relay and Capacitor
Easy 2-wire installation
NATE® Recognized (Course #1867-0002)
Can be used on PSC type compressors
Most economic
UL® Recognized
Thanks for watching!
Email: JumperManTech@Gmail.com
Follow me on Instagram! @JumpRmantech - วิทยาศาสตร์และเทคโนโลยี
I bought one of these 15 years ago as an emergency backup and never needed it until now; thanksgiving week 2023. The refrigerator / freezer had already gone too warm before I noticed. I have the 5 wire version. It was quite simple to install.
At the compressor the factory starter and capacitor is attached to the side of the compressor. There is a small bent metal wire that wraps around both pieces; it just unhooks from the side you are on. It's meant to hold the capacitor and starter in place.
The two come off easily, you can probably pull it off by hand but I used a flat blade screwdriver to start prying it off.
Looking at the supco it has 3 blade female blade receivers on it. I was expecting the comproessor to have blades on it. The compressor actually has small round prongs. When I looked at the Supco terminals I realived they are shaped to accept either blade or the prongs. The directions for which wire goes to which prong are on the side of the supco, very easy to understand.
The other two wires did not have terminals on them and the instructions said to hook one to either supply line and the other one ges to the other supply line. What this means is the connector coming from the refrigerator plugs into the capacitor normally but in this case you have to cut the connector, strip the two wires (you can do it) and then twist one to each of the wires on the supco. You then need to put small wire nuts on each of the two wires but you could get by with electrical tape in pinch. The supco probably came with wire nuts originally but it was already out of the package and they were lost.
Tuck the supco in next to the compressor, plug in the refrigerator and it started right up.
My existing, original from 10 years ago starter was blackened and charred. A new set will not arrive for two days.
I then searched for supco start capacitor just because and saw this video and figured I would offer my tale of a quite easy repair.
Thank you so much for the best formal friendly use video
Bro I just used it super amazing thanks for the advice and tips. Keep up the great work!!!
Unfortunately, he didn’t show where should to connect compressor. Why I need to connect the Booster without compressor. Is it works without compressor? Where is compressor?
How to connect the compressor to the booster if it have the two wires only ?….
I wasted my time here ….
Great vid. Does the existing run capacitor need to be good in order to use this SPP6? Can I use this if there's no run cap in the system?
Thank you really helpful.
Can you install the boost capacitor if you only have a two terminal capacitor, like the one in the video, but the fan and the compressor are on the OEM capacitor?
Interesting and helpful video. Well presented and explained. Great job JMT
Unfortunately, he didn’t show where should to connect compressor. Why I need to connect the Booster without compressor. Is it works without compressor? Where is compressor?
How to connect the compressor to the booster if it have the two wires only ?….
I wasted my time here ..
@@yuriigorg721 The capacitor is connected to your compressor or motor. You connect this to the capacitor as shown. Thanks for watching 🔧⚡️
Thank you Izzy! Much appreciated 🙏🔧⚡️
@@yuriigorg721 You might be confusing this for the Supco 5-2-1 kit where there is a connection at the compressor itself and the 2 power wires feeding the compressor. I have a video on that too
Thank You
What the difference between spp6 and spp6E? And why some installers recommend 5-2-1 instead of this . Thank you
Interesting and helpful jmt well done
Unfortunately, he didn’t show where should to connect compressor. Why I need to connect the Booster without compressor. Is it works without compressor? Where is compressor?
How to connect the compressor to the booster if it have the two wires only ?….
Greetings JMT. A subscriber here. I have a True reach in freezer where the compressor is drawing high amps and so it won’t start. It’s a single phase 240volt. I have checked all the starting components; potential relay, run capacitor, and start capacitor and they all are good. I also have checked the compressor windings and they also checked out. And the compressor is definitely not shortened to ground. Do you think I should install this compressor booster in line with the run capacitor to see if it solves the issue before I go replacing the compressor which is over a thousand dollars? Thanks a lot in advance for your reply. And please keep posting more videos. I’m learning a lot watching them.
Thank you will be buying a super boost ,well explain "" B
Good vid and good explanation ... Thx ...
Unfortunately, he didn’t show where should to connect compressor. Why do I need to connect the Booster without compressor. Is it works without compressor? Where is compressor?
How to connect the compressor to the booster if it have the two wires only ?….
Can I use one of these to help start a window AC unit that I want to power with a 12v battery bank?
if the unit is 12V or you have an inverter
Does this reduce the lifespan of a compressor in your opinion? I mean if the compressor is “having a hard time starting” it’s probably on its last legs??
Unfortunately, he didn’t show where should to connect compressor. Why I need to connect the Booster without compressor. Is it works without compressor? Where is compressor?
How to connect the compressor to the booster if it have the two wires only ?….
I wasted my time here ..
i have a 5 ton AC system...what kind of Super Boost do i need?
Probably the SPP6
Very informative. Came here searching for information on this product because a tech installed it on our AC unit, then tried to upsell us on an EAC and APCO unit.
When we declined he charged us $500 for installation of the SPP6. Amazon shows it for pretty cheap too. Can the cost be attributed to service charge and/or labor?
Thanks for any input.
I ordered this, but it seems it’s the wrong item? This only has two wires. My capacitor has three prongs for the following wires: common, herm, and fan. Looks like I wasted my money, and I’m still roasting hot. 😢
the wire with the additional spade goes to common or "C" and the other goes to "HERM". Make sure discharge the dual run capacitor by using an insulated screwdriver and touch c to herm and c to fan making sure you hold onto insulated part of screwdriver.
Will Installing this reduced or cause any damage to the life of the compressor? My unit starts up every time although I do hear a loud noise when it kicks on. But after that it works great. We're in 2024 and the unit manufacturing date is 2006. Just want to make sure this product will not harm my unit as I love how it cools my home in Florida.
👍
I have a SPP5 can i replace it with a SPP6?
If they are both just 2 wires, you should be good. Just make sure it's rated for the same. Thanks for watching! Stay tuned for new videos every week🔧⚡️
Look into the HP rating and if they match 👍
I called the manufacturer and talked with a technician for the company of this product and they said it was fine to go up to 6 but do not go from 6 to 5. I'm just so grateful that we have this technology that we can discuss important issues like this thank you so much.
Pay a little more money for the 5-2-1 kit. 2 wire hard starts will usually fail within the warranty period and you will be going back to do a free service call. 5-2-1 kits are much better and have a lower fail rate.
😂😂😂 what if it has 3
Unfortunately, you didn’t show where should to connect compressor. Why I need to connect the Booster without compressor. Is it works without compressor? Where is compressor?
How to connect the compressor to the booster if it have the two wires only ?….
I wasted my time here ..
You are looking for instructions for a different product. I made a video on that too. I will leave a link to that video below.
3 N 1 Hard Start Kit
th-cam.com/video/sem9z0H1QmU/w-d-xo.html
We call these the "ole stick of dynamite " use the k2 potential relay way better
Not a relay
yes it does have one but 3 in 1 has potential relay which operates better by protecting the compressor better.