How to wire a Toyota Prado 150 Series Accessory Harness | Fridge Feed Installation
ฝัง
- เผยแพร่เมื่อ 5 ก.ย. 2024
- This video is an instructional video to show how to install an accessory harness into the 150 series Toyota Prado.
You can find dual battery kits to suit this vehicle on our website.
www.aussiedrif...
Awesome vids and products mate. I just purchased and installed the Prado150 kit you sell with accessory harness, battery tray and redarc charger. Saved heaps of time compared to previous installations I have done in other vehicles using only the redarc wiring kit. 😊
Nice vid mate thanks. Little tip when your using a spanner to tighten anything on a battery best to always start tightening after the second terminal so you don’t accidentally arc across the two posts with the spanner. Had a mate do it and blew his wedding ring to bits.
Great video mate, well explained and easy to understand. I have been looking for someone to do this to my new Prado, with your kit, I will just do it myself, it looks like you have a good buisness going and I hope you do well.
Thanks bill, glad the videos were helpful too mate
Thanks bill, glad the videos were helpful too mate
Best installation video I have ever seen. Nice
Glad it was helpful mate
Awesome descriptive video!
Where can I purchase the 3 way surface mount with the piggy back wiring? thanks
Hi Nathan, you can buy the whole harness with a triple socket housing option from this link www.aussiedriftertouring.com.au/shop/accessory-harness
Excellent Video !! Helped out Immensely :) !
Glad it was helpful mate
Great Vedio to watch and understad.
Glad it was helpful
Thanks for the video. I'm looking for wiring installation to roof of Prado 150. Appreciate if you can recommend any videos
Sorry we don’t have a video for that.
Awesome Vid thanks mate. This is exactly what I want to do with my Prado. Only difference is that I have a Redarc Isolator instead of the DC/DC Charger. 2014 model Prado. Can you plug a Solar Panel via a controller directly into one of the sockets and charge the Second Battery and run the harness directly to the Second Battery rather than to the Isolator terminals?
Hey mate. Yer so long as your solar panels have their own solar controller then you can connect them straight to the aux battery
How would you approach the grommet situation if you already have a cable running through with its own grommet?
Hi mate, in that case the original Toyota Gromit, the large one going through the firewall that contains the Toyota harness running into the vehicle has spare nipples that you can cut the end off and using a little bit of lubricant you can push the cable through those into the car. That designed for extra accessories to be installed. Hope that helps
A very informative video step by step
Thank you
Glad it was helpful
What size cable are you using to run to the back on the accessories harness? And would you be safely be able to run a fridge and other accessories off of it?
Hi Mate the cable size used depends on the type of harness and sockets selected. it is 6mm twin if using round sockets and 8 B&S bacle if selecting an anderson plug harness. They are all designed to run a fridge and other low current 12v circuits such as camp lights and charging usb gear.
@@AussieDrifterTouring thanks mate appreciate the quick reply
Great vid. What is the wire gauge or cross sectional area for the wires to the rear?
Hi Tim. The one in this video is 6mm twin. We do have one that has an anderson plug on it and it is 8 b&s cable.
Can you go through the Gromit on the right side of the bonnet through the firewall?
Hi Daniel, This harness is made to go through that specific grommet but the harness is 7m long and therefore long enough to reach anywhere in the rear. So if you looking to have your sockets on the passenger side then we recommend going through that grommet and then running behind the dash to the passenger side and then following the same procedure to run down the passenger side. Hope that helps, Cheers Kurt
@@AussieDrifterTouring Thanks Kurt! Much appreciated
@@AussieDrifterTouring Do you any videos or hints on how to get across behind the dash?
@@JeremyKozak-sl9cz Hey Jeremy, we don't have a video for that sorry mate but it's pretty easy. Once you drop the plastic covers down you can see the Toyota harness from left to right and you just cable tie to that. Hope that helps
@@AussieDrifterTouring getting the covers off is what I’m unsure of🤦
Does the new Prado 150 require the redarc to be connected/piggy back to an ignition wire source in the fuse box? Cheers.
Hi Stan, no mate it doesn't, they are still running a temperature compensating alternators so that is not required.
@@AussieDrifterTouring awesome thanks! Always confused smart alternator with temperature sensing one…
@@stansze8013 no worries mate, glad we could help 👍
Hi where buy wire
😅😅😅😅